Drilling Product Catalog

DRILLING | T-A Pro® High Penetration Replaceable Insert Drilling System

3 Series: 35.05 mm - 47.80 mm (1.3798" - 1.8820")

Holders

A25

Imperial Holders

Body

Shank

Part No.

L 2

L 4

L 3

L 1

L 5

D 2

Length Sub Series

With Flat

Cylindrical

HTA3A01-150F HTA3B01-150F HTA3C01-150F HTA3D01-150F HTA3A03-150F HTA3B03-150F HTA3C03-150F HTA3D03-150F HTA3A05-150F HTA3B05-150F HTA3C05-150F HTA3D05-150F HTA3A07-150F HTA3B07-150F HTA3C07-150F HTA3D07-150F HTA3A10-150F HTA3B10-150F HTA3C10-150F HTA3D10-150F HTA3A12-150F HTA3B12-150F HTA3C12-150F HTA3D12-150F HTA3A15-150F HTA3B15-150F HTA3C15-150F HTA3D15-150F

HTA3A01-150C HTA3B01-150C HTA3C01-150C HTA3D01-150C HTA3A03-150C HTA3B03-150C HTA3C03-150C HTA3D03-150C HTA3A05-150C HTA3B05-150C HTA3C05-150C HTA3D05-150C HTA3A07-150C HTA3B07-150C HTA3C07-150C HTA3D07-150C HTA3A10-150C HTA3B10-150C HTA3C10-150C HTA3D10-150C HTA3A12-150C HTA3B12-150C HTA3C12-150C HTA3D12-150C HTA3A15-150C HTA3B15-150C HTA3C15-150C HTA3D15-150C

Stub Stub Stub Stub 3xD 3xD 3xD 3xD 5xD 5xD 5xD 5xD 7xD 7xD 7xD 7xD 10xD 10xD 10xD 10xD 12xD 12xD 12xD 12xD 15xD 15xD 15xD 15xD

A B C 1.618 3.634 3.821 6.322 2.688 1-1/2 1.618 3.634 3.821 6.322 2.688 1-1/2 1.618 3.634 3.821 6.322 2.688 1-1/2 D 1.618 3.634 3.821 6.322 2.688 1-1/2 4.854 7.089 7.276 9.777 2.688 1-1/2 4.854 7.089 7.276 9.777 2.688 1-1/2 4.854 7.089 7.276 9.777 2.688 1-1/2 D 4.854 7.089 7.276 9.777 2.688 1-1/2 8.090 10.325 10.512 13.013 2.688 1-1/2 8.090 10.325 10.512 13.013 2.688 1-1/2 8.090 10.325 10.512 13.013 2.688 1-1/2 D 8.090 10.325 10.512 13.013 2.688 1-1/2 A 11.326 13.561 13.748 16.249 2.688 1-1/2 11.326 13.561 13.748 16.249 2.688 1-1/2 11.326 13.561 13.748 16.249 2.688 1-1/2 D 11.326 13.561 13.748 16.249 2.688 1-1/2 A 16.180 18.415 18.602 21.103 2.688 1-1/2 16.180 18.415 18.602 21.103 2.688 1-1/2 16.180 18.415 18.602 21.103 2.688 1-1/2 D 16.180 18.415 18.602 21.103 2.688 1-1/2 A 19.416 21.651 21.838 24.339 2.688 1-1/2 19.416 21.651 21.838 24.339 2.688 1-1/2 19.416 21.651 21.838 24.339 2.688 1-1/2 D 19.416 21.651 21.838 24.339 2.688 1-1/2 A 24.270 26.505 26.692 29.193 2.688 1-1/2 24.270 26.505 26.692 29.193 2.688 1-1/2 24.270 26.505 26.692 29.193 2.688 1-1/2 D 24.270 26.505 26.692 29.193 2.688 1-1/2 A B C A B C B C B C B C B C

Connection Accessories

Nylon Locking Screws 7514N-IP20-1

Admissible Tightening Torque*

Insert Screws 7514-IP20-1

Insert Driver

8IP-20 1370 N-cm (121.3 in-lbs) *Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength. 3 Series Holder Diameter Range Sub Series 3A 3B 3C 3D Metric (mm) 35.05 mm - 47.80 mm 37.80 mm - 47.80 mm 41.00 mm - 47.80 mm 44.40 mm - 47.80 mm Imperial (inch) 1.3798" - 1.8820" 1.4880" - 1.8820" 1.6140" - 1.8820" 1.7479" - 1.8820" Refer to Speed and Feed charts for recommended adjustments to speeds and feeds. Refer to page A25: 64 for deep hole drilling guidelines in this section of the catalog. Visit www.alliedmachine.com/DeepHoleGuidelines for the most up-to-date information and procedures. Factory technical assistance is available for your specific applications through our Application Engineering department : appeng@alliedmachine.com. WARNING

A25: 33 - 38

A25: 51 - 61

Key on A25: 2

Screws sold in multiples of 10. = Metric (mm) = Imperial (in)

www.alliedmachine.com | 1.330.343.4283

A25: 40