A50-APX_US-EN

The APX Drill deep hole / large diameter drilling system is designed to perform high-performance operations on low horse powered CNC machines. The drill body connects with with a T-A® style pilot head or GEN3SYS® style pilot head, utilizing the benefits and key performances of Allied Machine's product capabilities.

Boring

Reaming

Burnishing

Threading

APX ™ Drill DRILLING Deep Hole / Large Diameter Drilling System

Specials

S E C T I O N A50 APX ™ Drill

APX ™ Drill Deep Hole / Large Diameter Drilling System Diameter Range: 1.299" - 4.000" (33.00 mm - 101.60 mm)

Your safety and the safety of others is very important. This catalog contains important safety messages. Always read and follow all safety precautions. This triangle is a safety hazard symbol. It alerts you to potential safety hazards that can cause tool failure and serious injury. When you see this symbol in the catalog, look for a related safety message that may be near this triangle or referred to in the nearby text. There are safety signal words also used in the catalog. Safety messages follow these words. WARNING WARNING (shown above) means that failure to follow the precautions in this message could result in tool failure and serious injury. NOTICE means that failure to follow the precautions in this message could result in damage to the tool or machine but not result in personal injury. NOTE and IMPORTANT are also used. These are important that you read and follow but are not safety-related. Visit www.alliedmachine.com for the most up-to-date information and procedures.

Don’t Let Your Machine Slow You Down The APX deep hole/large diameter drilling system delivers the strength and versatility needed for any deep hole drilling application. The breakthrough geometry is designed to increase penetration rates and tool life. By allowing for higher spindle speeds, the APX lets you take advantage of the power curve on modern CNC machines.

Improves hole quality and surface finish

Provides maximum durability and stability

Excellent chip control

Applicable Industries

Aerospace Agriculture

Automotive

Firearms

General Machining

Oil & Gas

Renewable Energy

APX ™ Drill Contents

Reference Icons The following icons will appear throughout the catalog to help you navigate between products.

Introduction Information Drill Selection Guide / Assembly Details . . . . . . . . . . . . . . . 2 - 3 Pilot Insert Options / Details . . . . . . . . . . . . . . . . . 4 Product Nomenclature . . . . . . . . . . . . . . . . . 5

Setup / Assembly Information Detailed instructions and information regarding the corresponding part(s)

Recommended Cutting Data Speed and feed recommendations for optimum and safe drilling

Drill Series 33 Series . . . . . . . . . . . . . . . . 6 - 7 38 Series . . . . . . . . . . . . . . . . 8 - 9 44 Series . . . . . . . . . . . . . . 10 - 11 51 Series . . . . . . . . . . . . . . 12 - 13 57 Series . . . . . . . . . . . . . . 14 - 15 63 Series . . . . . . . . . . . . . . 16 - 17 70 Series . . . . . . . . . . . . . . 18 - 19 76 Series . . . . . . . . . . . . . . 20 - 21 83 Series . . . . . . . . . . . . . . 22 - 23 89 Series . . . . . . . . . . . . . . 24 - 25 95 Series . . . . . . . . . . . . . . 26 - 27

GEN3SYS® Pilot Inserts Lists the GEN3SYS XT Pro pilot ISO insert options for each APX drill series

T-A® Pilot Inserts Lists the T-A® and GEN2 T-A® pilot insert options for each APX Drill series

Coolant-Through Option Indicates that the product is coolant through

Recommended Cutting Data

Imperial (inch) . . . . . . . . . . . . . . . . . 28 Metric (mm) . . . . . . . . . . . . . . . . . 29 Deep Hole Drilling Guidelines . . . . . . . . . . . . . . . . . 30

Diameter Range

Series

Imperial (inch) 1.299 - 1.496 1.496 - 1.732 1.732 - 2.008 2.008 - 2.244 2.244 - 2.480 2.480 - 2.756 2.756 - 2.992 2.992 - 3.268 3.268 - 3.504 3.504 - 3.740 3.740 - 4.000

Metric (mm) 33.00 - 37.99 38.00 - 43.99 44.00 - 50.99 51.00 - 56.99 57.00 - 62.99 63.00 - 69.99 70.00 - 75.99 76.00 - 82.99 83.00 - 88.99 89.00 - 94.99 95.00 - 101.60

33 38 44 51 57 63 70 76 83 89 95

A50: 1

DRILLING | APX™ Drill: Deep Hole / Large Diameter Replaceable Insert Drilling System

Drill Selection Guide

A

Series

33

38

44

51

57

DRILLING

Page

6 - 7

8 - 9

10 - 11

12 - 13

14 - 15

B

D 5 inch D 5 mm

1.299 - 1.496 33.00 - 37.99

1.496 - 1.732 38.00 - 43.99

1.732 - 2.008 44.00 - 50.99

2.008 - 2.244 51.00 - 56.99

2.244 - 2.480 57.00 - 62.99

BORING

P M K N S H

P M K N S H

P M K N S H

P M K N S H

P M K N S H

ISO Material

IC Insert Shape

IC Insert Size (inch) IC Insert Size (mm)

5/16"

3/8" 9.53

3/8", 1/2" 9.53, 12.70

1/2", 9/16" 12.70, 14.29

9/16" 14.29

7.94

C

Wear Pads

NO

NO

NO

NO

NO

Holders Drill Depth (inch) Drill Depth (mm)

REAMING

4-7/16 - 14-29/32

5-1/8 - 17-1/4 130.5 - 439.9

6 - 20-1/8

6-3/8 - 22-3/8 161.8 - 570.0

7-1/8 - 24-3/4 179.9 - 626.9

112.6 - 378.6

151.5 - 510.0

Pilot Insert T-A Series

0, 1

0, 1

1

1

1, 2

GEN3SYS XT Pro Series

-

15, 17, 18, 20

17, 18, 22

18, 20, 22

22, 24, 26

T-A® Style Pilot Insert Head • Utilizes both T-A Pro and T-A inserts (0 - 2 series) • Multiple geometry options are available to achieve optimal results in different types of applications

GEN3SYS® XT Style Pilot Insert Head • Utilizes GEN3SYS XT Pro inserts (15 - 32 series) • ISO geometry options are available to achieve optimal results in different types of applications

D

BURNISHING

Insert Application Recommendations Carbide Grade Options C5 (P35)

General purpose carbide grade suitable for most applications. Common application in steels and stainless steels.

E

C1 (K35)

Toughest carbide grade. Provides the best combination of edge strength and tool life. Recommended for less rigid applications. Higher wear-resistant carbide suitable for abrasive material applications. Recommended for grey, ductile, and nodular irons.

IC Insert AM300® • The design allows for excellent chip control and aggressive penetration rates • The proprietary AM300 coatings increase tool life above competitors’ premium coatings

THREADING

C2 (K25)

Additional Geometry Option High Rake (HR)

Provides superior chip control and tool life in long-chipping carbon and alloy steels below 200 Bhn.

X

SPECIALS

Flanged Straight Shank

CAT40 / CAT50 Integral Shank

A50: 2

www.alliedmachine.com | 1.330.343.4283

DRILLING | APX™ Drill: Deep Hole / Large Diameter Replaceable Insert Drilling System

A

63

70

76

83

89

95

DRILLING

16 - 17

18 - 19

20 - 21

22 - 23

24 - 25

26 - 27

B

2.480 - 2.756 63.00 - 69.99

2.756 - 2.992 70.00 - 75.99

2.992 - 3.268 76.00 - 82.99

3.268 - 3.504 83.00 - 88.99

3.504 - 3.740 89.00 - 94.99

3.740 - 4.000 95.00 - 101.60

BORING

P M K N S H

P M K N S H

P M K N S H

P M K N S H

P M K N S H

P M K N S H

9/16" 14.29

3/8" 9.53

1/2"

1/2"

9/16" 14.29

9/16" 14.29

12.70

12.70

C

NO

YES

YES

YES

YES

YES

REAMING

7-7/8 - 27-1/8 200.8 - 688.3

8-3/4 - 27-7/8 218.8 - 709.4

9-1/2 - 26-1/8 239.9 - 664.0

10-1/8 - 27-3/4 257.8 - 704.9

10-7/8 - 27-5/8 275.8 - 701.8

11-7/8 - 27-1/2 302.0 - 698.5

2

2

2

2

2

2

26, 29, 32

29

29

32

29

32

A

D

B

BURNISHING

ASSEMBLY

E

THREADING

Step 1: Lower the APX head assembly onto the APX holder.

Step 2: Insert the head mounting screws into points A and B. Tighten until the head is properly secured to the holder.

Step 3: Tighten with the head mounting driver using the torque setting chart below.

Torque Setting Chart

X

Series

Screw

Driver

Torque

33 - 63

75020-IP20-1

8IP-20

60 in-lb (678 N-cm)

SPECIALS

70 - 95

78027-IP30-1

8IP-30B

250 in-lb (2825 N-cm)

www.alliedmachine.com | 1.330.343.4283

A50: 3

DRILLING | APX™ Drill: Deep Hole / Large Diameter Replaceable Insert Drilling System

Pilot Insert Options

A

T-A® Pilot Inserts

T-A Tiny Chip (-TC) • Unique lip and point design for excellent chip control • Improved capabilities in long-chipping materials such as low-carbon steels and soft alloy steels • Enhanced performance in lower-powered machines for better chip formation at lower feed rates T-A High Impact (-HI) • Designed to enhance chip formation in materials with high elasticity/ductility and poor chip forming characteristics • SK2 corner preparation for increased tool life • Improves chip formation in structural, cast, and forged steels

DRILLING

B

BORING

T-A Pro P - Steels • Designed to provide increased penetration rates and tool life in steel applications • Superior geometry and edge provides excellent chip control • Allied’s multilayer AM300® coating increases heat resistance and improves tool life T-A Pro K - Cast Irons • Uniquely designed for cast/ductile iron applications • Geometry developed for maximum tool life, reduced exit burr, and improved hole finish • Allied’s multilayer TiAlN coating provides increased abrasion resistance and tool life T-A Pro N - Nonferrous Materials • Designed for applications in aluminum, brass, and copper • The geometry yields excellent chip control in these softer materials • TiCN coating gives the versatility to run in a variety of materials while reducing buildup T-A Pro M - Stainless Steel • Designed for all stainless steels and heat-resistant super alloys • Geometry optimized for improved chip formation while minimizing exit burr • Allied’s new AM460 coating provides industry leading tool life in stainless and HRSA materials T-A Pro X - High-Speed Steel Materials • Improved chip geometry for excellent chip control in all materials • Long tool life and high-process security for the most challenging applications • Allied’s multilayer AM200® coating combines excellent heat resistance and high lubricity for wide application use T-A Standard • Excellent choice for general purpose use • Provides fast penetration rates that produce good hole size and finish • Combines highly efficient, stable cutting action to minimize power consumption

GEN3SYS® XT Pro Pilot Inserts

P

C

REAMING

K

P - Steels • Designed to provide increased penetration rates and tool life in steel applications • Superior geometry and edge provides excellent chip control • Allied’s multilayer AM420 coating increases heat resistance and improves tool life K - Cast Irons • Uniquely designed for cast/nodular iron applications • Geometry includes a corner radius for improved hole finish and heat dispersion • Allied’s multilayer AM440 coating provides increased abrasion resistance and tool life N - Nonferrous Materials • Designed for applications in aluminum, brass, and copper • The geometry yields excellent chip control in these softer materials • TiN coating gives the versatility to run in a variety of materials while reducing buildup

D

BURNISHING

N

P

E

M

K

THREADING

X

N

X

NOTE: For a complete offering of pilot inserts, see sections A20 (GEN3SYS Drilling Systems), A25 (T-A Pro Drilling Systems) and A30 (T-A Drilling Systems) of our catalog.

SPECIALS

A50: 4

www.alliedmachine.com | 1.330.343.4283

DRILLING | APX™ Drill: Deep Hole / Large Diameter Replaceable Insert Drilling System

Product Nomenclature

A

APX Drill Heads

DRILLING

V 38

15

D - 0116

1

2

3

4

5

1. APX Head

2. Series

3. Pilot Series

V = Head

33 = 33 series 38 = 38 series 44 = 44 series 51 = 51 series 57 = 57 series 63 = 63 series

70 = 70 series 76 = 76 series 83 = 83 series 89 = 89 series 95 = 95 series

T-A® Pilot Insert

GEN3SYS® XT Pro Pilot Insert

B

00 = 0 series 01 = 1 series 02 = 2 series

15 = 15 series 17 = 17 series 18 = 18 series 20 = 20 series 22 = 22 series

24 = 24 series 26 = 26 series 29 = 29 series 32 = 32 series

BORING

Ordering Nonstocked Diameters:

4. Effective Cutting

5. Major Diameter

D = Double effective S = Single effective

0116 = Inch

Non-stocked diameters are also available. Please refer to the price list for applicable process fees. Follow the ordering examples below:

C

1.5153 = Decimal 68 = Metric

• Inch: 38 series, T-A (1 series), 1.6790" = V3801D-1.6790 • Metric: 38 series, T-A (1 series), 42.15 mm = V3801D-42.15

REAMING

APX Drill Holders

W 38

05

H - 200F

1

2

3

4

5

D

1. APX Holder

2. Series

3. Drill Length

4. Flute Style

5. Shank

BURNISHING

W = Holder

33 = 33 series 38 = 38 series 44 = 44 series 51 = 51 series 57 = 57 series 63 = 63 series

70 = 70 series 76 = 76 series 83 = 83 series 89 = 89 series 95 = 95 series

03 = 3xD 05 = 5xD 08 = 8xD 10 = 10xD

H = Helical

150F = 1-1/2" flanged straight shank 200F = 2" flanged straight shank 40FM = 40mm flanged straight shank 50FM = 50mm flanged straight shank

CV40 = CAT40 integral shank CV50 = CAT50 integral shank

E

D 5

THREADING

L 1

L 3

L 7

D 5 D 1

D 2

D 5

P 1

L 2

L 9

Reference Key Symbol

Reference Key Symbol Attribute

X

Attribute

Symbol Attribute

D 1 D 5

D 2 D 5

L 3 L 7 P 1

Pilot insert diameter Major cutting diameter

Shank diameter

Holder reference length

SPECIALS

Drill diameter range

Shank length Rear pipe tap

L 9

Pilot insert length

L 1 L 2

Overall length

Drill depth

www.alliedmachine.com | 1.330.343.4283

A50: 5

33

DRILLING | APX™ Drill: Deep Hole / Large Diameter Replaceable Insert Drilling System

APX Drill Heads

A

33 Series | Diameter Range: 1.299" - 1.496" (33.00 mm - 37.99 mm)

D 5

DRILLING

D 5 D 1

B

L 9

T-A® Head

Heads

BORING

Head

T-A Head

IC Insert Size

D 5 fractional

D 5 inch

D 5 metric 33.00 33.34 34.00 34.13 34.93 35.00 35.72 36.00 36.51 37.00 37.31

Part No.

Pilot Series

T-A Pro Insert

T-A (-TC) Insert 1C10H-16-TC 1C10H-16-TC 1C11H-18-TC 1C11H-18-TC 1C11H-18-TC 1C11H-18-TC 1C11H-18-TC 1C11H-20-TC 1C11H-20-TC 1C11H-20-TC 1C11H-20-TC

inch metric

D 1 16 16 18 18 18 18 18 20 20 20 20

L 9

V3300D-33

-

1.299

1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4

0 0 1 1 1 1 1 1 1 1 1

TA#0-16.00 TA#0-16.00 TA#1-18.00 TA#1-18.00 TA#1-18.00 TA#1-18.00 TA#1-18.00 TA#1-20.00 TA#1-20.00 TA#1-20.00 TA#1-20.00

5/16 5/16 5/16 5/16 5/16 5/16 5/16 5/16 5/16 5/16 5/16

7.94 7.94 7.94 7.94 7.94 7.94 7.94 7.94 7.94 7.94 7.94

V3300D-0110

1-5/16 1.313

V3301D-34

-

1.339

C

V3301D-0111 V3301D-0112

1-11/32 1.344

1-3/8

1.375 1.378

V3301D-35

-

REAMING

V3301D-0113

1-13/32 1.406

V3301D-36

-

1.417

V3301D-0114

1-7/16 1.438

V3301D-37

-

1.457

V3301D-0115

1-15/32 1.469

#Denotes ISO material/geometry (P= steel, K= cast iron, N= nonferrous)

IC Inserts

D

Size

BURNISHING

Admissible Tightening Torque* 27.0 in-lbs (305 N-cm) 27.0 in-lbs (305 N-cm) 27.0 in-lbs (305 N-cm) 27.0 in-lbs (305 N-cm)

Coating inch metric AM300® 5/16 7.94 C5 (P35) AM300® 5/16 7.94 C1 (K35) AM300® 5/16 7.94 C2 (K25) AM300® 5/16 7.94 C5 (P35)

Grade Geometry

Part No.

Insert Screw

Insert Driver

OP-05T308-PW OP-05T308-1PW OP-05T308-2PW OP-05T308-PWHR

Standard Standard Standard High Rake

IS-10-1 IS-10-1 IS-10-1 IS-10-1

8IP-10 8IP-10 8IP-10 8IP-10

*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength

E

Pilot Accessories

Admissible Tightening Torque* 15.5 in-lbs (175 N-cm) 27.0 in-lbs (305 N-cm)

THREADING

Pilot Style

Series

Insert Screws 72567-IP8-1

Insert Driver

T-A T-A

0 1

8IP-8 8IP-9

7375-IP9-1

*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength

X

Nonstocked diameters are also available. Follow the examples shown below. Inch 38 series, T-A (1 series), 1.6790" Part No. = V3801D-1.6790 Metric 38 series, T-A (1 series), 42.15 mm Part No. = V3801D-42.15

A50: 28 - 29

A50: 2 - 5

Section A25 & A30

SPECIALS

Key on A50: 1

IC inserts sold in multiples of 2 | Insert screws sold in multiples of 10

A50: 6

www.alliedmachine.com | 1.330.343.4283

DRILLING | APX™ Drill: Deep Hole / Large Diameter Replaceable Insert Drilling System

33

APX Drill Holders 33 Series | Diameter Range: 1.299" - 1.496" (33.00 mm - 37.99 mm)

A

DRILLING

L 1

L 3

L 7

D 2

D 5

P 1

L 2

B

Straight Shank

Body

Shank

BORING

Length

Part No.

D 5

L 2

L 3

L 1

L 7

D 2

P 1

W3303H-150F W3305H-150F W3308H-150F W3310H-150F W3303H-40FM W3305H-40FM W3308H-40FM W3310H-40FM

3xD 5xD 8xD

1.299 - 1.496 1.299 - 1.496 1.299 - 1.496 1.299 - 1.496 33.00 - 37.99 33.00 - 37.99 33.00 - 37.99 33.00 - 37.99

4-7/16 7-27/64 11-59/64 14-29/32

6-19/32 9-37/64 14-5/64 17-1/16 167.49 243.41 357.40 433.40

9-9/32 12-9/32 16-3/4 19-3/4 237.49 313.41 427.40 503.40

2-11/16 2-11/16 2-11/16 2-11/16

1-1/2 1-1/2 1-1/2 1-1/2 40.00 40.00 40.00 40.00

1/4 NPT 1/4 NPT 1/4 NPT 1/4 NPT 1/4 BSPT 1/4 BSPT 1/4 BSPT 1/4 BSPT

10xD

3xD 5xD 8xD

112.60 188.60 302.60 378.61

70.00 70.00 70.00 70.00

C

10xD

REAMING

L 1

L 3

D 5

D

L 2

BURNISHING

CAT Integral Shank

Body

D 5

Length

inch

mm

Shank CV40 CV40 CV40 CV40 CV50 CV50 CV50 CV50

Part No.

L 2

L 3

L 1

W3303H-CV40 W3305H-CV40 W3308H-CV40 W3310H-CV40 W3303H-CV50 W3305H-CV50 W3308H-CV50 W3310H-CV50

3xD 5xD 8xD 3xD 5xD 8xD 10xD 10xD

1.299 - 1.496 1.299 - 1.496 1.299 - 1.496 1.299 - 1.496 1.299 - 1.496 1.299 - 1.496 1.299 - 1.496 1.299 - 1.496

33.00 - 37.99 33.00 - 37.99 33.00 - 37.99 33.00 - 37.99 33.00 - 37.99 33.00 - 37.99 33.00 - 37.99 33.00 - 37.99

4-7/16 7-27/64 11-59/64 14-29/32 4-7/16 7-27/64 11-59/64 14-29/32

7-3/8

10-3/16 13-11/64 17-21/32 20-21/32 14-31/64 18-31/32 21-31/32 11-1/2

10-23/64 14-55/64 17-27/32 10-23/64 14-55/64 17-27/32 7-3/8

E

THREADING

Connection Accessories

Mounting Screw

Mounting Screw Driver

Admissible Tightening Torque*

X

75020-IP20-1

8IP-20

60 in-lb (678 N-cm)

*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength

SPECIALS

Refer to Speed and Feed charts for recommended adjustments to speeds and feeds. Refer to page A50: 30 for deep hole drilling guidelines in this section of the catalog. Visit www.alliedmachine.com/DeepHoleGuidelines for the most up-to-date information and procedures. Factory technical assistance is available for your specific applications through our Application Engineering Team. ext: 7611 | email: appeng@alliedmachine.com WARNING

Mounting screws sold in multiples of 4 = Imperial (in) = Metric (mm)

www.alliedmachine.com | 1.330.343.4283

A50: 7

38

DRILLING | APX™ Drill: Deep Hole / Large Diameter Replaceable Insert Drilling System

APX Drill Heads

A

38 Series | Diameter Range: 1.496" - 1.732" (38.00 mm - 43.99 mm)

D 5

DRILLING

D 5

D 5 D 1

D 5

D 1

B

L 9

L 9

T-A® Head

GEN3SYS® XT Pro Head

Heads

BORING

Head

T-A Head

GEN3SYS XT Pro Head

IC Insert Size

Pilot Series T-A Pro Insert T-A (-TC) Insert 0 TA#0-15.88 1C10H-0020-TC 0 TA#0-15.88 1C10H-0020-TC 0 TA#0-15.88 1C10H-0020-TC 0 TA#0-15.88 1C10H-0020-TC 0 TA#0-15.88 1C10H-0020-TC 0 TA#0-17.46 1C10H-0022-TC 0 TA#0-17.46 1C10H-0022-TC 0 TA#0-17.46 1C10H-0022-TC 0 TA#0-17.46 1C10H-0022-TC 1 TA#1-19.05 1C11H-0024-TC 1 TA#1-19.05 1C11H-0024-TC 1 TA#1-19.05 1C11H-0024-TC 1 TA#1-20.64 1C11H-0026-TC 1 TA#1-20.64 1C11H-0026-TC

D 5 fractional

D 5 inch

D 5 metric

Pilot Series Pilot Insert

Part No.

Part No.

inch metric

D 1

L 9

V3800D-38

V3815D-38

-

1.496 38.00 5/8 19/64

15 XT#15-15.88 3/8 9.53 15 XT#15-15.88 3/8 9.53 15 XT#15-15.88 3/8 9.53 15 XT#15-15.88 3/8 9.53 15 XT#15-15.88 3/8 9.53 17 XT#17-17.46 3/8 9.53 17 XT#17-17.46 3/8 9.53 17 XT#17-17.46 3/8 9.53 17 XT#17-17.46 3/8 9.53 18 XT#18-19.05 3/8 9.53 18 XT#18-19.05 3/8 9.53 18 XT#18-19.05 3/8 9.53 20 XT#20-20.64 3/8 9.53 20 XT#20-20.64 3/8 9.53

1-1/2 1.500 38.10 5/8 19/64 V3800D-0116 1-17/32 1.531 38.90 5/8 19/64 V3800D-0117

V3815D-0116 V3815D-0117

C

V3800D-39

V3815D-39

-

1.535 39.00 5/8 19/64

1-9/16 1.563 39.69 5/8 19/64 V3800D-0118

V3815D-0118

V3800D-40

V3817D-40

-

1.575 40.00 11/16 19/64

REAMING

1-19/32 1.594 40.48 11/16 19/64 V3800D-0119

V3817D-0119

V3800D-41

V3817D-41

-

1.614 41.00 11/16 19/64

1-5/8 1.625 41.28 11/16 19/64 V3800D-0120

V3817D-0120

V3801D-42

V3818D-42

-

1.654 42.00 3/4 19/64

1-21/32 1.656 42.07 3/4 19/64 V3801D-0121 1-11/16 1.688 42.86 3/4 19/64 V3801D-0122

V3818D-0121 V3818D-0122

V3801D-43

V3820D-43

-

1.693 43.00 13/16 19/64

1-23/32 1.719 43.66 13/16 19/64 V3801D-0123

V3820D-0123

#Denotes ISO material/geometry (P= steel, K= cast iron, N= nonferrous)

D

IC Inserts BURNISHING

Size

Admissible Tightening Torque* 41.0 in-lbs (465 N-cm) 41.0 in-lbs (465 N-cm) 41.0 in-lbs (465 N-cm) 41.0 in-lbs (465 N-cm)

Coating

inch metric

Grade Geometry

Part No.

Insert Screw 73595-IP15-1 73595-IP15-1 73595-IP15-1 73595-IP15-1

Insert Driver

OP-060408-PW OP-060408-1PW OP-060408-2PW OP-060408-PWHR

AM300® 3/8 AM300® 3/8 AM300® 3/8 AM300® 3/8

9.53 C5 (P35) 9.53 C1 (K35) 9.53 C2 (K25) 9.53 C5 (P35)

Standard Standard Standard High Rake

8IP-15 8IP-15 8IP-15 8IP-15

*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength

E

Pilot Accessories

THREADING

Admissible Tightening Torque* 15.5 in-lbs (175 N-cm) 27.0 in-lbs (305 N-cm) 7.4 in-lbs (84 N-cm) 15.5 in-lbs (175 N-cm) 27.0 in-lbs (305 N-cm) 27.0 in-lbs (305 N-cm)

Pilot Style

Series

Insert Screws 72567-IP8-1 7375-IP9-1 7247-IP7-1 72567-IP8-1 7375-IP9-1 7375-IP9-1

Insert Driver

T-A T-A

0 1

8IP-8 8IP-9 8IP-7 8IP-8 8IP-9 8IP-9

GEN3SYS GEN3SYS GEN3SYS GEN3SYS

15 17 18 20

X

*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength

Nonstocked diameters are also available. Follow the examples shown below. Inch 38 series, T-A (1 series), 1.6790" Part No. = V3801D-1.6790 Metric 38 series, T-A (1 series), 42.15 mm Part No. = V3801D-42.15

A50: 28 - 29

A50: 2 - 5

Section A20 Section A25 & A30

SPECIALS

Key on A50: 1

IC inserts sold in multiples of 2 | Insert screws sold in multiples of 10

A50: 8

www.alliedmachine.com | 1.330.343.4283

DRILLING | APX™ Drill: Deep Hole / Large Diameter Replaceable Insert Drilling System

38

APX Drill Holders 38 Series | Diameter Range: 1.496" - 1.732" (38.00 mm - 43.99 mm)

A

L 1

DRILLING

L 3

L 7

D 2

D 5

P 1

L 2

Straight Shank

B

Body

Shank

Length

Part No.

D 5

L 2

L 3

L 1

L 7

D 2

P 1

W3803H-150F W3805H-150F W3808H-150F W3810H-150F W3803H-200F W3805H-200F W3808H-200F W3810H-200F W3803H-40FM W3805H-40FM W3808H-40FM W3810H-40FM W3803H-50FM W3805H-50FM W3808H-50FM W3810H-50FM

3xD 5xD 8xD 3xD 5xD 8xD 10xD 10xD 3xD 5xD 8xD 3xD 5xD 8xD 10xD 10xD

1.496 - 1.732 1.496 - 1.732 1.496 - 1.732 1.496 - 1.732 1.496 - 1.732 1.496 - 1.732 1.496 - 1.732 1.496 - 1.732 38.00 - 43.99 38.00 - 43.99 38.00 - 43.99 38.00 - 43.99 38.00 - 43.99 38.00 - 43.99 38.00 - 43.99 38.00 - 43.99

5-1/8 8-5/8

7-47/64 11-13/64 16-25/64 19-27/32 7-47/64 11-13/64 16-25/64 19-27/32

10-25/64 13-55/64 19-3/64 22-33/64 12-15/64 15-45/64 20-57/64 24-59/64

2-11/16 2-11/16 2-11/16 2-11/16

1-1/2 1-1/2 1-1/2 1-1/2

1/4 NPT 1/4 NPT 1/4 NPT 1/4 NPT 1/4 NPT 1/4 NPT 1/4 NPT 1/4 NPT 1/4 BSPT 1/4 BSPT 1/4 BSPT 1/4 BSPT 1/4 BSPT 1/4 BSPT 1/4 BSPT 1/4 BSPT

BORING

13-7/8 17-1/4

5-1/8 8-5/8

4-1/2 4-1/2 4-1/2 4-1/2 70.00 70.00 70.00 70.00 80.00 80.00 80.00 80.00

2 2 2 2

13-7/8 17-1/4 130.51 219.99 351.99 439.90 130.51 219.99 351.99 439.90

C

196.49 284.51 416.51 503.91 196.49 284.51 416.51 503.90

265.71 353.70 485.70 573.71 276.50 364.49 496.99 583.91

40.00 40.00 40.00 40.00 50.00 50.00 50.00 50.00

REAMING

L 1

L 3

D

BURNISHING

D 5

L 2

CAT Integral Shank

Body

D 5

Length

inch

mm

Shank CV40 CV40 CV40 CV40 CV50 CV50 CV50 CV50

Part No.

L 2

L 3

L 1

W3803H-CV40 W3805H-CV40 W3808H-CV40 W3810H-CV40 W3803H-CV50 W3805H-CV50 W3808H-CV50 W3810H-CV50

3xD 5xD 8xD 3xD 5xD 8xD 10xD 10xD

1.496 - 1.732 1.496 - 1.732 1.496 - 1.732 1.496 - 1.732 1.496 - 1.732 1.496 - 1.732 1.496 - 1.732 1.496 - 1.732

38.00 - 43.99 38.00 - 43.99 38.00 - 43.99 38.00 - 43.99 38.00 - 43.99 38.00 - 43.99 38.00 - 43.99 38.00 - 43.99

5-1/8 8-5/8

8-5/16

11

E

11-49/64 16-31/32 20-7/16 11-49/64 16-31/32 20-7/16 8-5/16

14-29/64 19-21/32 23-1/8 12-5/16 15-49/64 20-31/32 24-7/16

13-7/8 17-1/4

THREADING

5-1/8 8-5/8

13-7/8 17-1/4

Connection Accessories

X

Mounting Screw

Mounting Screw Driver

Admissible Tightening Torque*

75020-IP20-1

8IP-20

60 in-lb (678 N-cm)

*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength

SPECIALS

Refer to Speed and Feed charts for recommended adjustments to speeds and feeds. Refer to page A50: 30 for deep hole drilling guidelines in this section of the catalog. Visit www.alliedmachine.com/DeepHoleGuidelines for the most up-to-date information and procedures. Factory technical assistance is available for your specific applications through our Application Engineering Team. ext: 7611 | email: appeng@alliedmachine.com WARNING

Mounting screws sold in multiples of 4 = Imperial (in) = Metric (mm)

www.alliedmachine.com | 1.330.343.4283

A50: 9

44

DRILLING | APX™ Drill: Deep Hole / Large Diameter Replaceable Insert Drilling System

APX Drill Heads

A

44 Series | Diameter Range: 1.732" - 2.008" (44.00 mm - 50.99 mm)

D 5

DRILLING

D 5

D 5 D 1

D 5

D 1

B

L 9

L 9

T-A® Head

GEN3SYS® XT Pro Head

Heads

BORING

Head

T-A Head

GEN3SYS XT Pro Head

IC Insert Size

D 5 fractional

D 5 inch

D 5 metric

Pilot Series T-A Pro Insert T-A (-TC) Insert 1 TA#1-22.23 1C11H-0028-TC

Pilot Series Pilot Insert

D 1

L 9

Part No.

Part No.

inch metric

V4401D-44

V4422D-44

-

1.732 44.00 7/8 21/64

22 XT#22-22.23 3/8 9.53 22 XT#22-22.23 3/8 9.53 22 XT#22-22.23 3/8 9.53 22 XT#22-22.23 3/8 9.53 22 XT#22-23.81 3/8 9.53 22 XT#22-23.81 3/8 9.53 22 XT#22-23.81 3/8 9.53 22 XT#22-23.81 3/8 9.53 22 XT#22-23.81 3/8 9.53 17 XT#17-17.86 1/2 12.70 17 XT#17-17.86 1/2 12.70 17 XT#17-17.86 1/2 12.70 17 XT#17-17.86 1/2 12.70 18 XT#18-18.65 1/2 12.70 18 XT#18-18.65 1/2 12.70 18 XT#18-18.65 1/2 12.70

1-3/4 1.750 44.45 7/8 21/64 V4401D-0124

1 TA#1-22.23 1C11H-0028-TC V4422D-0124

V4401D-45

V4422D-45

-

1.772 45.00 7/8 21/64

1 TA#1-22.23 1C11H-0028-TC

1-25/32 1.781 45.25 7/8 21/64 V4401D-0125

1 TA#1-22.23 1C11H-0028-TC V4422D-0125

C

V4401D-46

V4422D-46

-

1.811 46.00 15/16 21/64

1 TA#1-23.81 1C11H-0030-TC

1-13/16 1.813 46.04 15/16 21/64 V4401D-0126 1-27/32 1.844 46.83 15/16 21/64 V4401D-0127

1 TA#1-23.81 1C11H-0030-TC V4422D-0126 1 TA#1-23.81 1C11H-0030-TC V4422D-0127

REAMING

V4401D-47

V4422D-47

-

1.850 47.00 15/16 21/64

1 TA#1-23.81 1C11H-0030-TC

1-7/8 1.875 47.63 15/16 21/64 V4401D-0128

1 TA#1-23.81 1C11H-0030-TC V4422D-0128

V4401D-48

V4417D-48 V4417D-0129 V4417D-49 V4417D-0130 V4418D-50 V4418D-0131 V4418D-0200

-

1.890 48.00 45/64 21/64

1** TA#1-17.86 1C11H-.703-TC 1** TA#1-17.86 1C11H-.703-TC 1** TA#1-17.86 1C11H-.703-TC 1** TA#1-17.86 1C11H-.703-TC 1** TA#1-18.65 1C11H-.734-TC 1** TA#1-18.65 1C11H-.734-TC 1** TA#1-18.65 1C11H-.734-TC

1-29/32 1.906 48.42 45/64 21/64 V4401D-0129

V4401D-49

-

1.929 49.00 45/64 21/64

1-15/16 1.938 49.21 45/64 21/64 V4401D-0130

V4401D-50

-

1.969 50.00 47/64 21/64

1-31/32 1.969 50.01 47/64 21/64 V4401D-0131 2.000 50.80 47/64 21/64 V4401D-0200 2

D

#Denotes ISO material/geometry (P= steel, K= cast iron, N= nonferrous)

IC Inserts

BURNISHING

Size

Admissible Tightening Torque* 41.0 in-lbs (465 N-cm) 41.0 in-lbs (465 N-cm) 41.0 in-lbs (465 N-cm) 41.0 in-lbs (465 N-cm) 61.0 in-lbs (690 N-cm) 61.0 in-lbs (690 N-cm) 61.0 in-lbs (690 N-cm) 61.0 in-lbs (690 N-cm)

Coating inch metric AM300® 3/8 9.53 C5 (P35) Standard AM300® 3/8 9.53 C1 (K35) Standard AM300® 3/8 9.53 C2 (K25) Standard AM300® 3/8 9.53 C5 (P35) High Rake AM300® 1/2 12.70 C5 (P35) Standard AM300® 1/2 12.70 C1 (K35) Standard AM300® 1/2 12.70 C2 (K25) Standard AM300® 1/2 12.70 C5 (P35) High Rake Grade Geometry

Part No.

Insert Screw 73595-IP15-1 73595-IP15-1 73595-IP15-1 73595-IP15-1 74012-IP15-1 74012-IP15-1 74012-IP15-1 74012-IP15-1

Insert Driver

OP-060408-PW OP-060408-1PW OP-060408-2PW OP-060408-PWHR OP-080508-PW OP-080508-1PW OP-080508-2PW OP-080508-PWHR

8IP-15 8IP-15 8IP-15 8IP-15 8IP-15 8IP-15 8IP-15 8IP-15

E

THREADING

*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength

Pilot Accessories

Admissible Tightening Torque* 27.0 in-lbs (305 N-cm) 27.0 in-lbs (305 N-cm) 15.5 in-lbs (175 N-cm) 27.0 in-lbs (305 N-cm) 27.0 in-lbs (305 N-cm)

Pilot Style

Series

Insert Screws 739-IP9-1 7375-IP9-1 72567-IP8-1 7375-IP9-1 739-IP9-1

Insert Driver

T-A T-A

1

8IP-9 8IP-9 8IP-8 8IP-9 8IP-9

1**

GEN3SYS GEN3SYS GEN3SYS

17 18 22

X

*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength

Nonstocked diameters are also available. Follow the examples shown below. Inch 38 series, T-A (1 series), 1.6790" Part No. = V3801D-1.6790 Metric 38 series, T-A (1 series), 42.15 mm Part No. = V3801D-42.15

A50: 28 - 29

A50: 2 - 5

Section A20 Section A25 & A30

SPECIALS

Key on A50: 1

IC inserts sold in multiples of 2 | Insert screws sold in multiples of 10

A50: 10

www.alliedmachine.com | 1.330.343.4283

DRILLING | APX™ Drill: Deep Hole / Large Diameter Replaceable Insert Drilling System

44

APX Drill Holders 44 Series | Diameter Range: 1.732" - 2.008" (44.00 mm - 50.99 mm)

A

L 1

DRILLING

L 3

L 7

D 2

D 5

P 1

L 2

Straight Shank

B

Body

Shank

Length

D 5

L 2

L 3

L 1

L 7

D 2

P 1

Part No.

W4403H-150F W4405H-150F W4408H-150F W4410H-150F W4403H-200F W4405H-200F W4408H-200F W4410H-200F W4403H-40FM W4405H-40FM W4408H-40FM W4410H-40FM W4403H-50FM W4405H-50FM W4408H-50FM W4410H-50FM

3xD 5xD 8xD 3xD 5xD 8xD 10xD 10xD 3xD 5xD 8xD 3xD 5xD 8xD 10xD 10xD

1.732 - 2.008 1.732 - 2.008 1.732 - 2.008 1.732 - 2.008 1.732 - 2.008 1.732 - 2.008 1.732 - 2.008 1.732 - 2.008 44.00 - 50.99 44.00 - 50.99 44.00 - 50.99 44.00 - 50.99 44.00 - 50.99 44.00 - 50.99 44.00 - 50.99 44.00 - 50.99

6

8-17/32 12-35/64 18-37/64 22-19/32 8-33/64 12-35/64 18-37/64 22-19/32

11-15/64

2-11/16 2-11/16 2-11/16 2-11/16

1-1/2 1-1/2 1-1/2 1-1/2

1/4 NPT 1/4 NPT 1/4 NPT 1/4 NPT 1/4 NPT 1/4 NPT 1/4 NPT 1/4 NPT 1/4 BSPT 1/4 BSPT 1/4 BSPT 1/4 BSPT 1/4 BSPT 1/4 BSPT 1/4 BSPT 1/4 BSPT

BORING

10 16

15-1/4

21-17/64 25-9/32 13-1/32 17-3/64 23-5/64 27-3/32

20-1/8

6

4-1/2 4-1/2 4-1/2 4-1/2 70.00 70.00 70.00 70.00 80.00 80.00 80.00 80.00

2 2 2 2

10 16

20-1/8

C

152.00 255.00 408.00 510.01 152.00 255.00 409.00 510.01

216.79 318.80 471.81 573.81 216.79 318.80 471.70 573.81

286.89 388.90 541.81 643.79 296.90 398.80 551.69 653.80

40.00 40.00 40.00 40.00 50.00 50.00 50.00 50.00

REAMING

L 1

L 3

D

BURNISHING

D 5

L 2

CAT Integral Shank

D 5

Body

Length

inch

mm

L 2

L 3

L 1

Shank CV40 CV40 CV40 CV40 CV50 CV50 CV50 CV50

Part No.

W4403H-CV40 W4405H-CV40 W4408H-CV40 W4410H-CV40 W4403H-CV50 W4405H-CV50 W4408H-CV50 W4410H-CV50

3xD 5xD 8xD 3xD 5xD 8xD 10xD 10xD

1.732 - 2.008 1.732 - 2.008 1.732 - 2.008 1.732 - 2.008 1.732 - 2.008 1.732 - 2.008 1.732 - 2.008 1.732 - 2.008

44.00 - 50.99 44.00 - 50.99 44.00 - 50.99 44.00 - 50.99 44.00 - 50.99 44.00 - 50.99 44.00 - 50.99 44.00 - 50.99

6

9-1/4

11-15/16 15-61/64 21-63/64

E

10 16

13-17/64 19-19/64 23-5/16 13-17/64 19-19/64 23-5/16 9-1/4

20-1/8

26

THREADING

6

13-1/4

10 16 20

17-17/64 23-19/64 27-5/16

Connection Accessories

X

Mounting Screw

Mounting Screw Driver

Admissible Tightening Torque*

75020-IP20-1

8IP-20

60 in-lb (678 N-cm)

*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength Refer to Speed and Feed charts for recommended adjustments to speeds and feeds. Refer to page A50: 30 for deep hole drilling guidelines in this section of the catalog. Visit www.alliedmachine.com/DeepHoleGuidelines for the most up-to-date information and procedures. Factory technical assistance is available for your specific applications through our Application Engineering Team. ext: 7611 | email: appeng@alliedmachine.com WARNING

SPECIALS

Mounting screws sold in multiples of 4 = Imperial (in) = Metric (mm)

www.alliedmachine.com | 1.330.343.4283

A50: 11

51

DRILLING | APX™ Drill: Deep Hole / Large Diameter Replaceable Insert Drilling System

APX Drill Heads

A

51 Series | Diameter Range: 2.008" - 2.244" (51.00 mm - 56.99 mm)

D 5

D 5

DRILLING

D 5 D 1

D 5 D 1

B

L 9

L 9

T-A® Head

GEN3SYS® XT Pro Head

Heads

BORING

Head

T-A Head

GEN3SYS XT Pro Head

IC Insert Size

D 5 fractional

D 5 inch

D 5 metric

Pilot Series T-A Pro Insert T-A (-TC) Insert 1** TA#1-19.84 1C11H-0025-TC

Pilot Series Pilot Insert

D 1

L 9

Part No.

Part No.

inch metric

V5101D-51

V5118D-51

-

2.008 51.00 25/32 11/32

18 XT#18-19.84 1/2 12.70 18 XT#18-19.84 1/2 12.70 18 XT#18-19.84 1/2 12.70 18 XT#18-19.84 1/2 12.70 20 XT#20-21.43 1/2 12.70 20 XT#20-21.43 1/2 12.70 20 XT#20-21.43 1/2 12.70 22 XT#22-23.81 1/2 12.70 22 XT#22-23.81 1/2 12.70 22 XT#22-23.81 1/2 12.70 22 XT#22-23.81 1/2 12.70 22 XT#22-23.81 1/2 12.70 20 XT#20-20.64 9/16 14.29

2-1/32 2.031 51.59 25/32 11/32 V5101D-0201

1** TA#1-19.84 1C11H-0025-TC V5118D-0201

V5101D-52

V5118D-52

-

2.047 52.00 25/32 11/32

1** TA#1-19.84 1C11H-0025-TC

C

2-1/16 2.063 52.39 25/32 11/32 V5101D-0202

1** TA#1-19.84 1C11H-0025-TC V5118D-0202

V5101D-53

V5120D-53

-

2.087 53.00 27/32 11/32

1** TA#1-21.43 1C11H-0027-TC

2-3/32 2.094 53.18 27/32 11/32 V5101D-0203 2-1/8 2.125 53.98 27/32 11/32 V5101D-0204

1** TA#1-21.43 1C11H-0027-TC V5120D-0203 1** TA#1-21.43 1C11H-0027-TC V5120D-0204

REAMING

V5101D-54

V5122D-54

-

2.126 54.00 15/16 11/32

1 TA#1-23.81 1C11H-0030-TC

2-5/32 2.156 54.77 15/16 11/32 V5101D-0205

1 TA#1-23.81 1C11H-0030-TC V5122D-0205

V5101D-55

V5122D-55

-

2.165 55.00 15/16 11/32

1 TA#1-23.81 1C11H-0030-TC

2-3/16 2.188 55.56 15/16 11/32 V5101D-0206

1 TA#1-23.81 1C11H-0030-TC V5122D-0206

V5101D-56

V5122D-56

-

2.205 56.00 15/16 11/32

1 TA#1-23.81 1C11H-0030-TC

2-7/32 2.219 56.36 13/16 11/32 V5101D-0207

1** TA#1-20.64 1C11H-0026-TC V5120D-0207

#Denotes ISO material/geometry (P= steel, K= cast iron, N= nonferrous)

D

IC Inserts

BURNISHING

Size

Admissible Tightening Torque* 61.0 in-lbs (690 N-cm) 61.0 in-lbs (690 N-cm) 61.0 in-lbs (690 N-cm) 61.0 in-lbs (690 N-cm) 121.0 in-lbs (1370 N-cm) 121.0 in-lbs (1370 N-cm) 121.0 in-lbs (1370 N-cm) 121.0 in-lbs (1370 N-cm)

Coating inch metric AM300® 1/2 12.70 C5 (P35) Standard AM300® 1/2 12.70 C1 (K35) Standard AM300® 1/2 12.70 C2 (K25) Standard AM300® 1/2 12.70 C5 (P35) High Rake AM300® 9/16 14.29 C5 (P35) Standard AM300® 9/16 14.29 C1 (K35) Standard AM300® 9/16 14.29 C2 (K25) Standard AM300® 9/16 14.29 C5 (P35) High Rake Grade Geometry

Part No.

Insert Screw 74012-IP15-1 74012-IP15-1 74012-IP15-1 74012-IP15-1 75014-IP20-1 75014-IP20-1 75014-IP20-1 75014-IP20-1

Insert Driver

OP-080508-PW OP-080508-1PW OP-080508-2PW OP-080508-PWHR OP-090608-PW OP-090608-1PW OP-090608-2PW OP-090608-PWHR

8IP-15 8IP-15 8IP-15 8IP-15 8IP-20 8IP-20 8IP-20 8IP-20

E

*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength

THREADING

Pilot Accessories

Admissible Tightening Torque* 27.0 in-lbs (305 N-cm) 27.0 in-lbs (305 N-cm) 27.0 in-lbs (305 N-cm) 27.0 in-lbs (305 N-cm) 27.0 in-lbs (305 N-cm)

Pilot Style

Series

Insert Screws

Insert Driver

T-A T-A

1

739-IP9-1 7375-IP9-1 7375-IP9-1 7375-IP9-1 739-IP9-1

8IP-9 8IP-9 8IP-9 8IP-9 8IP-9

1**

GEN3SYS GEN3SYS GEN3SYS

18 20 22

X

*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength

Nonstocked diameters are also available. Follow the examples shown below. Inch 38 series, T-A (1 series), 1.6790" Part No. = V3801D-1.6790 Metric 38 series, T-A (1 series), 42.15 mm Part No. = V3801D-42.15

A50: 28 - 29

A50: 2 - 5

Section A20 Section A25 & A30

SPECIALS

Key on A50: 1

IC inserts sold in multiples of 2 | Insert screws sold in multiples of 10

A50: 12

www.alliedmachine.com | 1.330.343.4283

DRILLING | APX™ Drill: Deep Hole / Large Diameter Replaceable Insert Drilling System

51

APX Drill Holders 51 Series | Diameter Range: 2.008" - 2.244" (51.00 mm - 56.99 mm)

A

DRILLING

L 1

L 3

L 7

D 2

D 5

P 1

L 2

B

Straight Shank

Body

Shank

BORING

Length

D 5

L 2

L 3

L 1

L 7

D 2

P 1

Part No.

W5103H-200F W5105H-200F W5108H-200F W5110H-200F W5103H-50FM W5105H-50FM W5108H-50FM W5110H-50FM

3xD 5xD 8xD

2.008 - 2.244 2.008 - 2.244 2.008 - 2.244 2.008 - 2.244 51.00 - 56.99 51.00 - 56.99 51.00 - 56.99 51.00 - 56.99

6-3/8

8-7/8

13-3/8 17-7/8

4-1/2 4-1/2 4-1/2 4-1/2 80.00 80.00 80.00 80.00

2 2 2 2

1/4 NPT 1/4 NPT 1/4 NPT 1/4 NPT 1/4 BSPT 1/4 BSPT 1/4 BSPT 1/4 BSPT

11-1/8 17-7/8 22-3/8 161.80 284.99 455.90 570.00

13-3/8 20-3/32 24-19/32

24-19/32 29-3/32

10xD

3xD 5xD 8xD

225.50 339.60 510.49 624.61

305.51 419.61 590.50 704.60

50.00 50.00 50.00 50.00

C

10xD

REAMING

L 1

L 3

D 5

D

L 2

BURNISHING

CV50 Shank

D 5

Body

Length

inch

mm

L 2

L 3

L 1

Shank CV50 CV50 CV50 CV50

Part No.

W5103H-CV50 W5105H-CV50 W5108H-CV50 W5110H-CV50

3xD 5xD 8xD

2.008 - 2.244 2.008 - 2.244 2.008 - 2.244 2.008 - 2.244

51.00 - 56.99 51.00 - 56.99 51.00 - 56.99 51.00 - 56.99

6-3/8

9-47/64 14-7/32 20-61/64 25-7/16

13-47/64 18-7/32 24-61/64 29-7/16

11-1/4 17-7/8 22-3/8

E

10xD

THREADING

Connection Accessories

Mounting Screw

Mounting Screw Driver

Admissible Tightening Torque*

75020-IP20-1

8IP-20

60 in-lb (678 N-cm)

*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength

X

SPECIALS

Refer to Speed and Feed charts for recommended adjustments to speeds and feeds. Refer to page A50: 30 for deep hole drilling guidelines in this section of the catalog. Visit www.alliedmachine.com/DeepHoleGuidelines for the most up-to-date information and procedures. Factory technical assistance is available for your specific applications through our Application Engineering Team. ext: 7611 | email: appeng@alliedmachine.com WARNING

Mounting screws sold in multiples of 4 = Imperial (in) = Metric (mm)

www.alliedmachine.com | 1.330.343.4283

A50: 13

57

DRILLING | APX™ Drill: Deep Hole / Large Diameter Replaceable Insert Drilling System

APX Drill Heads

A

57 Series | Diameter Range: 2.244" - 2.480" (57.00 mm - 62.99 mm)

D 5

D 5

DRILLING

D 5 D 1

D 5 D 1

B

L 9

L 9

T-A® Head

GEN3SYS® XT Pro Head

Heads

BORING

Head

T-A Head

GEN3SYS XT Pro Head

IC Insert Size

D 5 fractional

D 5 inch

D 5 metric

Pilot Series T-A Pro Insert T-A (-TC) Insert 1 TA#1-23.02 1C11H-0029-TC

Pilot Series Pilot Insert

D 1

L 9

Part No.

Part No.

inch metric

V5701D-57

V5722D-57

-

2.244 57.00 29/32 25/64

22 XT#22-23.02 9/16 14.29 22 XT#22-23.02 9/16 14.29 22 XT#22-23.02 9/16 14.29 22 XT#22-23.02 9/16 14.29 22 XT#22-23.02 9/16 14.29 22 XT#22-23.81 9/16 14.29 22 XT#22-23.81 9/16 14.29 22 XT#22-23.81 9/16 14.29 22 XT#22-23.81 9/16 14.29 24 XT#24-25.40 9/16 14.29 24 XT#24-25.40 9/16 14.29 24 XT#24-25.40 9/16 14.29 26 XT#26-26.99 9/16 14.29 26 XT#26-26.99 9/16 14.29

2-1/4 2.250 57.15 29/32 25/64 V5701D-0208 2-9/32 2.281 57.94 29/32 25/64 V5701D-0209

1 TA#1-23.02 1C11H-0029-TC V5722D-0208 1 TA#1-23.02 1C11H-0029-TC V5722D-0209

C

V5701D-58

V5722D-58

-

2.284 58.00 29/32 25/64

1 TA#1-23.02 1C11H-0029-TC

2-5/16 2.313 58.74 29/32 25/64 V5701D-0210

1 TA#1-23.02 1C11H-0029-TC V5722D-0210

V5701D-59

V5722D-59

-

2.323 59.00 15/16 25/64

1 TA#1-23.81 1C11H-0030-TC

REAMING

2-11/32 2.344 59.53 15/16 25/64 V5701D-0211

1 TA#1-23.81 1C11H-0030-TC V5722D-0211

V5701D-60

V5722D-60

-

2.362 60.00 15/16 25/64

1 TA#1-23.81 1C11H-0030-TC

2-3/8 2.375 60.33 15/16 25/64 V5701D-0212

1 TA#1-23.81 1C11H-0030-TC V5722D-0212

V5702D-61

V5724D-61

-

2.402 61.00

1 25/64

2 TA#2-25.40 1C12H-0100-TC

1 25/64 V5702D-0213 1 25/64 V5702D-0214

2 TA#2-25.40 1C12H-0100-TC V5724D-0213 2 TA#2-25.40 1C12H-0100-TC V5724D-0214

2-13/32 2.406 61.12 2-7/16 2.438 61.91

V5702D-62

V5726D-62

-

2.441 62.00 1-1/16 25/64

2 TA#2-26.99 1C12H-0102-TC

2-15/32 2.469 62.71 1-1/16 25/64 V5702D-0215 #Denotes ISO material/geometry (P= steel, K= cast iron, N= nonferrous)

2 TA#2-26.99 1C12H-0102-TC V5726D-0215

D

IC Inserts BURNISHING

Size

Admissible Tightening Torque*

Coating inch metric AM300® 9/16 14.29 C5 (P35) Standard AM300® 9/16 14.29 C1 (K35) Standard AM300® 9/16 14.29 C2 (K25) Standard AM300® 9/16 14.29 C5 (P35) High Rake Grade Geometry

Part No.

Insert Screw 75014-IP20-1 75014-IP20-1 75014-IP20-1 75014-IP20-1

Insert Driver

OP-090608-PW OP-090608-1PW OP-090608-2PW OP-090608-PWHR

8IP-20 8IP-20 8IP-20 8IP-20

121.0 in-lbs (1370 N-cm) 121.0 in-lbs (1370 N-cm) 121.0 in-lbs (1370 N-cm) 121.0 in-lbs (1370 N-cm)

*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength

E

Pilot Accessories

THREADING

Admissible Tightening Torque* 27.0 in-lbs (305 N-cm) 61.0 in-lbs (690 N-cm) 27.0 in-lbs (305 N-cm) 27.0 in-lbs (305 N-cm) 61.0 in-lbs (690 N-cm)

Pilot Style

Series

Insert Screws

Insert Driver

T-A T-A

1 2

739-IP9-1

8IP-9

7495-IP15-1

8IP-15

GEN3SYS GEN3SYS GEN3SYS

22 24 26

739-IP9-1 739-IP9-1

8IP-9 8IP-9

7495-IP15-1

8IP-15

*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength

X

Nonstocked diameters are also available. Follow the examples shown below. Inch 38 series, T-A (1 series), 1.6790" Part No. = V3801D-1.6790 Metric 38 series, T-A (1 series), 42.15 mm Part No. = V3801D-42.15

A50: 28 - 29

A50: 2 - 5

Section A20 Section A25 & A30

SPECIALS

Key on A50: 1

IC inserts sold in multiples of 2 | Insert screws sold in multiples of 10

A50: 14

www.alliedmachine.com | 1.330.343.4283

DRILLING | APX™ Drill: Deep Hole / Large Diameter Replaceable Insert Drilling System

57

APX Drill Holders 57 Series | Diameter Range: 2.244" - 2.480" (57.00 mm - 62.99 mm)

A

DRILLING

L 1

L 3

L 7

D 2

D 5

P 1

L 2

B

Straight Shank

Body

Shank

BORING

Length

D 5

L 2

L 3

L 1

L 7

D 2

P 1

Part No.

W5703H-200F W5705H-200F W5708H-200F W5710H-200F W5703H-50FM W5705H-50FM W5708H-50FM W5710H-50FM

3xD 5xD 8xD

2.244 - 2.480 2.244 - 2.480 2.244 - 2.480 2.244 - 2.480 57.00 - 62.99 57.00 - 62.99 57.00 - 62.99 57.00 - 62.99

7-1/8

9-35/64 14-33/64 21-31/32 26-59/64

14-1/16 19-1/64 26-15/32 31-27/64

4-1/2 4-1/2 4-1/2 4-1/2 80.00 80.00 80.00 80.00

2 2 2 2

1/4 NPT 1/4 NPT 1/4 NPT 1/4 NPT 1/4 BSPT 1/4 BSPT 1/4 BSPT 1/4 BSPT

12-3/8 19-3/4 24-3/4 179.91 315.01 503.90 626.90

10xD

3xD 5xD 8xD

242.70 368.60 557.81 683.79

322.71 448.59 637.81 763.80

50.00 50.00 50.00 50.00

C

10xD

REAMING

L 1

L 3

D 5

D

BURNISHING

L 2

CV50 Shank

D 5

Body

Length

inch

mm

L 2

L 3

L 1

Shank CV50 CV50 CV50 CV50

Part No.

W5703H-CV50 W5705H-CV50 W5708H-CV50 W5710H-CV50

3xD 5xD 8xD

2.244 - 2.480 2.244 - 2.480 2.244 - 2.480 2.244 - 2.480

57.00 - 62.99 57.00 - 62.99 57.00 - 62.99 57.00 - 62.99

7-1/8

10-17/32 15-31/64 22-15/16 27-57/64

14-17/32 19-31/64 26-15/16 31-57/64

12-3/8 19-7/8 24-3/4

E

10xD

THREADING

Connection Accessories

Mounting Screw

Mounting Screw Driver

Admissible Tightening Torque*

75020-IP20-1

8IP-20

60 in-lb (678 N-cm)

*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength

X

SPECIALS

Refer to Speed and Feed charts for recommended adjustments to speeds and feeds. Refer to page A50: 30 for deep hole drilling guidelines in this section of the catalog. Visit www.alliedmachine.com/DeepHoleGuidelines for the most up-to-date information and procedures. Factory technical assistance is available for your specific applications through our Application Engineering Team. ext: 7611 | email: appeng@alliedmachine.com WARNING

Mounting screws sold in multiples of 4 = Imperial (in) = Metric (mm)

www.alliedmachine.com | 1.330.343.4283

A50: 15

Made with FlippingBook Online newsletter