CAT-SET

DRILLING | T-A® Replaceable Insert Drilling System

0 Series: 12.98 mm - 17.67 mm (0.5110" - 0.6959")

T-A® Drill Holders

A30

Stub Length

Imperial Flange Shank Holders

Body

Shank

L 2

L 4

L 3

L 1

L 5

D 2

P 1

Flute

Series

Length

Part No.

21000S-075F 22000S-075F 24000S-075F 25000S-075F 21005S-075F 22005S-075F 24005S-075F 25005S-075F 24000H-075F 24500H-075F 25000H-075F 26000H-075F 26500H-075F 24005H-075F 25005H-075F 26005H-075F

Stub Short

0.910 1.875 1.982 3.905 2.030 1.220 2.500 2.607 4.530 2.030 2.345 3.625 3.732 5.655 2.030 0.945 1.875 1.982 3.905 2.030 1.195 2.500 2.607 4.530 2.030 2.320 3.625 3.732 5.655 2.030 2.987 3.625 3.732 5.655 2.030 3.992 4.630 4.737 6.660 2.030 7.487 8.125 8.232 10.155 2.030 9.937 10.575 10.682 12.605 2.030 3.034 3.625 3.732 5.655 2.030

3/4 1/8 NPT 3/4 1/8 NPT 3/4 1/8 NPT 3/4 1/8 NPT 3/4 1/8 NPT 3/4 1/8 NPT 3/4 1/8 NPT 3/4 1/8 NPT 3/4 1/8 NPT 3/4 1/8 NPT 3/4 1/8 NPT 3/4 1/8 NPT 3/4 1/8 NPT 3/4 1/8 NPT 3/4 1/8 NPT 3/4 1/8 NPT

0

Standard

Extended 4.345 5.625 5.732 7.655 2.030

Stub Short

Straight

0.5

Standard

Extended 4.320 5.625 5.732 7.655 2.030

Standard

Standard Plus

Extended 4.987 5.625 5.732 7.655 2.030

0

Long

Long Plus Standard

Helical

Extended 5.034 5.625 5.732 7.655 2.030

0.5

Long

7.534 8.125 8.232 10.155 2.030

NOTE: Stub length holders have a 3.175 mm (1/8") side pipe tap (P 2 ). NOTE: 0.5 series inserts fit into both 0 and 0.5 series holders. However, 0 series inserts ONLY fit into 0 series holders. See page A30: 7 for visual .

Connection Accessories

Nylon Locking Screws 72556N-IP8-1 72567N-IP8-1

Preset Torque Hand Driver

Admissible Tightening Torque* 175 N-cm (15.5 in-lbs) 175 N-cm (15.5 in-lbs)

Series

Insert Screws 72556-IP8-1 72567-IP8-1

Insert Driver

Replacement Tips

0

8IP-8 8IP-8

8IP-8TL 8IP-8TL

8IP-8B 8IP-8B

0.5

*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength.

Refer to Speed and Feed charts for recommended adjustments to speeds and feeds. Refer to page A30: 146 for deep hole drilling guidelines in this section of the catalog. Visit www.alliedmachine.com/DeepHoleGuidelines for the most up-to-date information and procedures. Factory technical assistance is available for your specific applications through our Application Engineering department : appeng@alliedmachine.com. WARNING

A30: 113 - 139

A30: 33 - 39

A30: 46 & 112

Key on A30: 2

Screws sold in multiples of 10. = Metric ( mm) = Imperial (in)

www.alliedmachine.com | 1.330.343.4283

A30: 42