A50-APX_EU-EN
Deep hole / large diameter drilling system
Boring
Reaming
Burnishing
Threading
APX ™ Drill DRILLING Deep Hole / Large Diameter Drilling System
Specials
S E C T I O N A50 APX™ Drill
APX ™ Drill Deep Hole / Large Diameter Drilling System Diameter Range: 33.00 mm - 101.60 mm (1.299" - 4.000")
Your safety and the safety of others is very important. This catalogue contains important safety messages. Always read and follow all safety precautions. This triangle is a safety hazard symbol. It alerts you to potential safety hazards that can cause tool failure and serious injury. When you see this symbol in the catalogue, look for a related safety message that may be near this triangle or referred to in the nearby text. There are safety signal words also used in the catalogue. Safety messages follow these words. WARNING WARNING (shown above) means that failure to follow the precautions in this message could result in tool failure and serious injury. NOTICE means that failure to follow the precautions in this message could result in damage to the tool or machine but not result in personal injury. NOTE and IMPORTANT are also used. These are important that you read and follow but are not safety-related. Visit www.alliedmachine.com for the most up-to-date information and procedures.
Don’t Let Your Machine Slow You Down The APX deep hole/large diameter drilling system delivers the strength and versatility needed for any deep hole drilling application. The breakthrough geometry is designed to increase penetration rates and tool life. By allowing for higher spindle speeds, the APX lets you take advantage of the power curve on modern CNC machines.
Improves hole quality and surface finish
Provides maximum durability and stability
Excellent chip control
Applicable Industries
Aerospace Agriculture
Automotive
Firearms
General Machining
Oil & Gas
Renewable Energy
APX ™ Drill Contents
Reference Icons The following icons will appear throughout the catalogue to help you navigate between products.
Introduction Information Drill Selection Guide / Assembly Details . . . . . . . . . . . . . . . 2 - 3 Pilot Insert Options / Details . . . . . . . . . . . . . . . . . 4 Product Nomenclature . . . . . . . . . . . . . . . . . 5
Setup / Assembly Information Detailed instructions and information regarding the corresponding part(s)
Recommended Cutting Data Speed and feed recommendations for optimum and safe drilling
Drill Series 33 Series . . . . . . . . . . . . . . . . 6 - 7 38 Series . . . . . . . . . . . . . . . . 8 - 9 44 Series . . . . . . . . . . . . . . 10 - 11 51 Series . . . . . . . . . . . . . . 12 - 13 57 Series . . . . . . . . . . . . . . 14 - 15 63 Series . . . . . . . . . . . . . . 16 - 17 70 Series . . . . . . . . . . . . . . 18 - 19 76 Series . . . . . . . . . . . . . . 20 - 21 83 Series . . . . . . . . . . . . . . 22 - 23 89 Series . . . . . . . . . . . . . . 24 - 25 95 Series . . . . . . . . . . . . . . 26 - 27
GEN3SYS® Pilot Inserts Lists the GEN3SYS XT Pro pilot ISO insert options for each APX drill series
T-A® Pilot Inserts Lists the T-A and GEN2 T-A pilot insert options for each APX Drill series
Through Coolant Option Indicates that the product is through coolant
Recommended Cutting Data
Metric (mm) . . . . . . . . . . . . . . . . . 28 Imperial (inch) . . . . . . . . . . . . . . . . . 29 Deep Hole Drilling Guidelines . . . . . . . . . . . . . . . . . 30
Diameter Range
Series
Metric (mm) 33.00 - 37.99 38.00 - 43.99 44.00 - 50.99 51.00 - 56.99 57.00 - 62.99 63.00 - 69.99 70.00 - 75.99 76.00 - 82.99 83.00 - 88.99 89.00 - 94.99 95.00 - 101.60
Imperial (inch) 1.299 - 1.496 1.496 - 1.732 1.732 - 2.008 2.008 - 2.244 2.244 - 2.480 2.480 - 2.756 2.756 - 2.992 2.992 - 3.268 3.268 - 3.504 3.504 - 3.740 3.740 - 4.000
33 38 44 51 57 63 70 76 83 89 95
A50: 1
DRILLING | APX™ Drill: Deep Hole / Large Diameter Replaceable Insert Drilling System
Drill Selection Guide
A
Series
33
38
44
51
57
DRILLING
Page
6 - 7
8 - 9
10 - 11
12 - 13
14 - 15
D 5 mm D 5 inch
33.00 - 37.99 1.2992 - 1.4688
38.00 - 43.99 1.4961 - 1.7322
44.00 - 50.99 1.7323 - 2.0075
51.00 - 56.99 2.0076 - 2.2438
57.00 - 62.99 2.2439 - 2.4799
B
P M K N S H
P M K N S H
P M K N S H
P M K N S H
P M K N S H
ISO Material
BORING
IC Insert Shape
IC Insert Size (mm) IC Insert Size (inch)
7.94
9.53 3/8"
9.53, 12.70 3/8", 1/2"
12.70, 14.29 1/2", 9/16"
14.29 9/16"
5/16"
Wear Pads
NO
NO
NO
NO
NO
Holders Drill Depth (mm) Drill Depth (inch)
C
112.6 - 378.6
130.5 - 439.9 5-1/8 - 17-1/4
151.5 - 510.0
161.8 - 570.0 6-3/8 - 22-3/8
179.9 - 626.9 7-1/8 - 24-3/4
4-7/16 - 14-29/32
6 - 20-1/8
REAMING
Pilot Insert T-A Series
0, 1
0, 1
1
1
1, 2
GEN3SYS XT Pro Series
-
15, 17, 18, 20
17, 18, 22
18, 20, 22
22, 24, 26
T-A® Style Pilot Insert Head • Utilises both T-A Pro and T-A inserts (0 - 2 series) • Multiple geometry options are available to achieve optimal results in different types of applications
GEN3SYS® XT Style Pilot Insert Head • Utilises GEN3SYS XT Pro inserts (15 - 32 series) • ISO geometry options are available to achieve optimal results in different types of applications
D
BURNISHING
Insert Application Recommendations Carbide Grade Options P35 (C5)
General purpose carbide grade suitable for most applications. Common application in steels and stainless steels.
K35 (C1)
Toughest carbide grade. Provides the best combination of edge strength and tool life. Recommended for less rigid applications. Higher wear-resistant carbide suitable for abrasive material applications. Recommended for grey, ductile, and nodular irons.
IC Insert AM300® • The design allows for excellent chip control and aggressive penetration rates • The proprietary AM300 coatings increase tool life above competitors’ premium coatings
K25 (C2)
E
Additional Geometry Option High Rake (HR)
Provides superior chip control and tool life in long-chipping carbon and alloy steels below 200 Bhn.
THREADING
Flanged Straight Shank
CAT40 / CAT50 Integral Shank
X
SPECIALS
A50: 2
www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com
DRILLING | APX™ Drill: Deep Hole / Large Diameter Replaceable Insert Drilling System
A
63
70
76
83
89
95
DRILLING
16 - 17
18 - 19
20 - 21
22 - 23
24 - 25
26 - 27
63.00 - 69.99 2.4800 - 2.7555
70.00 - 75.99 2.7556 - 2.9917
76.00 - 82.99 2.9918 - 3.2673
83.00 - 88.99 3.2674 - 3.5035
89.00 - 94.99 3.5036 - 3.7400
95.00 - 101.60 3.7401 - 4.0000
B
P M K N S H
P M K N S H
P M K N S H
P M K N S H
P M K N S H
P M K N S H
BORING
14.29 9/16"
9.53 3/8"
12.70
12.70
14.29 9/16"
14.29 9/16"
1/2"
1/2"
NO
YES
YES
YES
YES
YES
C
200.8 - 688.3 7-7/8 - 27-1/8
218.8 - 709.4 8-3/4 - 27-7/8
239.9 - 664.0 9-1/2 - 26-1/8
257.8 - 704.9 10-1/8 - 27-3/4
275.8 - 701.8 10-7/8 - 27-5/8
302.0 - 698.5 11-7/8 - 27-1/2
REAMING
2
2
2
2
2
2
26, 29, 32
29
29
32
29
32
A
B
D
ASSEMBLY
BURNISHING
Step 1: Lower the APX head assembly onto the APX holder.
Step 2: Insert the head mounting screws into points A and B. Tighten until the head is properly secured to the holder.
Step 3: Tighten with the head mounting driver using the torque setting chart below.
E
THREADING
Torque Setting Chart
Series
Screw
Driver
Torque
33 - 63
75020-IP20-1
8IP-20
678 N-cm (60 in-lb)
70 - 95
78027-IP30-1
8IP-30B
2825 N-cm (250 in-lb)
X
SPECIALS
www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com
A50: 3
DRILLING | APX™ Drill: Deep Hole / Large Diameter Replaceable Insert Drilling System
Pilot Insert Options
A
T-A® Pilot Inserts
T-A Tiny Chip (-TC) • Unique lip and point design for excellent chip control • Improved capabilities in long-chipping materials such as low-carbon steels and soft alloy steels • Enhanced performance in lower-powered machines for better chip formation at lower feed rates T-A High Impact (-HI) • Designed to enhance chip formation in materials with high elasticity/ductility and poor chip forming characteristics • SK2 corner preparation for increased tool life • Improves chip formation in structural, cast, and forged steels
DRILLING
B
T-A Pro P - Steels • Designed to provide increased penetration rates and tool life in steel applications • Superior geometry and edge provides excellent chip control • Allied’s multilayer AM300® coating increases heat resistance and improves tool life T-A Pro K - Cast Irons • Uniquely designed for cast/ductile iron applications • Geometry developed for maximum tool life, reduced exit burr, and improved hole finish • Allied’s multilayer TiAlN coating provides increased abrasion resistance and tool life T-A Pro N - Non-ferrous Materials • Designed for applications in aluminium, brass, and copper • The geometry yields excellent chip control in these softer materials • TiCN coating gives the versatility to run in a variety of materials while reducing buildup T-A Pro M - Stainless Steel • Designed for all stainless steels and heat-resistant super alloys • Geometry optimised for improved chip formation while minimizing exit burr • Allied’s new AM460 coating provides industry leading tool life in stainless and HRSA materials T-A Pro X - High-Speed Steel Materials • Improved chip geometry for excellent chip control in all materials • Long tool life and high-process security for the most challenging applications • Allied’s multilayer AM200® coating combines excellent heat resistance and high lubricity for wide application use T-A Standard • Excellent choice for general purpose use • Provides fast penetration rates that produce good hole size and finish • Combines highly efficient, stable cutting action to minimize power consumption
BORING
GEN3SYS® XT Pro Pilot Inserts
P
C
REAMING
K
P - Steels • Designed to provide increased penetration rates and tool life in steel applications • Superior geometry and edge provides excellent chip control • Allied’s multilayer AM420 coating increases heat resistance and improves tool life K - Cast Irons • Uniquely designed for cast/nodular iron applications • Geometry includes a corner radius for improved hole finish and heat dispersion • Allied’s multilayer AM440 coating provides increased abrasion resistance and tool life N - Non-ferrous Materials • Designed for applications in aluminium, brass, and copper • The geometry yields excellent chip control in these softer materials • TiN coating gives the versatility to run in a variety of materials while reducing buildup
D
N
P
BURNISHING
M
K
E
THREADING
X
N
NOTE: For a complete offering of pilot inserts, see sections A20 (GEN3SYS Drilling Systems), A25 (T-A Pro Drilling Systems) and A30 (T-A Drilling Systems) of our catalogue.
X
SPECIALS
A50: 4
www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com
DRILLING | APX™ Drill: Deep Hole / Large Diameter Replaceable Insert Drilling System
Product Nomenclature
APX Drill Heads
A
V 38
15
D - 0116
DRILLING
1
2
3
4
5
1. APX Head
2. Series
3. Pilot Series
V = Head
33 = 33 series * 38 = 38 series 44 = 44 series 51 = 51 series 57 = 57 series 63 = 63 series
70 = 70 series 76 = 76 series 83 = 83 series 89 = 89 series 95 = 95 series
T-A® Pilot Insert
GEN3SYS® XT Pro Pilot Insert
00 = 0 series 01 = 1 series 02 = 2 series
15 = 15 series 17 = 17 series 18 = 18 series 20 = 20 series 22 = 22 series
24 = 24 series 26 = 26 series 29 = 29 series 32 = 32 series
B
*T-A ® only
BORING
Ordering Non-Stocked Diameters:
4. Effective Cutting
5. Major Diameter
D = Double effective S = Single effective
68 = Metric
Non-stocked diameters are also available. Please refer to the price list for applicable process fees. Follow the ordering examples below:
1.5153 = Decimal 0116 = Inch
• Metric: 38 series, T-A (1 series), 42.15 mm = V3801D-42.15 • Inch: 38 series, T-A (1 series), 1.6790" = V3801D-1.6790
C
REAMING
APX Drill Holders
W 38
05
H - 200F
1
2
3
4
5
1. APX Holder
2. Series
3. Drill Length
4. Flute Style
5. Shank
W = Holder
33 = 33 series 38 = 38 series 44 = 44 series 51 = 51 series 57 = 57 series 63 = 63 series
70 = 70 series 76 = 76 series 83 = 83 series 89 = 89 series 95 = 95 series
03 = 3xD 05 = 5xD 08 = 8xD 10 = 10xD
H = Helical
150F = 1-1/2" flanged straight shank 200F = 2" flanged straight shank 40FM = 40 mm flanged straight shank 50FM = 50 mm flanged straight shank
D
BURNISHING
CV40 = CAT40 integral shank CV50 = CAT50 integral shank
D 5
L 1
L 3
L 7
E
D 5 D 1
D 2
D 5
THREADING
P 1
L 2
L 9
Reference Key Symbol
Reference Key Symbol Attribute
Attribute
Symbol Attribute
D 1 D 5
D 2 D 5
L 3 L 7 P 1
Pilot insert diameter Major cutting diameter
Shank diameter
Holder reference length
Drill diameter range
Shank length Rear pipe tap
L 9
Pilot insert length
L 1 L 2
Overall length
X
Drill depth
SPECIALS
www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com
A50: 5
33
DRILLING | APX™ Drill: Deep Hole / Large Diameter Replaceable Insert Drilling System
APX Drill Heads
33 Series | Diameter Range: 33.00 mm - 37.99 mm (1.299" - 1.496")
A
D 5
DRILLING
D 5 D 1
L 9
T-A® Head
B
Heads
Head
T-A Head
IC Insert Size
BORING
D 5 metric
D 5 inch
D 5 fractional
Part No.
Pilot Series
T-A Pro Insert
T-A (-TC) Insert 1C10H-16-TC 1C10H-16-TC 1C11H-18-TC 1C11H-18-TC 1C11H-18-TC 1C11H-18-TC 1C11H-18-TC 1C11H-20-TC 1C11H-20-TC 1C11H-20-TC 1C11H-20-TC
metric
inch 5/16 5/16 5/16 5/16 5/16 5/16 5/16 5/16 5/16 5/16 5/16
D 1
L 9
V3300D-33
33.00 1.299 33.34 1.313 34.00 1.339
-
16.00 16.00 18.00
6.35 6.35 6.35 6.35 6.35 6.35 6.35 6.35 6.35 6.35 6.35
0 0 1 1 1 1 1 1 1 1 1
TA#0-16.00 TA#0-16.00 TA#1-18.00 TA#1-18.00 TA#1-18.00 TA#1-18.00 TA#1-18.00 TA#1-20.00 TA#1-20.00 TA#1-20.00 TA#1-20.00
7.94 7.94 7.94 7.94 7.94 7.94 7.94 7.94 7.94 7.94 7.94
V3300D-0110
1-5/16
V3301D-34
-
V3301D-0111 V3301D-0112
34.13 1.344 1-11/32 18.00
34.93 1.375 35.00 1.378
1-3/8
18.00 18.00
V3301D-35
-
C
V3301D-0113
35.72 1.406 1-13/32 18.00
V3301D-36
36.00 1.417 36.51 1.438 37.00 1.457
-
20.00 20.00 20.00
V3301D-0114
1-7/16
REAMING
V3301D-37
-
V3301D-0115
37.31 1.469 1-15/32 20.00
#Denotes ISO material/geometry (P= steel, K= cast iron, N= non-ferrous)
IC Inserts
Size
Admissible Tightening Torque* 305 N-cm (27.0 in-lbs) 305 N-cm (27.0 in-lbs) 305 N-cm (27.0 in-lbs) 305 N-cm (27.0 in-lbs)
D
Coating metric inch AM300® 7.94 5/16 P35 (C5) AM300® 7.94 5/16 K35 (C1) AM300® 7.94 5/16 K25 (C2) AM300® 7.94 5/16 P35 (C5)
Grade Geometry
Part No.
Insert Screw
Insert Driver
OP-05T308-PW OP-05T308-1PW OP-05T308-2PW OP-05T308-PWHR
Standard Standard Standard High Rake
IS-10-1 IS-10-1 IS-10-1 IS-10-1
8IP-10 8IP-10 8IP-10 8IP-10
BURNISHING
*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength
Pilot Accessories
Admissible Tightening Torque* 175 N-cm (15.5 in-lbs) 305 N-cm (27.0 in-lbs)
Pilot Style
Series
Insert Screws 72567-IP8-1
Insert Driver
T-A T-A
0 1
8IP-8 8IP-9
E
7375-IP9-1
*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength
THREADING
X
Non-stocked diameters are also available. Follow the examples shown below. Metric 38 series, T-A (1 series), 42.15 mm Part No. = V3801D-42.15 Inch 38 series, T-A (1 series), 1.6790" Part No. = V3801D-1.6790
A50: 28 - 29
A50: 2 - 5
Section A25 & A30
SPECIALS
Key on A50: 1
IC inserts sold in multiples of 2 | Insert screws sold in multiples of 10
A50: 6
www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com
33
DRILLING | APX™ Drill: Deep Hole / Large Diameter Replaceable Insert Drilling System
APX Drill Holders 33 Series | Diameter Range: 33.00 mm - 37.99 mm (1.299" - 1.496")
A
L 1
DRILLING
L 3
L 7
D 2
D 5
P 1
L 2
Straight Shank
B
Body
Shank
Length
Part No.
D 5
L 2
L 3
L 1
L 7
D 2
P 1
BORING
W3303H-40FM W3305H-40FM W3308H-40FM W3310H-40FM W3303H-150F W3305H-150F W3308H-150F W3310H-150F
3xD 5xD 8xD
33.00 - 37.99 33.00 - 37.99 33.00 - 37.99 33.00 - 37.99 1.299 - 1.496 1.299 - 1.496 1.299 - 1.496 1.299 - 1.496
112.60 188.60 302.60 378.61
167.49 243.41 357.40 433.40 6-19/32 9-37/64 14-5/64 17-1/16
237.49 313.41 427.40 503.40 9-9/32 12-9/32 16-3/4 19-3/4
70.00 70.00 70.00 70.00
40.00 40.00 40.00 40.00 1-1/2 1-1/2 1-1/2 1-1/2
1/4 BSPT 1/4 BSPT 1/4 BSPT 1/4 BSPT 1/4 NPT 1/4 NPT 1/4 NPT 1/4 NPT
10xD
3xD 5xD 8xD
4-7/16 7-27/64 11-59/64 14-29/32
2-11/16 2-11/16 2-11/16 2-11/16
10xD
C
L 1
REAMING
L 3
D 5
L 2
D
CAT Integral Shank
Body
D 5
BURNISHING
Length
mm
inch
Shank CV40 CV40 CV40 CV40 CV50 CV50 CV50 CV50
Part No.
L 2
L 3
L 1
W3303H-CV40 W3305H-CV40 W3308H-CV40 W3310H-CV40 W3303H-CV50 W3305H-CV50 W3308H-CV50 W3310H-CV50
3xD 5xD 8xD 3xD 5xD 8xD 10xD 10xD
33.00 - 37.99 33.00 - 37.99 33.00 - 37.99 33.00 - 37.99 33.00 - 37.99 33.00 - 37.99 33.00 - 37.99 33.00 - 37.99
1.299 - 1.496 1.299 - 1.496 1.299 - 1.496 1.299 - 1.496 1.299 - 1.496 1.299 - 1.496 1.299 - 1.496 1.299 - 1.496
4-7/16 7-27/64 11-59/64 14-29/32 4-7/16 7-27/64 11-59/64 14-29/32
7-3/8
10-3/16 13-11/64 17-21/32 20-21/32 14-31/64 18-31/32 21-31/32 11-1/2
10-23/64 14-55/64 17-27/32 10-23/64 14-55/64 17-27/32 7-3/8
E
THREADING
Connection Accessories
Mounting Screw
Mounting Screw Driver
Admissible Tightening Torque*
75020-IP20-1
8IP-20
678 N-cm (60 in-lb)
*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength
X
SPECIALS
Refer to Speed and Feed charts for recommended adjustments to speeds and feeds. Refer to page A50: 30 for deep hole drilling guidelines in this section of the catalogue. Visit www.alliedmachine.com/DeepHoleGuidelines for the most up-to-date information and procedures. Factory technical assistance is available for your specific applications through our Application Engineering Team. email: engineering.eu@alliedmachine.com WARNING
Mounting screws sold in multiples of 4 = Metric (mm) = Imperial (in)
www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com
A50: 7
38
DRILLING | APX™ Drill: Deep Hole / Large Diameter Replaceable Insert Drilling System
APX Drill Heads
38 Series | Diameter Range: 38.00 mm - 43.99 mm (1.496" - 1.732")
A
D 5
D 5
DRILLING
D 5 D 1
D 5
D 1
L 9
L 9
T-A® Head
GEN3SYS® XT Pro Head
B
Heads
Head
T-A Head
GEN3SYS XT Pro Head
IC Insert Size
BORING
Pilot Series T-A Pro Insert T-A (-TC) Insert 0 TA#0-15.50 1C10H-15.5-TC 0 TA#0-15.50 1C10H-15.5-TC 0 TA#0-15.50 1C10H-15.5-TC 0 TA#0-15.50 1C10H-15.5-TC 0 TA#0-15.50 1C10H-15.5-TC 0 TA#0-17.50 1C10H-17.5-TC 0 TA#0-17.50 1C10H-17.5-TC 0 TA#0-17.50 1C10H-17.5-TC 0 TA#0-17.50 1C10H-17.5-TC 1 TA#1-19.50 1C11H-19.5-TC 1 TA#1-19.50 1C11H-19.5-TC 1 TA#1-19.50 1C11H-19.5-TC 1 TA#1-21.00 1C11H-21-TC 1 TA#1-21.00 1C11H-21-TC
D 5 metric
D 5 inch
D 5 fractional
Pilot Series Pilot Insert
Part No.
Part No.
metric inch
D 1
L 9
V3800D-38
V3815D-38
38.00 1.496
-
15.50 7.54
15 XT#15-15.50 9.53 3/8 15 XT#15-15.50 9.53 3/8 15 XT#15-15.50 9.53 3/8 15 XT#15-15.50 9.53 3/8 15 XT#15-15.50 9.53 3/8 17 XT#17-17.50 9.53 3/8 17 XT#17-17.50 9.53 3/8 17 XT#17-17.50 9.53 3/8 17 XT#17-17.50 9.53 3/8 18 XT#18-19.50 9.53 3/8 18 XT#18-19.50 9.53 3/8 18 XT#18-19.50 9.53 3/8 20 XT#20-21.00 9.53 3/8 20 XT#20-21.00 9.53 3/8
V3800D-0116 V3800D-0117
V3815D-0116 V3815D-0117
38.10 1.500 1-1/2 15.50 7.54 38.90 1.531 1-17/32 15.50 7.54
V3800D-39
V3815D-39
39.00 1.535
-
15.50 7.54
V3800D-0118
V3815D-0118
39.69 1.563 1-9/16 15.50 7.54
V3800D-40
V3817D-40
40.00 1.575
-
17.50 7.54
C
V3800D-0119
V3817D-0119
40.48 1.594 1-19/32 17.50 7.54
V3800D-41
V3817D-41
41.00 1.614
-
17.50 7.54
V3800D-0120
V3817D-0120
41.28 1.625 1-5/8 17.50 7.54
REAMING
V3801D-42
V3818D-42
42.00 1.654
-
19.50 7.54
V3801D-0121 V3801D-0122
V3818D-0121 V3818D-0122
42.07 1.656 1-21/32 19.50 7.54 42.86 1.688 1-11/16 19.50 7.54
V3801D-43
V3820D-43
43.00 1.693
-
21.00 7.54
V3801D-0123
V3820D-0123
43.66 1.719 1-23/32 21.00 7.54
#Denotes ISO material/geometry (P= steel, K= cast iron, N= non-ferrous)
IC Inserts
D
Size
Admissible Tightening Torque* 465 N-cm (41.0 in-lbs) 465 N-cm (41.0 in-lbs) 465 N-cm (41.0 in-lbs) 465 N-cm (41.0 in-lbs)
BURNISHING Coating
metric
inch
Grade Geometry
Part No.
Insert Screw 73595-IP15-1 73595-IP15-1 73595-IP15-1 73595-IP15-1
Insert Driver
OP-060408-PW OP-060408-1PW OP-060408-2PW OP-060408-PWHR
AM300® 9.53 AM300® 9.53 AM300® 9.53 AM300® 9.53
3/8 P35 (C5) 3/8 K35 (C1) 3/8 K25 (C2) 3/8 P35 (C5)
Standard Standard Standard High Rake
8IP-15 8IP-15 8IP-15 8IP-15
*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength
Pilot Accessories
E
Admissible Tightening Torque* 175 N-cm (15.5 in-lbs) 305 N-cm (27.0 in-lbs) 84 N-cm (7.4 in-lbs) 175 N-cm (15.5 in-lbs) 305 N-cm (27.0 in-lbs) 305 N-cm (27.0 in-lbs)
Pilot Style
Series
Insert Screws 72567-IP8-1 7375-IP9-1 7247-IP7-1 72567-IP8-1 7375-IP9-1 7375-IP9-1
Insert Driver
T-A T-A
0 1
8IP-8 8IP-9 8IP-7 8IP-8 8IP-9 8IP-9
THREADING
GEN3SYS GEN3SYS GEN3SYS GEN3SYS
15 17 18 20
*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength
X
Non-stocked diameters are also available. Follow the examples shown below. Metric 38 series, T-A (1 series), 42.15 mm Part No. = V3801D-42.15 Inch 38 series, T-A (1 series), 1.6790" Part No. = V3801D-1.6790
A50: 28 - 29
A50: 2 - 5
Section A20 Section A25 & A30
SPECIALS
Key on A50: 1
IC inserts sold in multiples of 2 | Insert screws sold in multiples of 10
A50: 8
www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com
38
DRILLING | APX™ Drill: Deep Hole / Large Diameter Replaceable Insert Drilling System
APX Drill Holders 38 Series | Diameter Range: 38.00 mm - 43.99 mm (1.496" - 1.732")
A
L 1
L 3
L 7
DRILLING
D 2
D 5
P 1
L 2
Straight Shank
Body
Shank
Length
Part No.
D 5
L 2
L 3
L 1
L 7
D 2
P 1
B
W3803H-40FM W3805H-40FM W3808H-40FM W3810H-40FM W3803H-50FM W3805H-50FM W3808H-50FM W3810H-50FM W3803H-150F W3805H-150F W3808H-150F W3810H-150F W3803H-200F W3805H-200F W3808H-200F W3810H-200F
3xD 5xD 8xD 3xD 5xD 8xD 10xD 10xD 3xD 5xD 8xD 3xD 5xD 8xD 10xD 10xD
38.00 - 43.99 38.00 - 43.99 38.00 - 43.99 38.00 - 43.99 38.00 - 43.99 38.00 - 43.99 38.00 - 43.99 38.00 - 43.99 1.496 - 1.732 1.496 - 1.732 1.496 - 1.732 1.496 - 1.732 1.496 - 1.732 1.496 - 1.732 1.496 - 1.732 1.496 - 1.732
130.51 219.99 351.99 439.90 130.51 219.99 351.99 439.90
196.49 284.51 416.51 503.91 196.49 284.51 416.51 503.90
265.71 353.70 485.70 573.71 276.50 364.49 496.99 583.91
70.00 70.00 70.00 70.00 80.00 80.00 80.00 80.00
40.00 40.00 40.00 40.00 50.00 50.00 50.00 50.00 1-1/2 1-1/2 1-1/2 1-1/2
1/4 BSPT 1/4 BSPT 1/4 BSPT 1/4 BSPT 1/4 BSPT 1/4 BSPT 1/4 BSPT 1/4 BSPT 1/4 NPT 1/4 NPT 1/4 NPT 1/4 NPT 1/4 NPT 1/4 NPT 1/4 NPT 1/4 NPT
BORING
5-1/8 8-5/8
7-47/64 11-13/64 16-25/64 19-27/32 7-47/64 11-13/64 16-25/64 19-27/32
10-25/64 13-55/64 19-3/64 22-33/64 12-15/64 15-45/64 20-57/64 24-59/64
2-11/16 2-11/16 2-11/16 2-11/16
13-7/8 17-1/4
C
5-1/8 8-5/8
4-1/2 4-1/2 4-1/2 4-1/2
2 2 2 2
REAMING
13-7/8 17-1/4
L 1
L 3
D 5
D
L 2
BURNISHING
CAT Integral Shank
Body
D 5
Length
mm
inch
Shank CV40 CV40 CV40 CV40 CV50 CV50 CV50 CV50
Part No.
L 2
L 3
L 1
W3803H-CV40 W3805H-CV40 W3808H-CV40 W3810H-CV40 W3803H-CV50 W3805H-CV50 W3808H-CV50 W3810H-CV50
3xD 5xD 8xD 3xD 5xD 8xD 10xD 10xD
38.00 - 43.99 38.00 - 43.99 38.00 - 43.99 38.00 - 43.99 38.00 - 43.99 38.00 - 43.99 38.00 - 43.99 38.00 - 43.99
1.496 - 1.732 1.496 - 1.732 1.496 - 1.732 1.496 - 1.732 1.496 - 1.732 1.496 - 1.732 1.496 - 1.732 1.496 - 1.732
5-1/8 8-5/8
8-5/16
11
11-49/64 16-31/32 20-7/16 11-49/64 16-31/32 20-7/16 8-5/16
14-29/64 19-21/32 23-1/8 12-5/16 15-49/64 20-31/32 24-7/16
13-7/8 17-1/4
5-1/8 8-5/8
E
13-7/8 17-1/4
THREADING
Connection Accessories
Mounting Screw
Mounting Screw Driver
Admissible Tightening Torque*
75020-IP20-1
8IP-20
678 N-cm (60 in-lb)
*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength
X
SPECIALS
Refer to Speed and Feed charts for recommended adjustments to speeds and feeds. Refer to page A50: 30 for deep hole drilling guidelines in this section of the catalogue. Visit www.alliedmachine.com/DeepHoleGuidelines for the most up-to-date information and procedures. Factory technical assistance is available for your specific applications through our Application Engineering Team. email: engineering.eu@alliedmachine.com WARNING
Mounting screws sold in multiples of 4 = Metric (mm) = Imperial (in)
www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com
A50: 9
44
DRILLING | APX™ Drill: Deep Hole / Large Diameter Replaceable Insert Drilling System
APX Drill Heads
44 Series | Diameter Range: 44.00 mm - 50.99 mm (1.732" - 2.008")
A
D 5
D 5
DRILLING
D 5 D 1
D 5
D 1
L 9
L 9
T-A® Head
GEN3SYS® XT Pro Head
B
Heads
Head
T-A Head
GEN3SYS XT Pro Head
IC Insert Size
BORING
Pilot Series T-A Pro Insert T-A (-TC) Insert 1 TA#1-23.00 1C11H-23-TC 1 TA#1-23.00 1C11H-23-TC 1 TA#1-23.00 1C11H-23-TC 1 TA#1-23.00 1C11H-23-TC 1 TA#1-24.00 1C11H-24-TC 1 TA#1-24.00 1C11H-24-TC 1 TA#1-24.00 1C11H-24-TC 1 TA#1-24.00 1C11H-24-TC 1 TA#1-24.00 1C11H-24-TC 1 TA#1-18.00 1C11H-18-TC 1 TA#1-18.00 1C11H-18-TC 1 TA#1-18.00 1C11H-18-TC 1 TA#1-18.00 1C11H-18-TC 1 TA#1-19.00 1C11H-19-TC 1 TA#1-19.00 1C11H-19-TC 1 TA#1-19.00 1C11H-19-TC
D 5 metric
D 5 inch
D 5 fractional
Pilot Series Pilot Insert
Part No.
Part No.
metric inch
D 1
L 9
V4401D-44
V4422D-44
44.00 1.732
-
23.00 8.33
22 XT#22-23.00 9.53 3/8 22 XT#22-23.00 9.53 3/8 22 XT#22-23.00 9.53 3/8 22 XT#22-23.00 9.53 3/8 22 XT#22-23.80 9.53 3/8 22 XT#22-23.80 9.53 3/8 22 XT#22-23.80 9.53 3/8 22 XT#22-23.80 9.53 3/8 22 XT#22-23.80 9.53 3/8 17 XT#17-17.90 12.70 1/2 17 XT#17-17.90 12.70 1/2 17 XT#17-17.90 12.70 1/2 17 XT#17-17.90 12.70 1/2 18 XT#18-19.00 12.70 1/2 18 XT#18-19.00 12.70 1/2 18 XT#18-19.00 12.70 1/2
V4401D-0124
V4422D-0124
44.45 1.750 1-3/4 23.00 8.33
V4401D-45
V4422D-45
45.00 1.772
-
23.00 8.33
V4401D-0125
V4422D-0125
45.25 1.781 1-25/32 23.00 8.33
V4401D-46
V4422D-46
46.00 1.811
-
24.00 8.33
V4401D-0126 V4401D-0127
V4422D-0126 V4422D-0127
46.04 1.813 1-13/16 24.00 8.33 46.83 1.844 1-27/32 24.00 8.33
C
V4401D-47
V4422D-47
47.00 1.850
-
24.00 8.33
V4401D-0128
V4422D-0128
47.63 1.875 1-7/8 24.00 8.33
V4401D-48
V4417D-48
48.00 1.890
-
18.00 8.33
REAMING
V4401D-0129 V4401D-49 V4401D-0130 V4401D-50 V4401D-0131 V4401D-0200
V4417D-0129 V4417D-49 V4417D-0130 V4418D-50 V4418D-0131 V4418D-0200
48.42 1.906 1-29/32 18.00 8.33
49.00 1.929
-
18.00 8.33
49.21 1.938 1-15/16 18.00 8.33
50.00 1.969
-
19.00 8.33
50.01 1.969 1-31/32 19.00 8.33
50.80 2.000
2
19.00 8.33
#Denotes ISO material/geometry (P= steel, K= cast iron, N= non-ferrous)
IC Inserts
D
Size
Admissible Tightening Torque* 465 N-cm (41.0 in-lbs) 465 N-cm (41.0 in-lbs) 465 N-cm (41.0 in-lbs) 465 N-cm (41.0 in-lbs) 690 N-cm (61.0 in-lbs) 690 N-cm (61.0 in-lbs) 690 N-cm (61.0 in-lbs) 690 N-cm (61.0 in-lbs)
BURNISHING Coating
Grade Geometry metric inch AM300® 9.53 3/8 P35 (C5) Standard AM300® 9.53 3/8 K35 (C1) Standard AM300® 9.53 3/8 K25 (C2) Standard AM300® 9.53 3/8 P35 (C5) High Rake AM300® 12.70 1/2 P35 (C5) Standard AM300® 12.70 1/2 K35 (C1) Standard AM300® 12.70 1/2 K25 (C2) Standard AM300® 12.70 1/2 P35 (C5) High Rake
Part No.
Insert Screw 73595-IP15-1 73595-IP15-1 73595-IP15-1 73595-IP15-1 74012-IP15-1 74012-IP15-1 74012-IP15-1 74012-IP15-1
Insert Driver
OP-060408-PW OP-060408-1PW OP-060408-2PW OP-060408-PWHR OP-080508-PW OP-080508-1PW OP-080508-2PW OP-080508-PWHR
8IP-15 8IP-15 8IP-15 8IP-15 8IP-15 8IP-15 8IP-15 8IP-15
*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength
E
Pilot Accessories
THREADING
Admissible Tightening Torque* 305 N-cm (27.0 in-lbs) 175 N-cm (15.5 in-lbs) 305 N-cm (27.0 in-lbs) 305 N-cm (27.0 in-lbs)
Pilot Style
Series
Insert Screws 7375-IP9-1 72567-IP8-1 7375-IP9-1
Insert Driver
T-A
1
8IP-9 8IP-8 8IP-9 8IP-9
GEN3SYS GEN3SYS GEN3SYS
17 18 22
739-IP9-1
*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength
X
Non-stocked diameters are also available. Follow the examples shown below. Metric 38 series, T-A (1 series), 42.15 mm Part No. = V3801D-42.15 Inch 38 series, T-A (1 series), 1.6790" Part No. = V3801D-1.6790
A50: 28 - 29
A50: 2 - 5
Section A20 Section A25 & A30
SPECIALS
Key on A50: 1
IC inserts sold in multiples of 2 | Insert screws sold in multiples of 10
A50: 10
www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com
44
DRILLING | APX™ Drill: Deep Hole / Large Diameter Replaceable Insert Drilling System
APX Drill Holders 44 Series | Diameter Range: 44.00 mm - 50.99 mm (1.732" - 2.008")
A
L 1
L 3
L 7
DRILLING
D 2
D 5
P 1
L 2
Straight Shank
Body
Shank
Length
Part No.
D 5
L 2
L 3
L 1
L 7
D 2
P 1
B
W4403H-40FM W4405H-40FM W4408H-40FM W4410H-40FM W4403H-50FM W4405H-50FM W4408H-50FM W4410H-50FM W4403H-150F W4405H-150F W4408H-150F W4410H-150F W4403H-200F W4405H-200F W4408H-200F W4410H-200F
3xD 5xD 8xD 3xD 5xD 8xD 10xD 10xD 3xD 5xD 8xD 3xD 5xD 8xD 10xD 10xD
44.00 - 50.99 44.00 - 50.99 44.00 - 50.99 44.00 - 50.99 44.00 - 50.99 44.00 - 50.99 44.00 - 50.99 44.00 - 50.99 1.732 - 2.008 1.732 - 2.008 1.732 - 2.008 1.732 - 2.008 1.732 - 2.008 1.732 - 2.008 1.732 - 2.008 1.732 - 2.008
152.00 255.00 408.00 510.01 152.00 255.00 409.00 510.01
216.79 318.80 471.81 573.81 216.79 318.80 471.70 573.81
286.89 388.90 541.81 643.79 296.90 398.80 551.69 653.80
70.00 70.00 70.00 70.00 80.00 80.00 80.00 80.00
40.00 40.00 40.00 40.00 50.00 50.00 50.00 50.00 1-1/2 1-1/2 1-1/2 1-1/2
1/4 BSPT 1/4 BSPT 1/4 BSPT 1/4 BSPT 1/4 BSPT 1/4 BSPT 1/4 BSPT 1/4 BSPT 1/4 NPT 1/4 NPT 1/4 NPT 1/4 NPT 1/4 NPT 1/4 NPT 1/4 NPT 1/4 NPT
BORING
6
8-17/32 12-35/64 18-37/64 22-19/32 8-33/64 12-35/64 18-37/64 22-19/32
11-15/64
2-11/16 2-11/16 2-11/16 2-11/16
10 16
15-1/4
21-17/64 25-9/32 13-1/32 17-3/64 23-5/64 27-3/32
20-1/8
C
6
4-1/2 4-1/2 4-1/2 4-1/2
2 2 2 2
10 16
REAMING
20-1/8
L 1
L 3
D 5
D
L 2
BURNISHING
CAT Integral Shank
Body
D 5
Length
mm
inch
Shank CV40 CV40 CV40 CV40 CV50 CV50 CV50 CV50
Part No.
L 2
L 3
L 1
W4403H-CV40 W4405H-CV40 W4408H-CV40 W4410H-CV40 W4403H-CV50 W4405H-CV50 W4408H-CV50 W4410H-CV50
3xD 5xD 8xD 3xD 5xD 8xD 10xD 10xD
44.00 - 50.99 44.00 - 50.99 44.00 - 50.99 44.00 - 50.99 44.00 - 50.99 44.00 - 50.99 44.00 - 50.99 44.00 - 50.99
1.732 - 2.008 1.732 - 2.008 1.732 - 2.008 1.732 - 2.008 1.732 - 2.008 1.732 - 2.008 1.732 - 2.008 1.732 - 2.008
6
9-1/4
11-15/16 15-61/64 21-63/64
10 16
13-17/64 19-19/64 23-5/16 13-17/64 19-19/64 23-5/16 9-1/4
20-1/8
26
6
13-1/4
10 16 20
17-17/64 23-19/64 27-5/16
E
THREADING
Connection Accessories
Mounting Screw
Mounting Screw Driver
Admissible Tightening Torque*
75020-IP20-1
8IP-20
678 N-cm (60 in-lb)
*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength
X
SPECIALS
Refer to Speed and Feed charts for recommended adjustments to speeds and feeds. Refer to page A50: 30 for deep hole drilling guidelines in this section of the catalogue. Visit www.alliedmachine.com/DeepHoleGuidelines for the most up-to-date information and procedures. Factory technical assistance is available for your specific applications through our Application Engineering Team. email: engineering.eu@alliedmachine.com WARNING
Mounting screws sold in multiples of 4 = Metric (mm) = Imperial (in)
www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com
A50: 11
51
DRILLING | APX™ Drill: Deep Hole / Large Diameter Replaceable Insert Drilling System
APX Drill Heads
51 Series | Diameter Range: 51.00 mm - 56.99 mm (2.008" - 2.244")
A
D 5
D 5
DRILLING
D 5 D 1
D 5 D 1
L 9
L 9
T-A® Head
GEN3SYS® XT Pro Head
B
Heads
Head
T-A Head
GEN3SYS XT Pro Head
IC Insert Size
BORING
Pilot Series T-A Pro Insert T-A (-TC) Insert 1 TA#1-20.00 1C11H-20-TC 1 TA#1-20.00 1C11H-20-TC 1 TA#1-20.00 1C11H-20-TC 1 TA#1-20.00 1C11H-20-TC 1 TA#1-21.50 1C11H-21.5-TC 1 TA#1-21.50 1C11H-21.5-TC 1 TA#1-21.50 1C11H-21.5-TC 1 TA#1-24.00 1C11H-24-TC 1 TA#1-24.00 1C11H-24-TC 1 TA#1-24.00 1C11H-24-TC 1 TA#1-24.00 1C11H-24-TC 1 TA#1-24.00 1C11H-24-TC 1 TA#1-21.00 1C11H-21-TC
D 5 metric
D 5 inch
D 5 fractional
Pilot Series Pilot Insert
Part No.
Part No.
metric inch
D 1
L 9
V5101D-51
V5118D-51
51.00 2.008
-
20.00 8.73
18 XT#18-19.80 12.70 1/2 18 XT#18-19.80 12.70 1/2 18 XT#18-19.80 12.70 1/2 18 XT#18-19.80 12.70 1/2 20 XT#20-21.50 12.70 1/2 20 XT#20-21.50 12.70 1/2 20 XT#20-21.50 12.70 1/2 22 XT#22-23.80 12.70 1/2 22 XT#22-23.80 12.70 1/2 22 XT#22-23.80 12.70 1/2 22 XT#22-23.80 12.70 1/2 22 XT#22-23.80 12.70 1/2 20 XT#20-21.00 14.29 9/16
V5101D-0201
V5118D-0201
51.59 2.031 2-1/32 20.00 8.73
V5101D-52
V5118D-52
52.00 2.047
-
20.00 8.73
V5101D-0202
V5118D-0202
52.39 2.063 2-1/16 20.00 8.73
V5101D-53
V5120D-53
53.00 2.087
-
21.50 8.73
V5101D-0203 V5101D-0204
V5120D-0203 V5120D-0204
53.18 2.094 2-3/32 21.50 8.73 53.98 2.125 2-1/8 21.50 8.73
C
V5101D-54
V5122D-54
54.00 2.126
-
24.00 8.73
V5101D-0205
V5122D-0205
54.77 2.156 2-5/32 24.00 8.73
REAMING
V5101D-55
V5122D-55
55.00 2.165
-
24.00 8.73
V5101D-0206
V5122D-0206
55.56 2.188 2-3/16 24.00 8.73
V5101D-56
V5122D-56
56.00 2.205
-
24.00 8.73
V5101D-0207
V5120D-0207
56.36 2.219 2-7/32 21.00 8.73
#Denotes ISO material/geometry (P= steel, K= cast iron, N= non-ferrous)
IC Inserts
Size
D
Admissible Tightening Torque* 690 N-cm (61.0 in-lbs) 690 N-cm (61.0 in-lbs) 690 N-cm (61.0 in-lbs) 690 N-cm (61.0 in-lbs) 1370 N-cm (121.0 in-lbs) 1370 N-cm (121.0 in-lbs) 1370 N-cm (121.0 in-lbs) 1370 N-cm (121.0 in-lbs)
Coating metric inch AM300® 12.70 1/2 P35 (C5) Standard AM300® 12.70 1/2 K35 (C1) Standard AM300® 12.70 1/2 K25 (C2) Standard AM300® 12.70 1/2 P35 (C5) High Rake AM300® 14.29 9/16 P35 (C5) Standard AM300® 14.29 9/16 K35 (C1) Standard AM300® 14.29 9/16 K25 (C2) Standard AM300® 14.29 9/16 P35 (C5) High Rake Grade Geometry
Part No.
Insert Screw 74012-IP15-1 74012-IP15-1 74012-IP15-1 74012-IP15-1 75014-IP20-1 75014-IP20-1 75014-IP20-1 75014-IP20-1
Insert Driver
BURNISHING
OP-080508-PW OP-080508-1PW OP-080508-2PW OP-080508-PWHR OP-090608-PW OP-090608-1PW OP-090608-2PW OP-090608-PWHR
8IP-15 8IP-15 8IP-15 8IP-15 8IP-20 8IP-20 8IP-20 8IP-20
*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength
E
Pilot Accessories
Admissible Tightening Torque* 305 N-cm (27.0 in-lbs) 305 N-cm (27.0 in-lbs) 305 N-cm (27.0 in-lbs) 305 N-cm (27.0 in-lbs)
THREADING
Pilot Style
Series
Insert Screws
Insert Driver
T-A
1
7375-IP9-1 7375-IP9-1 7375-IP9-1 739-IP9-1
8IP-9 8IP-9 8IP-9 8IP-9
GEN3SYS GEN3SYS GEN3SYS
18 20 22
*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength
X
Non-stocked diameters are also available. Follow the examples shown below. Metric 38 series, T-A (1 series), 42.15 mm Part No. = V3801D-42.15 Inch 38 series, T-A (1 series), 1.6790" Part No. = V3801D-1.6790
A50: 28 - 29
A50: 2 - 5
Section A20 Section A25 & A30
SPECIALS
Key on A50: 1
IC inserts sold in multiples of 2 | Insert screws sold in multiples of 10
A50: 12
www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com
51
DRILLING | APX™ Drill: Deep Hole / Large Diameter Replaceable Insert Drilling System
APX Drill Holders 51 Series | Diameter Range: 51.00 mm - 56.99 mm (2.008" - 2.244")
A
L 1
DRILLING
L 3
L 7
D 2
D 5
P 1
L 2
Straight Shank
B
Body
Shank
Length
Part No.
D 5
L 2
L 3
L 1
L 7
D 2
P 1
BORING
W5103H-50FM W5105H-50FM W5108H-50FM W5110H-50FM W5103H-200F W5105H-200F W5108H-200F W5110H-200F
3xD 5xD 8xD
51.00 - 56.99 51.00 - 56.99 51.00 - 56.99 51.00 - 56.99 2.008 - 2.244 2.008 - 2.244 2.008 - 2.244 2.008 - 2.244
161.80 284.99 455.90 570.00
225.50 339.60 510.49 624.61
305.51 419.61 590.50 704.60 13-3/8 17-7/8
80.00 80.00 80.00 80.00 4-1/2 4-1/2 4-1/2 4-1/2
50.00 50.00 50.00 50.00
1/4 BSPT 1/4 BSPT 1/4 BSPT 1/4 BSPT 1/4 NPT 1/4 NPT 1/4 NPT 1/4 NPT
10xD
3xD 5xD 8xD
6-3/8
8-7/8
2 2 2 2
11-1/8 17-7/8 22-3/8
13-3/8 20-3/32 24-19/32
24-19/32 29-3/32
10xD
C
REAMING
L 1
L 3
D 5
L 2
D
CV50 Shank
BURNISHING
Body
D 5
Length
mm
inch
Shank CV50 CV50 CV50 CV50
Part No.
L 2
L 3
L 1
W5103H-CV50 W5105H-CV50 W5108H-CV50 W5110H-CV50
3xD 5xD 8xD
51.00 - 56.99 51.00 - 56.99 51.00 - 56.99 51.00 - 56.99
2.008 - 2.244 2.008 - 2.244 2.008 - 2.244 2.008 - 2.244
6-3/8
9-47/64 14-7/32 20-61/64 25-7/16
13-47/64 18-7/32 24-61/64 29-7/16
11-1/4 17-7/8 22-3/8
10xD
E
Connection Accessories
THREADING
Mounting Screw
Mounting Screw Driver
Admissible Tightening Torque*
75020-IP20-1
8IP-20
678 N-cm (60 in-lb)
*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength
X
SPECIALS
Refer to Speed and Feed charts for recommended adjustments to speeds and feeds. Refer to page A50: 30 for deep hole drilling guidelines in this section of the catalogue. Visit www.alliedmachine.com/DeepHoleGuidelines for the most up-to-date information and procedures. Factory technical assistance is available for your specific applications through our Application Engineering Team. email: engineering.eu@alliedmachine.com WARNING
Mounting screws sold in multiples of 4 = Metric (mm) = Imperial (in)
www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com
A50: 13
57
DRILLING | APX™ Drill: Deep Hole / Large Diameter Replaceable Insert Drilling System
APX Drill Heads
57 Series | Diameter Range: 57.00 mm - 62.99 mm (2.244" - 2.480")
A
D 5
D 5
DRILLING
D 5 D 1
D 5 D 1
L 9
L 9
T-A® Head
GEN3SYS® XT Pro Head
B
Heads
Head
T-A Head
GEN3SYS XT Pro Head
IC Insert Size
BORING
Pilot Series T-A Pro Insert T-A (-TC) Insert 1 TA#1-23.00 1C11H-23-TC 1 TA#1-23.00 1C11H-23-TC 1 TA#1-23.00 1C11H-23-TC 1 TA#1-23.00 1C11H-23-TC 1 TA#1-23.00 1C11H-23-TC 1 TA#1-24.00 1C11H-24-TC 1 TA#1-24.00 1C11H-24-TC 1 TA#1-24.00 1C11H-24-TC 1 TA#1-24.00 1C11H-24-TC 2 TA#2-25.50 1C12H-25.5-TC 2 TA#2-25.50 1C12H-25.5-TC 2 TA#2-25.50 1C12H-25.5-TC 2 TA#2-27.00 1C12H-27-TC 2 TA#2-27.00 1C12H-27-TC
D 5 metric
D 5 inch
D 5 fractional
Pilot Series Pilot Insert
Part No.
Part No.
metric inch
D 1
L 9
V5701D-57
V5722D-57
57.00 2.244
-
23.00 9.92
22 XT#22-23.00 14.29 9/16 22 XT#22-23.00 14.29 9/16 22 XT#22-23.00 14.29 9/16 22 XT#22-23.00 14.29 9/16 22 XT#22-23.00 14.29 9/16 22 XT#22-23.80 14.29 9/16 22 XT#22-23.80 14.29 9/16 22 XT#22-23.80 14.29 9/16 22 XT#22-23.80 14.29 9/16 24 XT#24-25.50 14.29 9/16 24 XT#24-25.50 14.29 9/16 24 XT#24-25.50 14.29 9/16 26 XT#26-27.00 14.29 9/16 26 XT#26-27.00 14.29 9/16
V5701D-0208 V5701D-0209
V5722D-0208 V5722D-0209
57.15 2.250 2-1/4 23.00 9.92 57.94 2.281 2-9/32 23.00 9.92
V5701D-58
V5722D-58
58.00 2.284
-
23.00 9.92
V5701D-0210
V5722D-0210
58.74 2.313 2-5/16 23.00 9.92
V5701D-59
V5722D-59
59.00 2.323
-
24.00 9.92
C
V5701D-0211
V5722D-0211
59.53 2.344 2-11/32 24.00 9.92
V5701D-60
V5722D-60
60.00 2.362
-
24.00 9.92
V5701D-0212
V5722D-0212
60.33 2.375 2-3/8 24.00 9.92
REAMING
V5702D-61
V5724D-61
61.00 2.402
-
25.50 9.92
V5702D-0213 V5702D-0214
V5724D-0213 V5724D-0214
61.12 2.406 2-13/32 25.50 9.92 61.91 2.438 2-7/16 25.50 9.92
V5702D-62
V5726D-62
62.00 2.441
-
27.00 9.92
V5702D-0215
V5726D-0215
62.71 2.469 2-15/32 27.00 9.92
#Denotes ISO material/geometry (P= steel, K= cast iron, N= non-ferrous)
IC Inserts
D
Size
Admissible Tightening Torque*
BURNISHING Coating
Grade Geometry metric inch AM300® 14.29 9/16 P35 (C5) Standard AM300® 14.29 9/16 K35 (C1) Standard AM300® 14.29 9/16 K25 (C2) Standard AM300® 14.29 9/16 P35 (C5) High Rake
Part No.
Insert Screw 75014-IP20-1 75014-IP20-1 75014-IP20-1 75014-IP20-1
Insert Driver
OP-090608-PW OP-090608-1PW OP-090608-2PW OP-090608-PWHR
8IP-20 8IP-20 8IP-20 8IP-20
1370 N-cm (121.0 in-lbs) 1370 N-cm (121.0 in-lbs) 1370 N-cm (121.0 in-lbs) 1370 N-cm (121.0 in-lbs)
*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength
Pilot Accessories
E
Admissible Tightening Torque* 305 N-cm (27.0 in-lbs) 690 N-cm (61.0 in-lbs) 305 N-cm (27.0 in-lbs) 305 N-cm (27.0 in-lbs) 690 N-cm (61.0 in-lbs)
Pilot Style
Series
Insert Screws 7375-IP9-1 7495-IP15-1
Insert Driver
T-A T-A
1 2
8IP-9
THREADING
8IP-15
GEN3SYS GEN3SYS GEN3SYS
22 24 26
739-IP9-1 739-IP9-1
8IP-9 8IP-9
7495-IP15-1
8IP-15
*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength
X
Non-stocked diameters are also available. Follow the examples shown below. Metric 38 series, T-A (1 series), 42.15 mm Part No. = V3801D-42.15 Inch 38 series, T-A (1 series), 1.6790" Part No. = V3801D-1.6790
A50: 28 - 29
A50: 2 - 5
Section A20 Section A25 & A30
SPECIALS
Key on A50: 1
IC inserts sold in multiples of 2 | Insert screws sold in multiples of 10
A50: 14
www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com
Made with FlippingBook - Online Brochure Maker