A20-XTP_US-EN

DRILLING | GEN3SYS® XT Pro and XT High Penetration Replaceable Insert Drilling System

12

GEN3SYS XT Pro Drill Insert Holders

A

12 Series | Diameter Range: 0.4724" - 0.5117" (12.00 mm - 12.99 mm)

DRILLING

L 1

L 7

L 4

D 2

L 2

B

L 3

Body

Shank

BORING

L 2

L 4

L 3

L 1

L 7

D 2

Flute

Length

Flat YES NO YES NO YES NO YES NO YES NO YES NO YES NO YES NO YES NO YES NO

Part No.

HXT0312S-075F HXT0312S-075C HXT0512S-075F HXT0512S-075C HXT0712S-075F HXT0712S-075C HXT1012S-075F HXT1012S-075C HXT1212S-075F HXT1212S-075C HXT0312S-20FM HXT0312S-20CM HXT0512S-20FM HXT0512S-20CM HXT0712S-20FM HXT0712S-20CM HXT1012S-20FM HXT1012S-20CM HXT1212S-20FM HXT1212S-20CM

3xD 3xD 5xD 5xD 7xD 7xD

1-17/32 1-17/32 2-9/16 2-9/16 3-37/64 3-37/64 5-7/64 5-7/64 6-9/64 6-9/64

2-5/8 2-5/8

2-45/64 2-45/64 3-47/64 3-47/64

4-21/32 4-21/32 5-43/64 5-43/64 6-11/16 6-11/16 8-15/64 8-15/64

2-1/32 2-1/32 2-1/32 2-1/32 2-1/32 2-1/32 2-1/32 2-1/32 2-1/32 2-1/32

3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4

3-41/64 3-41/64 4-21/32 4-21/32 6-13/64 6-13/64 7-7/32 7-7/32

Straight

4-3/4 4-3/4

C

10xD 10xD 12xD 12xD

6-9/32 6-9/32 7-5/16 7-5/16

9-1/4 9-1/4 116.6 116.6 142.5 142.5 168.3 168.3 207.5 207.5 233.5 233.5

REAMING

3xD 3xD 5xD 5xD 7xD 7xD

39.0 39.0 65.0 65.0 90.9 90.9

66.6 66.6 92.5 92.5

68.7 68.7 94.7 94.7

50.0 50.0 50.0 50.0 50.0 50.0 50.0 50.0 50.0 50.0

20.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0

Straight

118.3 118.3 157.5 157.5 183.5 183.5

120.7 120.7 159.7 159.7 185.7 185.7

10xD 10xD 12xD 12xD

129.9 129.9 156.0 156.0

D

BURNISHING

E

THREADING

Connection Accessories

Admissible Tightening Torque* 7.4 in-lbs (84 N-cm)

Insert Screws

Nylon Locking Screws

Insert Driver

Replacement Tips

Preset Torque Hand Driver

7247-IP7-1

7247N-IP7-1

8IP-7

8IP-7TL

8IP-7B

X

*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength

SPECIALS

Refer to Speed and Feed charts for recommended adjustments to speeds and feeds. Refer to page A20: 86 for deep hole drilling guidelines in this section of the catalog. Visit www.alliedmachine.com/DeepHoleGuidelines for the most up-to-date information and procedures. Factory technical assistance is available for your specific applications through our Application Engineering Team. ext: 7611 | email: appeng@alliedmachine.com WARNING

Screws sold in multiples of 10 = Imperial (in) = Metric (mm)

www.alliedmachine.com | 1.330.343.4283

A20: 17