A91-SSD_EU-EN

22

DRILLING | Structural Steel SoluƟons | GEN3SYS® XT Pro and GEN3SYS® XT Replaceable Insert Drills

22 Series | Diameter Range: 22.00 mm - 23.99 mm (0.8661" - 0.9448") GEN3SYS® XT Pro / GEN3SYS® XT Structural Steel Drilling System

A

D 1

DRILLING

140°

GEN3SYS® XT Pro

GEN3SYS® XT

Inserts

Insert

B

D 1 mm

D 1 inch 0.8661 0.8752 0.9055 0.9374

FracƟonal Equivalent

GEN3SYS® XT Pro Part No.

GEN3SYS® XT Part No.

XTST22-22.00 XTST22-22.23 XTST22-23.00 XTST22-23.81

7C222P-22ST 7C222P-0028ST

22.00 22.23 23.00 23.81

-

7/8

BORING

-

-

7C222P-0030ST

15/16

L 1

L 7

L 4

D 2

C

L 2

P 1

L 3

Holders REAMING

Body

Shank

L 2

L 4

L 3

L 1

L 7

D 2 25 25 25 25 25 25 25 25

P 1

Length

Flat YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES

Part No.

ST01220-25FM ST01225-25FM ST03220-25FM ST03225-25FM* ST05220-25FM ST05225-25FM* ST07220-25FM ST07225-25FM* ST01220-100F ST01225-100F ST03220-100F ST03225-100F* ST05220-100F ST05225-100F* ST07220-100F ST07225-100F*

1.5xD 1.5xD

36.0 36.0 72.0 72.0

69.3 69.3

72.7 72.7

125.3 125.3 161.3 161.3 209.3 209.3 257.3 257.3 5.000 5.000 6.422 6.422 8.313 8.313

56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0

1/8 BSPT 1/8 BSPT 1/8 BSPT 1/8 BSPT 1/8 BSPT 1/8 BSPT 1/8 BSPT 1/8 BSPT 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT

3xD 3xD 5xD 5xD 7xD 7xD 3xD 3xD 5xD 5xD 7xD 7xD

105.3 105.3 153.3 153.3 201.3 201.3 2.719 2.719 4.141 4.141 6.031 6.031 7.922 7.922

108.7 108.7 156.7 156.7 204.7 204.7 2.859 2.859 4.281 4.281 6.172 6.172 8.063 8.063

119.9 119.9 167.9 167.9 1.406 1.406 2.828 2.828 4.719 4.719 6.609 6.609

D

BURNISHING

1.5xD 1.5xD

2.281 2.281 2.281 2.281 2.281 2.281 2.281 2.281

1 1 1 1 1 1 1 1

10.203 10.203

*Oversized body holder (minimum drill diameter = 23 mm) ConnecƟon Accessories

E

THREADING

Admissible Tightening Torque* 305 N-cm (27.0 in-lbs)

Insert Screws

Nylon Locking Screws

Insert Driver

Replacement Tips

Preset Torque Hand Driver

739-IP9-1

739N-IP9-1

8IP-9

8IP-9TL

8IP-9B

*Tightening torques are calculated with a fricƟon coefficient of µ = 0.14 and develop 90% of ulƟmate yield strength.

X

Inserts sold in mulƟples of 1. | Screws sold in mulƟples of 10. = Metric (mm) = Imperial (in) NOTICE: Structural steel GEN3SYS holders are specifically designed to be used only with GEN3SYS XT Pro and GEN3SYS XT structural steel geometry inserts. Using other GEN3SYS XT or XT Pro insert geometries in these holders could lead to chip packing and tool failure. Contact ApplicaƟon Engineering for quesƟons regarding proper use of tools. email: engineering.eu@alliedmachine.com A91: 66 - 67 A91: 24 - 25 Key on A91: 1

SPECIALS

A91: 34

www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com