A20-XTP_US-EN

DRILLING | GEN3SYS® XT Pro and XT High Penetration Replaceable Insert Drilling System

11

GEN3SYS XT Pro Drill Insert Holders 11 Series | Diameter Range: 0.4331" - 0.4723" (11.00 mm - 11.99 mm)

A

DRILLING

L 1

L 7

L 4

D 2

L 2

B

L 3

Body

Shank

BORING

L 2

L 4

L 3

L 1

L 7

D 2

Flute

Length

Flat YES NO YES NO YES NO YES NO YES NO YES NO YES NO YES NO YES NO YES NO

Part No.

HXT0311S-063F HXT0311S-063C HXT0511S-063F HXT0511S-063C HXT0711S-063F HXT0711S-063C HXT1011S-063F HXT1011S-063C HXT1211S-063F HXT1211S-063C HXT0311S-16FM HXT0311S-16CM HXT0511S-16FM HXT0511S-16CM HXT0711S-16FM HXT0711S-16CM HXT1011S-16FM HXT1011S-16CM HXT1211S-16FM HXT1211S-16CM

3xD 3xD 5xD 5xD 7xD 7xD

1-27/64 1-27/64 2-23/64 2-23/64 3-19/64 3-19/64 4-23/32 4-23/32 5-43/64 5-43/64

2-29/64 2-29/64 3-13/32 3-13/32 4-11/32 4-11/32 5-49/64 5-49/64 6-45/64 6-45/65

2-17/32 2-17/32 3-31/64 3-31/64 4-27/64 4-27/64 5-27/32 5-27/32 6-25/32 6-25/32

4-21/64 4-21/64 5-9/32 5-9/32 6-7/32 6-7/32 7-41/64 7-41/64 8-37/64 8-37/64

1-7/8 1-7/8 1-7/8 1-7/8 1-7/8 1-7/8 1-7/8 1-7/8 1-7/8 1-7/8

5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8

Straight

C

10xD 10xD 12xD 12xD

REAMING

3xD 3xD 5xD 5xD 7xD 7xD

36.0 36.0 60.0 60.0 83.7 83.7

62.6 62.6 86.6 86.6

64.4 64.4 88.4 88.4

110.6 110.6 134.6 134.6 158.6 158.6 194.6 194.6 194.6 194.6

48.0 48.0 48.0 48.0 48.0 48.0 48.0 48.0 48.0 48.0

16.0 16.0 16.0 16.0 16.0 16.0 16.0 16.0 16.0 16.0

Straight

110.6 110.6 146.6 146.6 146.6 146.6

112.4 112.4 148.4 148.4 148.4 148.4

10xD 10xD 12xD 12xD

119.9 119.9 119.9 119.9

D

BURNISHING

E

THREADING

Connection Accessories

Admissible Tightening Torque* 4.4 in-lbs (50 N-cm)

Insert Screws 71843-IP6-1

Insert Driver

Preset Torque Hand Driver

Replacement Tips

8IP-6

8IP-6TL

8IP-6B

X

*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength

SPECIALS

Refer to Speed and Feed charts for recommended adjustments to speeds and feeds. Refer to page A20: 86 for deep hole drilling guidelines in this section of the catalog. Visit www.alliedmachine.com/DeepHoleGuidelines for the most up-to-date information and procedures. Factory technical assistance is available for your specific applications through our Application Engineering Team. ext: 7611 | email: appeng@alliedmachine.com WARNING

Screws sold in multiples of 10 = Imperial (in) = Metric (mm)

www.alliedmachine.com | 1.330.343.4283

A20: 13