A20-XTP_US-EN

DRILLING | GEN3SYS® XT Pro and XT High Penetration Replaceable Insert Drilling System

22

GEN3SYS XT Pro Drill Insert Holders 22 Series | Diameter Range: 0.8661" - 0.9448" (22.00 mm - 23.99 mm)

A

DRILLING

L 1

L 7

L 4

D 2

L 2

B

L 3

Body

Shank

BORING

L 2

L 4

L 3

L 1

L 7

D 2

Flute

Length

Flat YES NO YES NO YES NO YES NO YES NO YES NO YES NO YES NO YES NO YES NO

Part No.

HXT0322S-100F HXT0322S-100C HXT0522S-100F HXT0522S-100C HXT0722S-100F HXT0722S-100C HXT1022S-100F HXT1022S-100C HXT1222S-100F HXT1222S-100C HXT0322S-25FM HXT0322S-25CM HXT0522S-25FM HXT0522S-25CM HXT0722S-25FM HXT0722S-25CM HXT1022S-25FM HXT1022S-25CM HXT1222S-25FM HXT1222S-25CM

3xD 3xD 5xD 5xD 7xD 7xD

2-53/64 2-53/64 4-23/32 4-23/32 6-39/64 6-39/64 9-7/16 9-7/16

4-9/64 4-9/64 6-1/32 6-1/32 7-59/64 7-59/64 10-3/4 10-3/4

4-17/64 4-17/64 6-5/32 6-5/32 8-3/64 8-3/64 10-7/8 10-7/8 12-3/4 12-3/4

6-27/64 6-27/64 8-5/16 8-5/16 10-13/64 10-13/64 13-1/32 13-1/32 14-59/64 14-59/64

2-9/32 2-9/32 2-9/32 2-9/32 2-9/32 2-9/32 2-9/32 2-9/32 2-9/32 2-9/32

1 1 1 1 1 1 1 1 1 1

Straight

C

10xD 10xD

12xD 11-11/32 12-41/64 12xD 11-11/32 12-41/64

REAMING

3xD 3xD 5xD 5xD 7xD 7xD

72.0 72.0

105.1 105.1 153.2 153.2 201.2 201.2 273.0 273.0 321.2 321.2

108.3 108.3 156.2 156.2 204.2 204.2 276.2 276.2 324.2 324.2

161.1 161.1 209.2 209.2 257.2 257.2 329.0 329.0 377.2 377.2

56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0

25.0 25.0 25.0 25.0 25.0 25.0 25.0 25.0 25.0 25.0

120.0 120.0 167.9 167.9 239.9 239.9 288.0 288.0

Straight

10xD 10xD 12xD 12xD

D

BURNISHING

E

THREADING

Connection Accessories

Admissible Tightening Torque* 27.0 in-lbs (305 N-cm)

Insert Screws

Nylon Locking Screws

Insert Driver

Replacement Tips

Preset Torque Hand Driver

739-IP9-1

739N-IP9-1

8IP-9

8IP-9TL

8IP-9B

X

*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength

SPECIALS

Refer to Speed and Feed charts for recommended adjustments to speeds and feeds. Refer to page A20: 86 for deep hole drilling guidelines in this section of the catalog. Visit www.alliedmachine.com/DeepHoleGuidelines for the most up-to-date information and procedures. Factory technical assistance is available for your specific applications through our Application Engineering Team. ext: 7611 | email: appeng@alliedmachine.com WARNING

Screws sold in multiples of 10 = Imperial (in) = Metric (mm)

www.alliedmachine.com | 1.330.343.4283

A20: 49