CAT-SET

DRILLING | T-A® Replaceable Insert Drilling System

0 Series: 12.98 mm - 17.67 mm (0.5110" - 0.6959")

T-A® Drill Holders

Straight Shank Holders

Body

Shank

L 2

L 4

L 3

L 1

L 5

D 2

P 1

Flute

Series

Length

Part No.

A30

22000S-075L 24000S-075L 25000S-075L 26000S-075L 27000S-075L 29000S-075L 22005S-075L 24005S-075L 25005S-075L

Short 1.218 2.188 2.295 4.563 2.375 2.343 3.313 3.420 5.688 2.375 6.843 7.813 7.920 10.188 2.375 11.468 12.438 12.545 14.813 2.375 15.093 16.063 16.170 18.438 2.375 1.194 2.188 2.295 4.563 2.375 2.319 3.313 3.420 5.688 2.375 Extended 4.343 5.313 5.420 7.688 2.375 Long XL 3XL Short Standard Extended 4.319 5.313 5.420 7.688 2.375 Standard

3/4 1/8 NPT 3/4 1/8 NPT 3/4 1/8 NPT 3/4 1/8 NPT 3/4 1/8 NPT 3/4 1/8 NPT 3/4 1/8 NPT 3/4 1/8 NPT 3/4 1/8 NPT 3/4 1/8 NPT

0

Straight

0.5

Long 26005S-075L NOTE: 0.5 series inserts fit into both 0 and 0.5 series holders. However, 0 series inserts ONLY fit into 0 series holders. See page A30: 7 for visual . 6.819 7.813 7.920 10.188 2.375

ER Collet Holders

Body

Collet Nut without Retaining Ring

L 2

L 4

L 3

L 1

ER

Series

Part No.

21000S-16ER 21000S-20ER

41.2 41.2

48.1 48.1

50.8 50.8

75.3 79.3

ER-16 ER-20

ER-16N

0

ER-20N NOTE: 0.5 series inserts fit into both 0 and 0.5 series holders. However, 0 series inserts ONLY fit into 0 series holders. See page A30: 7 for visual .

Connection Accessories

Nylon Locking Screws 72556N-IP8-1 72567N-IP8-1

Preset Torque Hand Driver

Admissible Tightening Torque* 175 N-cm (15.5 in-lbs) 175 N-cm (15.5 in-lbs)

Series

Insert Screws 72556-IP8-1 72567-IP8-1

Insert Driver

Replacement Tips

0

8IP-8 8IP-8

8IP-8TL 8IP-8TL

8IP-8B 8IP-8B

0.5

*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength.

Refer to Speed and Feed charts for recommended adjustments to speeds and feeds. Refer to page A30: 146 for deep hole drilling guidelines in this section of the catalog. Visit www.alliedmachine.com/DeepHoleGuidelines for the most up-to-date information and procedures. Factory technical assistance is available for your specific applications through our Application Engineering department : appeng@alliedmachine.com. WARNING

A30: 113 - 139

A30: 33 - 39

A30: 46 & 112

Key on A30: 2

Screws sold in multiples of 10. = Metric ( mm) = Imperial (in)

A30: 45

www.alliedmachine.com | 1.330.343.4283