A91-SSD_EU-EN

DRILLING | Structural Steel SoluƟons | GEN3SYS® XT Pro and GEN3SYS® XT Replaceable Insert Drills

A

DRILLING

Feed Rate (mm/rev) by Diameter

17 series 32 series (17.00 mm - 17.99 mm) (18.00 mm - 19.99 mm) (20.00 mm - 21.99 mm) (22.00 mm - 23.99 mm) (24.00 mm - 25.99 mm) (26.00 mm - 28.99 mm) (29.00 mm - 31.99 mm) (32.00 mm - 35.00 mm) 0.30 0.36 0.38 0.41 0.43 0.46 0.48 0.48 0.25 0.30 0.36 0.38 0.41 0.43 0.46 0.46 0.23 0.28 0.30 0.33 0.36 0.38 0.41 0.41 18 series 20 series 22 series 24 series 26 series 29 series

B

BORING

Feed Rate (IPR) by Diameter

17 series

18 series

20 series

22 series

24 series

26 series

29 series

32 series

(0.6693" - 0.7086")

(0.7087" - 0.7873")

(0.7874" - 0.8660")

(0.8661" - 0.9448")

(0.9449" - 1.0235")

(1.0236" - 1.1416")

(1.1417" - 1.2597")

(1.2598" - 1.3780")

0.012 0.010 0.009

0.014 0.012 0.011

0.015 0.014 0.012

0.016 0.015 0.013

0.017 0.016 0.014

0.018 0.017 0.015

0.019 0.018 0.016

0.019 0.018 0.016

C

REAMING

D

Feed Rate (mm/rev) by Diameter

BURNISHING

18 series

20 series

22 series

24 series

26 series

29 series

32 series

(18.00 mm - 19.99 mm)

(20.00 mm - 21.99 mm)

(22.00 mm - 23.99 mm)

(24.00 mm - 25.99 mm)

(26.00 mm - 28.99 mm)

(29.00 mm - 31.99 mm)

(32.00 mm - 35.00 mm)

0.36 0.30 0.28

0.38 0.36 0.30

0.41 0.38 0.33

0.43 0.41 0.36

0.46 0.43 0.38

0.48 0.46 0.41

0.48 0.46 0.41

Feed Rate (IPR) by Diameter

E

18 series

20 series

22 series

24 series

26 series

29 series

32 series

THREADING

(0.7087" - 0.7873")

(0.7874" - 0.8660")

(0.8661" - 0.9448")

(0.9449" - 1.0235")

(1.0236" - 1.1416")

(1.1417" - 1.2597")

(1.2598" - 1.3780")

0.014 0.012 0.011

0.015 0.014 0.012

0.016 0.015 0.013

0.017 0.016 0.014

0.018 0.017 0.015

0.019 0.018 0.016

0.019 0.018 0.016

X

NOTE: The speeds and feeds listed above are based on a rigid setup using air mist through tool coolant. Speed may be increased up to 50% if using high pressure flood or through coolant. NOTE: If drilling dry without coolant, speed must be reduced significantly based on setup, drill depth, and material hardness. Up to 50% speed and feed reducƟon may be necessary in these types of applicaƟons. Contact the ApplicaƟon Engineering department for assistance. email: engineering.eu@alliedmachine.com NOTE: If drilling material thickness of 12.7 mm (0.500") or less, a minimum of 10% reducƟon in feed is required to minimise material deflecƟon.

SPECIALS

www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com

A91: 67

Made with FlippingBook - professional solution for displaying marketing and sales documents online