CAT-SET

DRILLING | T-A® Replaceable Insert Drilling System

T-A FLAT BOTTOM | HIGH-SPEED STEEL Feed Rate ( mm/rev ) by Diameter

Y/Z Series

0 Series

1 Series

2 Series

3 Series

4 Series

0.3740" - 0.5109"

0.5110" - 0.6959"

0.6900" - 0.9609"

0.9610" - 1.3809"

1.3530" - 1.8829"

1.8500" - 2.5709"

0.006 0.006 0.005 0.005 0.005 0.004 0.004 0.005 0.004 0.004 0.004 0.005 0.004 0.004 0.004 0.003 0.004 0.003 0.003 0.005 0.004 0.004 0.004 0.004 0.005 0.004 0.005 0.004 0.005 0.004 0.007 0.006 0.006 0.005 0.004 0.007 0.007 0.007 0.007 0.005 0.004 0.006 0.002 0.003 0.003 0.003 0.003 0.005 0.004

0.009 0.009 0.009 0.008 0.008 0.007 0.007 0.008 0.007 0.007 0.006 0.007 0.007 0.006 0.005 0.005 0.006 0.006 0.005 0.009 0.008 0.007 0.005 0.005 0.007 0.006 0.007 0.006 0.007 0.006 0.012 0.011 0.009 0.007 0.006 0.011 0.011 0.011 0.011 0.009 0.006 0.010 0.003 0.006 0.005 0.006 0.005 0.007 0.006

0.011 0.011 0.011 0.010 0.010 0.009 0.009 0.010 0.009 0.009 0.008 0.009 0.009 0.009 0.008 0.008 0.008 0.008 0.007 0.010 0.009 0.008 0.007 0.007 0.008 0.007 0.008 0.007 0.008 0.007 0.016 0.014 0.012 0.009 0.007 0.014 0.014 0.014 0.014 0.012 0.008 0.014 0.006 0.007 0.006 0.007 0.006 0.008 0.007

0.014 0.014 0.014 0.013 0.013 0.012 0.012 0.013 0.012 0.012 0.010 0.012 0.012 0.012 0.010 0.010 0.009 0.009 0.008 0.012 0.010 0.009 0.009 0.009 0.010 0.009 0.010 0.009 0.010 0.009 0.020 0.018 0.016 0.012 0.009 0.017 0.016 0.017 0.016 0.016 0.010 0.017 0.008 0.009 0.007 0.009 0.007 0.010 0.009

0.016 0.016 0.015 0.015 0.015 0.014 0.014 0.015 0.014 0.014 0.013 0.013 0.013 0.013 0.012 0.012 0.010 0.010 0.009 0.015 0.013 0.012 0.010 0.009 0.012 0.010 0.012 0.010 0.012 0.010 0.024 0.022 0.018 0.014 0.012 0.018 0.017 0.018 0.017 0.020 0.012 0.021 0.010 0.010 0.008 0.010 0.008 0.012 0.010

0.018 0.018 0.017 0.017 0.016 0.016 0.015 0.018 0.017 0.017 0.015 0.016 0.016 0.016 0.015 0.014 0.012 0.012 0.011 0.017 0.016 0.015 0.012 0.011 0.014 0.011 0.014 0.011 0.014 0.011 0.027 0.025 0.021 0.017 0.014 0.019 0.019 0.019 0.019 0.024 0.015 0.025 0.014 0.012 0.010 0.012 0.010 0.015 0.012

A30

— — —

— — —

— — —

— — —

— — —

— — —

0.005 0.004

0.007 0.006

0.008 0.007

0.011 0.009

0.015 0.011

0.003 0.002

Tool failure can cause serious injury. To prevent: - When using holders without support bushing, use a short T-A holder to establish an iniƟal hole that is a minimum of 2 diameters deep. - Do not rotate tool holders more than 50 RPM unless it is engaged with the workpiece or fixture. Visit www.alliedmachine.com/DeepHoleGuidelines for the most up-to-date informaƟon and procedures. Factory technical assistance is available for your specific applicaƟons through our ApplicaƟon Engineering department : appeng@alliedmachine.com . WARNING

www.alliedmachine.com | 1.330.343.4283

A30: 136