A92-ACP_EU-EN

DRILLING | AccuPort 432® Port Contour Cutters

Recommended Drilling Data | Metric (mm) Carbide

A

Speed (m/min)

Feed Rate (mm/rev) by Tube Size and T-A® Insert Series

DRILLING

Tube No. 4 - 5

Tube No. 6 - 8

Tube No. 10

Tube No. 12 - 16

Tube No. 20 - 24

Hardness (BHN) 100 - 150

T-A Series Y - Z

T-A Series 0

T-A Series 1

T-A Series 2

T-A Series 3

ISO Material

Grade C 1, C5

TiN TiAlN AM200®

Free-Machining Steel 1118, 1215, 12L14, etc.

98 85 79 91 79 73 64 79 73 64 55 76 70 64 61 52 49 43 37 73 61 55 49 37 24 18 49 37 98 82 73 64 55

128 110 104 119 104

146 126 119 137 119 108

0.020

0.30 0.28 0.25 0.25 0.25 0.23 0.23 0.25 0.23 0.23 0.20 0.25 0.23 0.23 0.20 0.18 0.23 0.20 0.18 0.28 0.25 0.23 0.18 0.18 0.18 0.15 0.23 0.20 0.30 0.28 0.23 0.20 0.18 0.38 0.33

0.38 0.36 0.33 0.33 0.33 0.30 0.30 0.33 0.30 0.30 0.28 0.33 0.30 0.30 0.28 0.25 0.25 0.23 0.20 0.36 0.30 0.28 0.23 0.23 0.23 0.20 0.30 0.28 0.38 0.33 0.30 0.28 0.25 0.46 0.41

0.46 0.41 0.38 0.43 0.41 0.38 0.38 0.41 0.38 0.38 0.36 0.41 0.38 0.38 0.36 0.33 0.30 0.28 0.25 0.41 0.36 0.30 0.28 0.28 0.28 0.25 0.36 0.30 0.48 0.43 0.38 0.33 0.28 0.51 0.46

0.53 0.48 0.43 0.48 0.46 0.43 0.43 0.46 0.43 0.43 0.41 0.46 0.43 0.43 0.41 0.38 0.38 0.36 0.30 0.46 0.41 0.36 0.33 0.33 0.33 0.30 0.41 0.36 0.58 0.53 0.46 0.38 0.33 0.56 0.51

150 - 200 C1, C5 200 - 250 C1, C5 85 - 125 C1, C5 125 - 175 C1, C5 175 - 225 C1, C5 225 - 275 C1, C5 125 - 175 C1, C5 175 - 225 C1, C5 225 - 275 C1, C5 275 - 325 C1, C5 125 - 175 C1, C5 175 - 225 C1, C5 225 - 275 C1, C5 275 - 325 C1, C5 325 - 375 C1, C5 225 - 300 C1, C5 300 - 350 C1, C5 350 - 400 C1, C5 100 - 150 C1, C5 150 - 250 C1, C5 250 - 350 C1, C5 150 - 200 C1, C5 200 - 250 C1, C5 140 - 220 C2 220 - 310 C2 185 - 275 C2 275 - 350 C2 120 - 150 C2, C3 150 - 200 C2, C3 200 - 220 C2, C3 220 - 260 C2, C3 260 - 320 C2, C3

0.18 0.15

Low-Carbon Steel

0.20 0.18 0.15 0.13

1010, 1020, 1025, 1522,

B

1144, etc.

94 82

94

Medium-Carbon Steel 1030, 1040, 1050, 1527,

104

119 108

0.18 0.15 0.15 0.13 0.18 0.15 0.15 0.13 0.10

94 82 70 99 91 82 76 67 61 55 49 94 76 70 67 52 32 26 64 49

BORING

1140, 1151, etc.

94 81

Alloy Steel

114 105

P

4140, 5140, 8640, etc.

94 87 78 73 62 56 87 81 78 59 36 29 73 46

High-Strength Alloy

0.15 0.13 0.10 0.20 0.15 0.13 0.10 0.10 0.10 0.10 0.18 0.15

4340, 4330V, 300M, etc.

C

Structural Steel

108

REAMING

A36, A285, A516, etc.

Tool Steel

H-13, H-21, A-4, 0-2, S-3, etc.

High-Temp Alloy

S

Hastelloy B, Inconel 600, etc.

Stainless Steel 400 Series

M

416, 420, etc.

D

Nodular, Grey, Ductile Cast Iron

140 122 110

152 146 131 113 102

0.20 0.18 0.15 0.13 0.13 0.25 0.23

BURNISHING K

94 82

Aluminium

30

C2 C2

366 244

457 305

- -

N

180

Formulas

1. RPM

= (318.47 • m/min) / DIA

2. m/min = RPM • 0.003 • DIA

3. IPM = RPM • mm/rev

where:

where:

where:

E

RPM

= revolutions per minute (rev/min)

m/min = speed (m/min)

IPM = feed rate

m/min = speed (m/min)

RPM

= revolutions per minute (rev/min)

RPM

= revolutions per minute (rev/min)

DIA = finish diameter of drill (mm)

DIA = diameter of drill (mm)

mm/rev = feed rate (mm/rev)

THREADING

The table and equations on this page are found in the Machinery’s Handbook . Permission to simplify and print the equations is granted by the Editor of the Machinery’s Handbook .

X

SPECIALS

IMPORTANT: The speeds and feeds listed above are a general starting point for all applications. Refer to the Coolant Recommendation charts for coolant requirements to run at the recommended speeds and feeds. Factory technical assistance is also available through our Application Engineering Team. email: engineering.eu@alliedmachine.com Due to potential chip formation issues, contact our Application Engineering Team for assistance machining materials marked with a .

A92: 32

www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com