AMPC_EU-EN

0

DRILLING | T-A Pro® High PenetraƟon Replaceable Insert Drilling System

T-A Pro Drill Holders

0 Series Imperial | Diameter Range: 0.4999" - 0.6946"

A

L 1

L 5

L 4

DRILLING

D 2

L 2

L 3

Body

Shank

B

L 2

L 4

L 3

L 1

L 5

D 2

Length Sub Series

Flat Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No

Part No

HTA0A01-075F HTA0A01-075C HTA0B01-075F HTA0B01-075C HTA0C01-075F HTA0C01-075C HTA0D01-075F HTA0D01-075C HTA0A03-075F HTA0A03-075C HTA0B03-075F HTA0B03-075C HTA0C03-075F HTA0C03-075C HTA0D03-075F HTA0D03-075C HTA0A05-075F HTA0A05-075C HTA0B05-075F HTA0B05-075C HTA0C05-075F HTA0C05-075C HTA0D05-075F HTA0D05-075C HTA0A07-075F HTA0A07-075C HTA0B07-075F HTA0B07-075C HTA0C07-075F HTA0C07-075C HTA0D07-075F HTA0D07-075C

Stub Stub Stub Stub Stub Stub Stub Stub 3xD 3xD 3xD 3xD 3xD 3xD 3xD 3xD 5xD 5xD 5xD 5xD 5xD 5xD 5xD 5xD 7xD 7xD 7xD 7xD 7xD 7xD 7xD 7xD

A A B B C C D D A A B B C C D D A A B B C C D D A A B B C C D D

0.603 0.603 0.603 0.603 0.603 0.603 0.603 0.603 1.809 1.809 1.809 1.809 1.809 1.809 1.809 1.809 3.015 3.015 3.015 3.015 3.015 3.015 3.015 3.015 4.221 4.221 4.221 4.221 4.221 4.221 4.221 4.221

1.731 1.731 1.731 1.731 1.731 1.731 1.731 1.731 3.064 3.064 3.064 3.064 3.064 3.064 3.064 3.064 4.270 4.270 4.270 4.270 4.270 4.270 4.270 4.270 5.476 5.476 5.476 5.476 5.476 5.476 5.476 5.476

1.838 1.838 1.838 1.838 1.838 1.838 1.838 1.838 3.171 3.171 3.171 3.171 3.171 3.171 3.171 3.171 4.377 4.377 4.377 4.377 4.377 4.377 4.377 4.377 5.583 5.583 5.583 5.583 5.583 5.583 5.583 5.583

3.761 3.761 3.761 3.761 3.761 3.761 3.761 3.761 5.094 5.094 5.094 5.094 5.094 5.094 5.094 5.094 6.300 6.300 6.300 6.300 6.300 6.300 6.300 6.300 7.506 7.506 7.506 7.506 7.506 7.506 7.506 7.506

2.030 2.030 2.030 2.030 2.030 2.030 2.030 2.030 2.030 2.030 2.030 2.030 2.030 2.030 2.030 2.030 2.030 2.030 2.030 2.030 2.030 2.030 2.030 2.030 2.030 2.030 2.030 2.030 2.030 2.030 2.030 2.030

3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4

BORING

C

REAMING

D

BURNISHING

E

ConnecƟon Accessories

0 Series Holder Diameter Range Metric (mm)

Admissible Tightening Torque*

THREADING Sub Series

Imperial (inch)

Replacement Tips

Preset Torque Hand Driver

Insert Screws

Nylon Locking Screws

Insert Driver

0A 0B 0C 0D

12.70 mm - 17.64 mm 0.4999" - 0.6946" 14.00 mm - 17.64 mm 0.5510" - 0.6946" 15.08 mm - 17.64 mm 0.5936" - 0.6946" 16.50 mm - 17.64 mm 0.6495" - 0.6946"

A/B 72556-IP8-1 72556N-IP8-1 C/D 72567-IP8-1 72567N-IP8-1

8IP-8 8IP-8

8IP-8TL 8IP-8TL

8IP-8B 175 N-cm (15.5 in-lbs)

8IP-8B 175 N-cm (15.5 in-lbs) *Tightening torques are calculated with a fricƟon coefficient of µ = 0.14 and develop 90% of ulƟmate yield strength.

Refer to Speed and Feed charts for recommended adjustments to speeds and feeds. Refer to page A25: 58 for deep hole drilling guidelines in this secƟon of the catalogue. Visit www.alliedmachine.com/DeepHoleGuidelines for the most up-to-date informaƟon and procedures. Factory technical assistance is available for your specific applicaƟons through our ApplicaƟon Engineering department. emai l : engineering.eu@alliedmachine.com WARNING

X

A25: 18 - 19

A25: 48 - 55

SPECIALS

Key on A25: 1

Screws sold in mulƟples of 10. = Metric (mm) = Imperial (in)

A25: 22

www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com