AMPC_EU-EN

Y

DRILLING | T-A Pro® High PenetraƟon Replaceable Insert Drilling System T-A Pro Drill Holders Y Series Metric | Diameter Range: 9.50 mm - 11.09 mm

A

L 1

L 5

L 4

DRILLING

D 2

L 2

L 3

B

Body

Shank

L 2

L 4

L 3

L 1

L 5

D 2 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20

Length Sub Series

Flat Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No

Part No

BORING

HTAYA01-20FM HTAYA01-20CM HTAYB01-20FM HTAYB01-20CM HTAYA03-20FM HTAYA03-20CM HTAYB03-20FM HTAYB03-20CM HTAYA05-20FM HTAYA05-20CM HTAYB05-20FM HTAYB05-20CM HTAYA07-20FM HTAYA07-20CM HTAYB07-20FM HTAYB07-20CM HTAYA10-20FM HTAYA10-20CM HTAYB10-20FM HTAYB10-20CM HTAYA12-20FM HTAYA12-20CM HTAYB12-20FM HTAYB12-20CM HTAYA15-20FM HTAYA15-20CM HTAYB15-20FM HTAYB15-20CM

Stub Stub Stub Stub 3xD 3xD 3xD 3xD 5xD 5xD 5xD 5xD 7xD 7xD 7xD 7xD 10xD 10xD 10xD 10xD 12xD 12xD 12xD 12xD 15xD 15xD 15xD 15xD

A A B B A A B B A A B B A A B B A A B B A A B B A A B B

11.1 11.1 11.1 11.1 33.2 33.2 33.2 33.2 55.4 55.4 55.4 55.4 77.5 77.5 77.5 77.5

39.5 39.5 39.5 39.5 64.9 64.9 64.9 64.9 87.0 87.0 87.0 87.0

41.5 41.5 41.5 41.5 66.9 66.9 66.9 66.9 89.1 89.1 89.1 89.1

89.5 89.5 89.5 89.5

50.0 50.0 50.0 50.0 50.0 50.0 50.0 50.0 50.0 50.0 50.0 50.0 50.0 50.0 50.0 50.0 50.0 50.0 50.0 50.0 50.0 50.0 50.0 50.0 50.0 50.0 50.0 50.0

114.9 114.9 114.9 114.9 137.1 137.1 137.1 137.1 159.2 159.2 159.2 159.2 192.4 192.4 192.4 192.4 214.6 214.6 214.6 214.6 247.8 247.8 247.8 247.8

C

REAMING

109.2 109.2 109.2 109.2 142.4 142.4 142.4 142.4 164.6 164.6 164.6 164.6 197.8 197.8 197.8 197.8

111.2 111.2 111.2 111.2 144.4 144.4 144.4 144.4 166.6 166.6 166.6 166.6 199.8 199.8 199.8 199.8

110.7 110.7 110.7 110.7 132.9 132.9 132.9 132.9 166.1 166.1 166.1 166.1

D

BURNISHING

ConnecƟon Accessories

Y Series Holder Diameter Range Metric (mm)

Admissible Tightening Torque*

Sub Series

Imperial (inch)

Replacement Tips

Preset Torque Hand Driver

Insert Screws Nylon Locking Screws

Insert Driver

E

YA YB

9.50 mm - 11.09 mm 0.3739" - 0.4368" 10.32 mm - 11.09 mm 0.4062" - 0.4368"

724-IP7-1

724N-IP7-1

8IP-7

8IP-7TL

8IP-7B 84 N-cm (7.4 in-lbs)

THREADING

*Tightening torques are calculated with a fricƟon coefficient of µ = 0.14 and develop 90% of ulƟmate yield strength.

Refer to Speed and Feed charts for recommended adjustments to speeds and feeds. Refer to page A25: 58 for deep hole drilling guidelines in this secƟon of the catalogue. Visit www.alliedmachine.com/DeepHoleGuidelines for the most up-to-date informaƟon and procedures. Factory technical assistance is available for your specific applicaƟons through our ApplicaƟon Engineering department. emai l : engineering.eu@alliedmachine.com WARNING

X

A25: 10 - 11

A25: 48 - 55

SPECIALS

Key on A25: 1

Screws sold in mulƟples of 10. = Metric (mm) = Imperial (in)

A25: 12

www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com