Drilling Product Catalog

DRILLING | APX™ Drill: Deep Hole / Large Diameter Replaceable Insert Drilling System

95 Series: 95.00 mm - 101.60 mm (3.7400" - 4.0001")

Heads

T-A® Style Head

GEN3SYS® Style Head

APX Heads

T-A Style Head

GEN3SYS Style Head

D 1

D 3

L 9

L 9

IC Insert Size mm inch 14.29 9/16 14.29 9/16 14.29 9/16 14.29 9/16 14.29 9/16 14.29 9/16 14.29 9/16 14.29 9/16

mm inch

Fractional

mm inch mm inch

Part No.

mm inch 8.7 0.344 8.7 0.344 8.7 0.344 8.7 0.344 8.7 0.344 8.7 0.344 8.7 0.344 8.7 0.344

Part No.

V9502S-0324 V9502S-96 V9502S-0326 V9502S-98 V9502S-0328 V9502S-100 V9502S-0330 V9502S-0400

V9532S-0324 V9532S-96 V9532S-0326 V9532S-98 V9532S-0328 V9532S-100 V9532S-0330 V9532S-0400

95.25 3.7500 3-3/4 34.93 1-3/8 10.5 0.414 96.00 3.7795 — 34.93 1-3/8 10.5 0.414 96.84 3.8125 3-13/16 34.93 1-3/8 10.5 0.414 98.00 3.8583 — 34.93 1-3/8 10.5 0.414 98.43 3.8750 3-7/8 34.93 1-3/8 10.5 0.414 100.00 3.9370 — 34.93 1-3/8 10.5 0.414 100.01 3.9375 3-15/16 34.93 1-3/8 10.5 0.414

101.60 4.0000

4

34.93 1-3/8 10.5 0.414

A50

Pilot Inserts

D 1 Range

D 3

T-A Style Head

GEN3SYS Style Head

mm

inch

mm inch Pilot Series

T-A Pro®

T-A (-TC)

Pilot Series

XT Pro

95.00 - 101.60 3.7400 - 4.0001 34.93 XT#32-34.93 #: Denotes ISO material/geometry (P= steel, M= stainless steel, K= cast iron, N= nonferrous, and X= high-speed steel substrate). X is only available in T-A Pro inserts. 1-3/8 2 TA#2-34.93 1C12H-0112-TC 29

IC Inserts - AM300® Coated Size Geometry mm inch

Part No. P35 (C5)

Insert Driver

Admissible Tightening Torque*

Insert Screw

K35 (C1)

K25 (C2)

OP-090608-1PW OP-090608-PW OP-090608-2PW

Standard High Rake

1370 N-cm (121.0 in-lbs)

14.29 9/16

75014-IP20-1 8IP-20

— OP-090608-PWHR — *Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength.

Pilot Accessories T-A Series

GEN3SYS Series

Insert Screws 7495-IP15-1

Insert Driver

Admissible Tightening Torque*

2

32

8IP-15

690 N-cm (61.0 in-lbs)

*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength.

Wear pads sold in multiples of 2. Wear pad screws sold in multiples of 4. IC inserts sold in multiples of 2. Insert screws sold in multiples of 10.

NOTE: For standard metric sized pilot inserts, please see the cross reference on pg. A50: 33 .

A50: 29 - 32

A25 & A30

A20

Key on A50: 2

For nonstocked diameters, follow the below examples: Metric 95 series, T-A (2 series), 100.25 mm

= V9502S-100.25 = V9532S-3.9450

Inch

95 series, GEN3 (32 series), 3.9450"

A50: 27

www.alliedmachine.com | 1.330.343.4283