AMPC-DE

BOHREN | T-A Pro® Bohrsystem mit austauschbaren Bohreinsätzen für hohe Vorschubgeschwindigkeiten

T-A Pro® Schnittwertempfehlungen | Zoll (inch)

Hartmetall

A

Feed Rate (IPR) by Diameter

Härte (HBW)

Bohr- einsatz

Speed (SFM)

3/8" - 33/64"

1/2" - 11/16"

45/64" - 15/16"

31/32" - 1-3/8"

1-13/32" - 1-7/8"

Material

Automatenstahl

100 - 150 150 - 200 200 - 250 85 - 125 125 - 175 175 - 225 225 - 275 125 - 175 175 - 225 225 - 275 275 - 325 125 - 175 175 - 225 225 - 275 275 - 325 325 - 375 225 - 300 300 - 350 350 - 400 100 - 150 150 - 250 250 - 350 150 - 200 200 - 250 140 - 220 220 - 310 140 - 220 220 - 310 185 - 275 275 - 350

P P P P P P P P P P P P P P P P P P P P P P P P

475 440 410 425 410 385 355 410 385 355 330 420 390 360 340 310 350 325 300 400 340 280 220 180

0.007 0.007 0.006 0.006 0.006 0.005 0.005 0.006 0.005 0.005 0.004 0.006 0.005 0.005 0.004 0.003 0.004 0.003 0.003 0.006 0.005 0.004 0.004 0.004 0.002 0.002 0.003 0.003 0.003 0.003

0.010 0.010 0.010 0.009 0.009 0.008 0.008 0.009 0.008 0.008 0.007 0.009 0.008 0.008 0.007 0.007 0.007 0.006 0.006 0.010 0.009 0.008 0.006 0.006 0.005 0.003 0.004 0.003 0.004 0.003

0.013 0.013 0.013 0.012 0.012 0.010 0.010 0.012 0.010 0.010 0.009 0.012 0.011 0.011 0.010 0.010 0.010 0.009 0.008 0.012 0.010 0.009 0.008 0.008 0.007 0.005 0.007 0.005 0.007 0.005

0.016 0.016 0.016 0.015 0.015 0.014 0.014 0.015 0.014 0.014 0.012 0.014 0.014 0.014 0.012 0.012 0.013 0.012 0.011 0.014 0.012 0.010 0.010 0.010 0.008 0.006 0.008 0.006 0.008 0.006

0.020 0.020 0.020 0.019 0.019 0.018 0.018 0.019 0.018 0.018 0.016 0.017 0.017 0.017 0.015 0.015 0.015 0.014 0.013 0.018 0.016 0.014 0.012 0.012 0.009 0.007 0.009 0.007 0.009 0.007

1111Mn30, 10S20, 11SMn36, etc.

BOHREN

Weiche Stähle mit

niedrigem Kohlenstoffgehalt C22, C10, CK22, 15Cr3, etc

B

Stähle mit mittlerem Kohlenstoffgehalt C45, C60, 30Mn5, etc.

Legierte Stähle

P

42CrM04, 36NiCr10, 10NiCrMo13 4, etc.

AUSDREHEN

Hochlegierte Stähle

34NiCrMo8, etc.

C

Baustahl

1St37, St52, S355, etc.

Werkzeugstähle

1.2714, 1.2312, 1.2379, 1.2344 etc.

Hochtemperaturlegierung Hastelloy B, Inconel 600, etc.

M 110 M 85 M 150 M 120 M 150 M 120

REIBEN

Titanlegierung

S

1.4571 etc.

Legierung Aerospace

S82

D

7xD und 10xD Einstellbeispiel (Faktor 0.80) Datenwert • Korrekturwert

12xD und 15xD Einstellbeispiel (Faktor 0.80) Datenwert • Korrekturwert

ROLLIEREN

Schnittwerte (7xD)

Schnittwerte (12xD)

200 SFM • 0.80 0.008 IPR • 0.80

= 160 SFM = 0.0064 IPR

200 SFM • 0.70 0.008 IPR • 0.70

= 140 SFM = 0.0056 IPR

Empfehlungen Kühlschmierstoff

E

Extra Kurz, 3xD, 5xD

7xD, 10xD

12xD, 15xD

Druck PSI

Durchfluss GPM

Druck PSI

Durchfluss GPM

Druck PSI

Durchfluss GPM

Serie

Z 0 1 2 3

450 350 300 250 200

4 6 8

550 450 400 350 300

6 9

650 550 500 450 400

8

12 12 16 18

10 13 14

10 12

GEWINDEFRÄSEN

WARNING

Tool failure can cause serious injury. To prevent: - When using holders without support bushing, use a short T-A Pro holder to establish an initial hole that is a minimum of 2 diameters deep. - Do not rotate tool holders more than 50 RPM unless it is engaged with the workpiece or fixture. Visit www.alliedmachine.com/DeepHoleGuidelines for the most up-to-date information and procedures. Factory technical assistance is available for your specific applications through our Application Engineering department. emai l : en gineeri ng.eu@ a lliedmachine.com IMPORTANT: The speeds and feeds listed above are a general starting point for all applications. Refer to the coolant recommendation chart for coolant requirements to run at the recommended speeds and feeds. Factory technical assistance is available through our Application Engineering department. For 7xD, 10xD, 12xD, and 15xD holder lengths, see adjustment example above.

X

A25: 62

www.alliedmachine.com | +49 (0) 7022 408-0 | info@wohlhaupter.com

SONDERWERKZEUGE