A20-XTP_US-EN

DRILLING | GEN3SYS® XT Pro and XT High Penetration Replaceable Insert Drilling System

15

GEN3SYS XT Pro Drill Insert Holders 15 Series | Diameter Range: 0.5906" - 0.6298" (15.00 mm - 15.99 mm)

A

L 1

DRILLING

L 7

L 4

D 2

L 2

B

L 3

Body

Shank

BORING

L 2

L 4

L 3

L 1

L 7

D 2

Flute

Length

Flat YES NO YES NO YES NO YES NO YES NO YES NO YES NO YES NO YES NO YES NO

Part No.

HXT0315S-075F HXT0315S-075C HXT0515S-075F HXT0515S-075C HXT0715S-075F HXT0715S-075C HXT1015S-075F HXT1015S-075C HXT1215S-075F HXT1215S-075C HXT0315S-20FM HXT0315S-20CM HXT0515S-20FM HXT0515S-20CM HXT0715S-20FM HXT0715S-20CM HXT1015S-20FM HXT1015S-20CM HXT1215S-20FM HXT1215S-20CM

3xD 3xD 5xD 5xD 7xD 7xD

1-57/64 1-57/64 3-9/64 3-9/64 4-13/32 4-13/32 6-19/64 6-19/64 7-9/16 7-9/16

2-61/64 2-61/64 4-13/64 4-13/64 5-15/32 5-15/32 7-23/64 7-23/64 8-39/64 8-39/64

3-3/64 3-3/64 4-5/16 4-5/16 5-37/64 5-37/64 7-29/64 7-29/64

4-63/64 4-63/64 6-15/64 6-15/64

2-1/32 2-1/32 2-1/32 2-1/32 2-1/32 2-1/32 2-1/32 2-1/32 2-1/32 2-1/32

3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4

Straight

7-1/2 7-1/2

C

10xD 10xD 12xD 12xD

9-25/64 9-25/64

8-23/32 10-41/64 8-21/32 10-41/64

REAMING

3xD 3xD 5xD 5xD 7xD 7xD

48.0 48.0 79.8 79.8

75.0 75.0

77.5 77.5

125.0 125.0 156.8 156.8 188.9 188.9 236.9 236.9 269.0 269.0

50.0 50.0 50.0 50.0 50.0 50.0 50.0 50.0 50.0 50.0

20.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0

106.8 106.8 138.9 138.9 186.9 186.9 219.0 219.0

109.5 109.5 141.5 141.5 189.5 189.5 221.6 221.6

Straight

111.9 111.9 159.9 159.9 192.0 192.0

10xD 10xD 12xD 12xD

D

BURNISHING

E

THREADING

Connection Accessories

Admissible Tightening Torque* 7.4 in-lbs (84 N-cm)

Insert Screws

Nylon Locking Screws

Insert Driver

Replacement Tips

Preset Torque Hand Driver

7247-IP7-1

7247N-IP7-1

8IP-7

8IP-7TL

8IP-7B

X

*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength

SPECIALS

Refer to Speed and Feed charts for recommended adjustments to speeds and feeds. Refer to page A20: 86 for deep hole drilling guidelines in this section of the catalog. Visit www.alliedmachine.com/DeepHoleGuidelines for the most up-to-date information and procedures. Factory technical assistance is available for your specific applications through our Application Engineering Team. ext: 7611 | email: appeng@alliedmachine.com WARNING

Screws sold in multiples of 10 = Imperial (in) = Metric (mm)

www.alliedmachine.com | 1.330.343.4283

A20: 29