A50-APX_EU-EN

33

DRILLING | APX™ Drill: Deep Hole / Large Diameter Replaceable Insert Drilling System

APX Drill Holders 33 Series | Diameter Range: 33.00 mm - 37.99 mm (1.299" - 1.496")

A

L 1

DRILLING

L 3

L 7

D 2

D 5

P 1

L 2

Straight Shank

B

Body

Shank

D 5

L 2

L 3

L 1

L 7

D 2

P 1

Length

Part No.

BORING

W3303H-40FM W3305H-40FM W3308H-40FM W3310H-40FM W3303H-150F W3305H-150F W3308H-150F W3310H-150F

3xD 5xD 8xD

33.00 - 37.99 33.00 - 37.99 33.00 - 37.99 33.00 - 37.99 1.299 - 1.496 1.299 - 1.496 1.299 - 1.496 1.299 - 1.496

112.60 188.60 302.60 378.61

167.49 243.41 357.40 433.40 6-19/32 9-37/64 14-5/64 17-1/16

237.49 313.41 427.40 503.40 9-9/32 12-9/32 16-3/4 19-3/4

70.00 70.00 70.00 70.00

40.00 40.00 40.00 40.00 1-1/2 1-1/2 1-1/2 1-1/2

1/4 BSPT 1/4 BSPT 1/4 BSPT 1/4 BSPT 1/4 NPT 1/4 NPT 1/4 NPT 1/4 NPT

10xD

3xD 5xD 8xD

4-7/16 7-27/64 11-59/64 14-29/32

2-11/16 2-11/16 2-11/16 2-11/16

10xD

C

L 1

REAMING

L 3

D 5

L 2

D

CAT Integral Shank

D 5

Body

BURNISHING

L 2

L 3

L 1

Length

mm

inch

Shank CV40 CV40 CV40 CV40 CV50 CV50 CV50 CV50

Part No.

W3303H-CV40 W3305H-CV40 W3308H-CV40 W3310H-CV40 W3303H-CV50 W3305H-CV50 W3308H-CV50 W3310H-CV50

3xD 5xD 8xD 3xD 5xD 8xD 10xD 10xD

33.00 - 37.99 33.00 - 37.99 33.00 - 37.99 33.00 - 37.99 33.00 - 37.99 33.00 - 37.99 33.00 - 37.99 33.00 - 37.99

1.299 - 1.496 1.299 - 1.496 1.299 - 1.496 1.299 - 1.496 1.299 - 1.496 1.299 - 1.496 1.299 - 1.496 1.299 - 1.496

4-7/16 7-27/64 11-59/64 14-29/32 4-7/16 7-27/64 11-59/64 14-29/32

7-3/8

10-3/16 13-11/64 17-21/32 20-21/32 14-31/64 18-31/32 21-31/32 11-1/2

10-23/64 14-55/64 17-27/32 10-23/64 14-55/64 17-27/32 7-3/8

E

THREADING

ConnecƟon Accessories

MounƟng Screw

MounƟng Screw Driver

Admissible Tightening Torque*

75020-IP20-1

8IP-20

678 N-cm (60 in-lb)

*Tightening torques are calculated with a fricƟon coefficient of µ = 0.14 and develop 90% of ulƟmate yield strength

X

SPECIALS

Refer to Speed and Feed charts for recommended adjustments to speeds and feeds. Refer to page A50: 30 for deep hole drilling guidelines in this secƟon of the catalogue. Visit www.alliedmachine.com/DeepHoleGuidelines for the most up-to-date informaƟon and procedures. Factory technical assistance is available for your specific applicaƟons through our ApplicaƟon Engineering Team. email: engineering.eu@alliedmachine.com WARNING

MounƟng screws sold in mulƟples of 4 = Metric (mm) = Imperial (in)

www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com

A50: 7