A25-TAP_US-EN
2
DRILLING | T-A Pro® High Penetration Replaceable Insert Drilling System
T-A Pro Drill Holders
A
2 Series Metric | Diameter Range: 24.38 mm - 35.04 mm
L 1
DRILLING
L 7
L 4
D 2
L 2
L 3
B
Body
Shank
Length Sub Series
Flat Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No
Part No
L 2
L 4
L 3
L 1
L 7
D 2 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32
BORING
HTA2A01-32FM HTA2A01-32CM HTA2B01-32FM HTA2B01-32CM HTA2C01-32FM HTA2C01-32CM HTA2D01-32FM HTA2D01-32CM HTA2A03-32FM HTA2A03-32CM HTA2B03-32FM HTA2B03-32CM HTA2C03-32FM HTA2C03-32CM HTA2D03-32FM HTA2D03-32CM HTA2A05-32FM HTA2A05-32CM HTA2B05-32FM HTA2B05-32CM HTA2C05-32FM HTA2C05-32CM HTA2D05-32FM HTA2D05-32CM HTA2A07-32FM HTA2A07-32CM HTA2B07-32FM HTA2B07-32CM HTA2C07-32FM HTA2C07-32CM HTA2D07-32FM HTA2D07-32CM
STUB STUB STUB STUB STUB STUB STUB STUB
A A B B C C D D A A B B C C D D A A B B C C D D A A B B C C D D
29.7 29.7 29.7 29.7 29.7 29.7 29.7 29.7 89.2 89.2 89.2 89.2 89.2 89.2 89.2 89.2
75.0 75.0 75.0 75.0 75.0 75.0 75.0 75.0
78.6 78.6 78.6 78.6 78.6 78.6 78.6 78.6
132.9 132.9 132.9 132.9 132.9 132.9 132.9 132.9 195.4 195.4 195.4 195.4 195.4 195.4 195.4 195.4 254.8 254.8 254.8 254.8 254.8 254.8 254.8 254.8 314.3 314.3 314.3 314.3 314.3 314.3 314.3 314.3
60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0
C
3xD 3xD 3xD 3xD 3xD 3xD 3xD 3xD 5xD 5xD 5xD 5xD 5xD 5xD 5xD 5xD 7xD 7xD 7xD 7xD 7xD 7xD 7xD 7xD
137.4 137.4 137.4 137.4 137.4 137.4 137.4 137.4 196.9 196.9 196.9 196.9 196.9 196.9 196.9 196.9 256.4 256.4 256.4 256.4 256.4 256.4 256.4 256.4
141.0 141.0 141.0 141.0 141.0 141.0 141.0 141.0 200.5 200.5 200.5 200.5 200.5 200.5 200.5 200.5 260.0 260.0 260.0 260.0 260.0 260.0 260.0 260.0
REAMING
148.7 148.7 148.7 148.7 148.7 148.7 148.7 148.7 208.2 208.2 208.2 208.2 208.2 208.2 208.2 208.2
D
BURNISHING
E
Connection Accessories
THREADING
Admissible Tightening Torque* 61.0 in-lbs (690 N-cm)
Insert Screws 7495-IP15-1
Nylon Locking Screws
Insert Driver
Replacement Tips
Preset Torque Hand Driver
7495N-IP15-1
8IP-15
8IP-15TL
8IP-15B
*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength
Refer to Speed and Feed charts for recommended adjustments to speeds and feeds. Refer to page A25: 6 8 for deep hole drilling guidelines in this section of the catalog. Visit www.alliedmachine.com/DeepHoleGuidelines for the most up-to-date information and procedures. Factory technical assistance is available for your specific applications through our Application Engineering department. ext: 7611 | email: appeng@alliedmachine.com WARNING
X
A25: 58 - 65
A25: 34 - 37
A25: 38 - 41
SPECIALS
Key on A25: 1
Screws sold in multiples of 10 = Imperial (in) = Metric (mm)
A25: 44
www.alliedmachine.com | 1.330.343.4283
Made with FlippingBook - Online catalogs