A20-XTP_US-EN

DRILLING | GEN3SYS® XT Pro and XT High Penetration Replaceable Insert Drilling System

16

GEN3SYS XT Pro Drill Insert Holders 16 Series | Diameter Range: 0.6299" - 0.6692" (16.00 mm - 16.99 mm)

A

L 1

DRILLING

L 7

L 4

D 2

L 2

B

L 3

Body

Shank

BORING

L 2

L 4

L 3

L 1

L 7

D 2

Flute

Length

Flat YES NO YES NO YES NO YES NO YES NO YES NO YES NO YES NO YES NO YES NO

Part No.

HXT0316S-075F HXT0316S-075C HXT0516S-075F HXT0516S-075C HXT0716S-075F HXT0716S-075C HXT1016S-075F HXT1016S-075C HXT1216S-075F HXT1216S-075C HXT0316S-20FM HXT0316S-20CM HXT0516S-20FM HXT0516S-20CM HXT0716S-20FM HXT0716S-20CM HXT1016S-20FM HXT1016S-20CM HXT1216S-20FM HXT1216S-20CM

3xD 3xD 5xD 5xD 7xD 7xD

2 2

3-13/64 3-13/64 4-17/32 4-17/32

3-5/16 3-5/16 4-21/32 4-21/32 5-63/64 5-63/64

5-15/64 5-15/64 6-9/16 6-9/16 7-29/32 7-29/32 9-29/32 9-29/32 11-1/4 11-1/4

2-1/32 2-1/32 2-1/32 2-1/32 2-1/32 2-1/32 2-1/32 2-1/32 2-1/32 2-1/32

3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4

3-11/32 3-11/32 4-11/16 4-11/16 6-11/16 6-11/16 8-1/32 8-1/32

Straight

5-7/8 5-7/8 7-7/8 7-7/8

C

10xD 10xD 12xD 12xD

8 8

9-7/32 9-7/32

9-21/64 9-21/64

REAMING

3xD 3xD 5xD 5xD 7xD 7xD

50.8 50.8 85.0 85.0

81.3 81.3

84.2 84.2

131.3 131.3 165.1 165.1 199.2 199.2 250.0 250.0 284.3 284.3

50.0 50.0 50.0 50.0 50.0 50.0 50.0 50.0 50.0 50.0

20.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0

115.1 115.1 149.2 149.2 200.0 200.0 234.3 234.3

118.2 118.2 152.0 152.0 203.2 203.2 237.2 237.2

Straight

119.0 119.0 169.9 169.9 204.0 204.0

10xD 10xD 12xD 12xD

D

BURNISHING

E

THREADING

Connection Accessories

Admissible Tightening Torque* 15.5 in-lbs (175 N-cm)

Insert Screws 72556-IP8-1

Nylon Locking Screws

Insert Driver

Replacement Tips

Preset Torque Hand Driver

72556N-IP8-1

8IP-8

8IP-8TL

8IP-8B

X

*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength

SPECIALS

Refer to Speed and Feed charts for recommended adjustments to speeds and feeds. Refer to page A20: 86 for deep hole drilling guidelines in this section of the catalog. Visit www.alliedmachine.com/DeepHoleGuidelines for the most up-to-date information and procedures. Factory technical assistance is available for your specific applications through our Application Engineering Team. ext: 7611 | email: appeng@alliedmachine.com WARNING

Screws sold in multiples of 10 = Imperial (in) = Metric (mm)

www.alliedmachine.com | 1.330.343.4283

A20: 33