A20-XTP_US-EN

DRILLING | GEN3SYS® XT Pro and XT High Penetration Replaceable Insert Drilling System

24

GEN3SYS XT Pro Drill Insert Holders 24 Series | Diameter Range: 0.9449" - 1.0235" (24.00 mm - 25.99 mm)

A

L 1

DRILLING

L 7

L 4

D 2

L 2

B

L 3

Body

Shank

BORING

L 2

L 4

L 3

L 1

L 7

D 2

Flute

Length

Flat YES NO YES NO YES NO YES NO YES NO YES NO YES NO YES NO YES NO YES NO

Part No.

HXT0324S-100F HXT0324S-100C HXT0524S-100F HXT0524S-100C HXT0724S-100F HXT0724S-100C HXT1024S-100F HXT1024S-100C HXT1224S-100F HXT1224S-100C HXT0324S-25FM HXT0324S-25CM HXT0524S-25FM HXT0524S-25CM HXT0724S-25FM HXT0724S-25CM HXT1024S-25FM HXT1024S-25CM HXT1224S-25FM HXT1224S-25CM

3xD 3xD 5xD 5xD 7xD 7xD

3-1/16 3-1/16 5-7/64 5-7/64 7-5/32 7-5/32

4-31/64 4-31/64 6-17/32 6-17/32 8-37/64 8-37/64

4-19/32 4-19/32 6-41/64 6-41/64

6-49/64 6-49/64 8-13/16 8-13/16

2-9/32 2-9/32 2-9/32 2-9/32 2-9/32 2-9/32 2-9/32 2-9/32 2-9/32 2-9/32

1 1 1 1 1 1 1 1 1 1

Straight

8-11/16 10-55/64 8-11/16 10-55/64

C

10xD 10-15/64 11-41/64 11-49/64 13-59/64 10xD 10-15/64 11-41/64 11-49/64 13-59/64

12xD 12xD

12-9/32 13-11/16 13-51/64 15-31/32 12-9/32 13-11/16 13-15/64 15-31/32

REAMING

3xD 3xD 5xD 5xD 7xD 7xD

78.0 78.0

113.9 113.9 165.9 165.9 217.9 217.9 295.7 295.7 347.7 347.7

116.8 116.8 168.7 168.7 220.7 220.7 298.7 298.7 350.7 350.7

169.9 169.9 221.9 221.9 273.9 273.9 351.7 351.7 403.7 403.7

56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0

25.0 25.0 25.0 25.0 25.0 25.0 25.0 25.0 25.0 25.0

130.0 130.0 181.9 181.9 259.9 259.9 312.0 312.0

Straight

10xD 10xD 12xD 12xD

D

BURNISHING

E

THREADING

Connection Accessories

Admissible Tightening Torque* 27.0 in-lbs (305 N-cm)

Insert Screws

Nylon Locking Screws

Insert Driver

Replacement Tips

Preset Torque Hand Driver

739-IP9-1

739N-IP9-1

8IP-9

8IP-9TL

8IP-9B

X

*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength

SPECIALS

Refer to Speed and Feed charts for recommended adjustments to speeds and feeds. Refer to page A20: 86 for deep hole drilling guidelines in this section of the catalog. Visit www.alliedmachine.com/DeepHoleGuidelines for the most up-to-date information and procedures. Factory technical assistance is available for your specific applications through our Application Engineering Team. ext: 7611 | email: appeng@alliedmachine.com WARNING

Screws sold in multiples of 10 = Imperial (in) = Metric (mm)

www.alliedmachine.com | 1.330.343.4283

A20: 53