AMPC_EU-FR
REAMING | ALVAN® Reaming Systems by S.C.A.M.I. Recommended Cutting Data | Metric (mm) Monobloc Style
A
Speed (m/min)
Recommended Feed (mm/rev) by Reamer Diameter
DRILLING
5.80 mm - 10.00 mm 10.01 mm - 22.00 mm 22.01 mm - 32.10 mm Lead A, G Lead E, N, M Lead A, G Lead E, N, M Lead A, G Lead E, N, M 0.20 - 0.40 0.30 - 0.60 0.40 - 0.60 0.40 - 1.00 0.50 - 0.80 0.60 - 1.20 0.20 - 0.40 0.30 - 0.50 0.30 - 0.60 0.30 - 0.80 0.40 - 0.70 0.40 - 1.00 0.20 - 0.40 0.30 - 0.60 0.40 - 0.60 0.40 - 1.00 0.50 - 0.80 0.60 - 1.20 0.20 - 0.40 0.30 - 0.50 0.30 - 0.60 0.30 - 0.80 0.40 - 0.70 0.40 - 1.00 0.20 - 0.40 0.30 - 0.60 0.40 - 0.60 0.40 - 1.00 0.50 - 0.80 0.60 - 1.20 0.20 - 0.40 0.30 - 0.50 0.30 - 0.60 0.30 - 0.80 0.40 - 0.70 0.40 - 1.00 0.20 - 0.40 0.30 - 0.60 0.40 - 0.60 0.40 - 1.00 0.50 - 0.80 0.60 - 1.20 0.20 - 0.40 0.30 - 0.50 0.30 - 0.60 0.30 - 0.80 0.40 - 0.70 0.40 - 1.00 0.15 - 0.30 0.20 - 0.40 0.20 - 0.50 0.30 - 0.60 0.30 - 0.60 0.40 - 0.80 0.20 - 0.40 0.30 - 0.60 0.40 - 0.60 0.40 - 1.00 0.50 - 0.80 0.60 - 1.20 0.20 - 0.40 0.30 - 0.50 0.30 - 0.60 0.30 - 0.80 0.40 - 0.70 0.40 - 1.00 0.20 - 0.40 0.30 - 0.60 0.40 - 0.60 0.40 - 1.00 0.50 - 0.80 0.60 - 1.20 0.20 - 0.40 0.30 - 0.50 0.30 - 0.60 0.30 - 0.80 0.40 - 0.70 0.40 - 1.00
Hard ness (BHN)
Uncoated Carbide
Coated Carbide Cermet 60 - 80 90 - 300
ISO Material
Free-Machining Steel 1118, 1215, 12L14, etc.
100 - 180
7 - 15
180 - 250 6 - 10
40 - 70
80 - 200
Low-Carbon Steel
85 - 180 180 - 275 125 - 180
7 - 15 6 - 10 7 - 15
60 - 80 90 - 300
1010, 1020, 1025, 1522, 1144, etc.
40 - 70
80 - 200
Medium-Carbon Steel
60 - 80 90 - 300
B
1030, 1040, 1050, 1527, 1140, 1151, etc. 180 - 325 6 - 10
40 - 70 40 - 70
80 - 200 80 - 200
Alloy Steel
125 - 180 6 - 10
P
4140, 5140, 8640, etc. High-Strength Alloy 4340, 4330V, 300M, etc. Structural Steel
180 - 375
4 - 8
30 - 50 60 - 150 15 - 30 60 - 120
BORING
240 - 450 3 - 6
125 - 180
7 - 15
60 - 80 90 - 300
A36, A285, A516
180 - 350 6 - 10
40 - 70
80 - 200
Tool Steel
150 - 200
7 - 15
60 - 80 90 - 300
H-13, H-21, A-4, 0-2, S-3, etc.
200 - 250 6 - 10
40 - 70
80 - 200
High-Temp Alloy
140 - 310 4 - 10 30 - 50
-
0.15 - 0.30
-
0.20 - 0.40
-
0.30 - 0.50
-
S
Hastelloy B, Inconel 600, etc. Titanium Alloy Stainless Steel 400 Series 416, 420, etc. Stainless Steel 300 Series 304, 316, 17-4PH, etc. Grey Cast Iron, Ductile Cast Iron, Spheroidal Cast Iron (Pearlitic) Spheroidal Cast Iron (Ferritic)
140 - 310 4 - 15 30 - 50
-
0.15 - 0.30
-
0.20 - 0.40
-
0.30 - 0.50
-
C
135 - 350 4 - 10 30 - 50 60 - 150
0.20 - 0.40 0.30 - 0.50 0.30 - 0.60 0.30 - 0.80 0.40 - 0.70 0.40 - 1.00
REAMING M
135 - 275
4 - 10 30 - 50 60 - 150
0.20 - 0.40 0.30 - 0.50 0.30 - 0.60 0.30 - 0.80 0.40 - 0.70 0.40 - 1.00
< 200 15 - 30 > 200 10 - 20
50 - 70 50 - 70
- -
0.20 - 0.40 0.30 - 0.60 0.35 - 0.60 0.50 - 0.80 0.40 - 1.00 0.60 - 1.50 0.20 - 0.40 0.30 - 0.60 0.35 - 0.60 0.50 - 0.80 0.40 - 1.00 0.60 - 1.50 0.20 - 0.40 0.30 - 0.60 0.35 - 0.60 0.50 - 0.80 0.40 - 1.00 0.60 - 1.50
K
260 - 320 8 - 12 30 - 50 60 - 120
Copper and Alloys
< 500 10 - 18 100 - 200
-
0.20 - 0.40
-
0.40 - 0.70
-
0.50 - 0.80
-
Brass Bronze
N
< 180 10 - 20 80 - 160 100 - 300 0.15 - 0.30
-
0.20 - 0.40
-
0.30 - 0.60
-
D
Bronze Phosphorous Aluminum and Alloys
< 150 15 - 30 100 - 200
-
0.20 - 0.40
-
0.40 - 0.70
-
0.50 - 0.80
-
BURNISHING
Formulas 1. RPM = m/min • 3.82 • DIA
2. mm/min = RPM • mm/rev
3. m/min = RPM • 0.003 • DIA
where:
where:
where:
RPM
= revoluƟons per minute (rev/min)
mm/min = mm per minute (mm/min)
m/min = speed (m/min)
m/min = speed (m/min)
RPM
= revoluƟons per minute (rev/min)
RPM
= revoluƟons per minute (rev/min)
DIA
= diameter of reamer (mm)
mm/rev = feed rate (mm/rev)
DIA
= diameter of reamer (mm)
E
THREADING
X
SPECIALS
IMPORTANT: The speeds and feeds listed on these pages are a general starƟng point for all applicaƟons. Factory technical assistance is also available for specific applicaƟons through our ApplicaƟon Engineering department. email: engineering.eu@alliedmachine.com
C: 74
www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com
Made with FlippingBook Ebook Creator