CAT-SET

DRILLING | T-A Pro® High PenetraƟon Replaceable Insert Drilling System

Recommended Drilling Data | Imperial (in)

T-A PRO | HIGH-SPEED STEEL

Feed Rate (IPR) by Diameter

Y / Z Series 0 Series

1 Series 0.6947" - 0.9596"

2 Series 0.9597" - 1.3797"

3 Series 1.3798" - 1.8820"

Hardness (BHN)

Insert Grade

Speed (SFM)

0.3739" - 0.4998"

0.4999" - 0.6946"

ISO Material

120 - 150 X 150 - 200 X 200 - 220 X 220 - 260 X 260 - 320 X

300 275 240 215 175 600 300 900 600 300 250 485 320

0.007 0.006 0.006 0.005 0.004 0.008 0.008 0.009 0.005 0.006 0.005 0.007 0.002 0.003 0.003 0.003 0.003 0.005 0.004 0.003 0.002 0.003 0.002

0.012 0.011 0.009 0.007 0.006 0.013 0.013 0.013 0.007 0.011 0.007 0.012 0.003 0.007 0.006 0.007 0.006 0.008 0.007 0.006 0.005 0.006 0.005

0.016 0.014 0.012 0.009 0.007 0.016 0.016 0.017 0.010 0.014 0.009 0.016 0.006 0.008 0.007 0.008 0.007 0.009 0.008 0.008 0.007 0.008 0.007

0.020 0.018 0.016 0.012 0.009 0.020 0.018 0.020 0.013 0.018 0.012 0.020 0.008 0.010 0.008 0.010 0.008 0.010 0.008 0.009 0.008 0.009 0.008

0.024 0.022 0.018 0.014 0.012 0.022 0.022 0.024 0.016 0.022 0.014 0.024 0.010 0.012 0.010 0.012 0.010 0.014 0.012 0.012 0.010 0.012 0.010

SG / Nodular Cast Iron

K

A25

30

X X X X

Cast Aluminum

180

30

Wrought Aluminum

180

N

100 - 200 X 200 - 250 X

Aluminum Bronze

Brass

100

X X

Copper

60

140 - 220 X 220 - 310 X 140 - 220 X 220 - 310 X 185 - 275 X 275 - 350 X

45 40 60 50

High-Temp Alloy Hastelloy® B, Inconel® 600, etc.

Titanium Alloy

S

125 110

Aerospace Alloy S82

400 500 600

X X

60 45 75 45

Wear Plate Hardox®, AR400, T-1, etc.

— — — — — — —

H

300 - 400 X 400 - 500 X

Hardened Steel

Contact our ApplicaƟon Engineering department for assistance when machining these materials.

7xD and 10xD Adjustment Example (0.80 Adjustment) Data • Adjustment Value Speed/Feed (7xD) 200 SFM • 0.80 = 160 SFM 0.008 IPR • 0.80 = 0.0064 IPR

12xD and 15xD Adjustment Example (0.70 Adjustment) Speed • Adjustment Value Speed/Feed (12xD) 200 SFM • 0.70 = 140 SFM 0.008 IPR • 0.70 = 0.0056 IPR

Coolant RecommendaƟons

Stub, 3xD, 5xD

7xD, 10xD

12xD, 15xD

Pressure PSI

Flow Rate GPM

Pressure PSI

Flow Rate GPM

Pressure PSI

Flow Rate GPM

Series

Y Z 0 1 2 3

450 450 350 300 250 200

4 4 6 8

550 550 450 400 350 300

6 6 9

650 650 550 500 450 400

8 8

12 12 16 18

10 13 14

10 12

Tool failure can cause serious injury. To prevent: - When using holders without support bushing, use a short T-A Pro holder to establish an iniƟal hole that is a minimum of 2 diameters deep. - Do not rotate tool holders more than 50 RPM unless it is engaged with the workpiece or fixture. Visit www.alliedmachine.com/DeepHoleGuidelines for the most up-to-date informaƟon and procedures. Factory technical assistance is available for your specific applicaƟons through our ApplicaƟon Engineering department : appeng@alliedmachine.com . WARNING IMPORTANT: The speeds and feeds listed above are a general starƟng point for all applicaƟons. Refer to the coolant recommendaƟon chart for coolant requirements to run at the recommended speeds and feeds. Factory technical assistance is available through our ApplicaƟon Engineering department. For 7xD, 10xD, 12xD, and 15xD holder lengths, see adjustment example above.

www.alliedmachine.com | 1.330.343.4283

A25: 58