CAT-SET
DRILLING | T-A® Replaceable Insert Drilling System
Coolant RecommendaƟons | Metric (mm)
T-A | CARBIDE
Y/Z Series 9.50 mm - 12.97 mm
0 Series
1 Series
2 Series
3 Series
12.98 mm - 17.67 mm
17.53 mm - 24.40 mm
24.41 mm - 35.06 mm
34.37 mm - 47.82 mm
Pressure or Flow Rate
ISO Material
Free-Machining Steel 1118, 1215, 12L14, etc. Low-Carbon Steel 1010, 1020, 1025, 1522, etc. Medium-Carbon Steel 1030, 1040, 1050, 1527, etc. Alloy Steel 4140, 5140, 8640, etc. High-Strength Alloy 4340, 4330V, 300M, etc. Structural Steel A36, A285, A516, etc. Tool Steel H-13, H-21, A-4, S-3, etc. Stainless Steel 400 Series 416, 420, etc. Stainless Steel 300 Series 304, 316, 17-4PH, etc. Super Duplex Stainless Steel
BAR LPM BAR LPM BAR LPM BAR LPM BAR LPM BAR LPM BAR LPM BAR LPM BAR LPM BAR LPM BAR LPM BAR LPM BAR LPM BAR LPM BAR LPM BAR LPM BAR LPM BAR LPM BAR LPM BAR LPM BAR LPM BAR LPM
17 - 20
17
15
15
20
12.2
16.3
25.2
41.5
71.9
18
11
11
12
9
11.4
13.3
20.6
36.5
62.0
17
10
10
10
8
11.3
12.5
20.0
33.8
57.0
17
9
10
8
7
P
11.1
12.3
19.3
30.0
55.8
15
5
4
3
3
10.4
9.1
12.6
18.8
33.6
16
9
8
7
5
10.8
12.0
17.5
27.8
47.1
A30
15
5
5
3
3
10.4 22.7
9.1
13.6 17.9 26.3 17.9 26.3 17.9 26.3 6.2 15.4 6.2 15.4 21.7 16.5 25.2 21.7 16.5 25.2 29 29 21.7 29
19.7 17.2 44.2 17.2 44.2 17.2 44.2 6.2 26.5 6.2 26.5 19.6 47.2 19.6 47.2 15.2 41.5 19.6 47.2 15.2 41.5
36.5 13.1
16.5 16.3 16.5 16.3 16.5 16.3 7.2 10.8 7.2 10.8 18.8 16.5 16.3 18.8 16.5 16.3 22 22 18.8 22
13
75
22.7
13.1
M
13
75
22.7
13.1
13
75
SG / Nodular Cast Iron
15.5 10.7 15.5 10.7 24.1 13.4 24.1 13.4 12.2 24.1 13.4 20
5.5 48.7 5.5 48.7 13.8
K
Grey / White Iron
Cast Aluminum
77
Wrought Aluminum
13.8
77 12
Aluminum Bronze
N
71.9 13.8
Brass
77 12
Copper
20
12.2
71.9
High-Temp Alloy Hastelloy® B, Inconel® 600, etc.
17
11
12
11
9
11.1
13.5
21.9
35.4
62.0
Titanium Alloy
17
11
12
11
9
S
11.1
13.5
21.9
35.4
62.0
Aerospace Alloy S82
17
11
12
11
9
11.1 14.5 10.4 14.5 10.4
13.5
21.9 4.8 13.6 4.8 13.6
35.4 3.4 19.7 3.4 19.7
62.0 3.1 36.5 3.1 36.5
Wear Plate Hardox®, AR400, T-1, etc.
5.2 9.1 5.2 9.1
H
Hardened Steel
Contact our ApplicaƟon Engineering department for assistance when machining these materials.
Deep Hole Drilling Coolant Adjustment
Recommended Coolant Example If the recommended pressure and flow is 12 bar and 22 LPM for a standard length holder, then the adjusted pressure and flow for a 3XL holder would be 36 bar and 66 LPM. 12 • 3 = 36 bar 22 • 3 = 66 LPM
Holder Length
Long Plus
Extended Long
XL 3XL
Pressure and Flow
1.3
1.5
2
2
3
IMPORTANT: The coolant pressure and flow rate recommendaƟons above represent a good approximaƟon to obtain opƟmum tool life and chip evacuaƟon at Allied Machine recommended speeds and feeds. If lower coolant capabiliƟes exist in a drilling applicaƟon, the T-A® drilling system will sƟll funcƟon at reduced penetraƟon rates. Contact our ApplicaƟon Engineering department for a more specific recommendaƟon of coolant requirements and/or speeds and feeds. Tool failure can cause serious injury. To prevent: - When using holders without support bushing, use a short T-A holder to establish an iniƟal hole that is a minimum of 2 diameters deep. - Do not rotate tool holders more than 50 RPM unless it is engaged with the workpiece or fixture. Visit www.alliedmachine.com/DeepHoleGuidelines for the most up-to-date informaƟon and procedures. Factory technical assistance is available for your specific applicaƟons through our ApplicaƟon Engineering department : appeng@alliedmachine.com . WARNING www.alliedmachine.com | 1.330.343.4283 A30: 142
Made with FlippingBook - Online catalogs