A20-XTP_EU-EN

13

DRILLING | GEN3SYS® XT Pro and XT High Penetration Replaceable Insert Drilling System

GEN3SYS XT Pro Drill Insert Holders 13 Series | Diameter Range: 13.00 mm - 13.99 mm (0.5118" - 0.5511")

A

L 1

L 7

L 4

DRILLING

D 2

L 2

L 3

B

Body

Shank

L 2

L 4

L 3

L 1

L 7

D 2

Flute

Length

Flat YES NO YES NO YES NO YES NO YES NO YES NO YES NO YES NO YES NO YES NO

Part No.

BORING

HXT0313S-20FM HXT0313S-20CM HXT0513S-20FM HXT0513S-20CM HXT0713S-20FM HXT0713S-20CM HXT1013S-20FM HXT1013S-20CM HXT1213S-20FM HXT1213S-20CM HXT0313S-075F HXT0313S-075C HXT0513S-075F HXT0513S-075C HXT0713S-075F HXT0713S-075C HXT1013S-075F HXT1013S-075C HXT1213S-075F HXT1213S-075C

3xD 3xD 5xD 5xD 7xD 7xD

42.0 42.0 69.9 69.9 98.0 98.0

69.0 69.0 96.8 96.8

71.4 71.4 99.2 99.2

119.0 119.0 146.8 146.8 175.0 175.0 217.0 217.0 245.2 245.2 4-3/4 4-3/4

50.0 50.0 50.0 50.0 50.0 50.0 50.0 50.0 50.0 50.0

20.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0

Straight

125.0 125.0 167.0 167.0 195.2 195.2

127.4 127.4 169.4 169.4 197.4 197.4

10xD 10xD 12xD 12xD

140.0 140.0 168.0 168.0

C

3xD 3xD 5xD 5xD 7xD 7xD

1-21/32 1-21/32

2-23/32 2-23/32 3-13/16 3-13/16 4-59/64 4-59/64 6-37/64 6-37/64 7-11/16 7-11/17

2-13/16 2-13/16 3-29/32 3-29/32 5-1/64 5-1/64 6-43/64 6-43/64 7-25/32 7-25/32

2-1/32 2-1/32 2-1/32 2-1/32 2-1/32 2-1/32 2-1/32 2-1/32 2-1/32 2-1/32

3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4

REAMING

2-3/4 2-3/4

5-27/32 5-27/32 6-61/64 6-61/64 8-39/64 8-39/64 9-23/32 9-23/32

Straight

3-55/64 3-55/64 5-33/64 5-33/64 6-39/64 6-39/64

10xD 10xD 12xD 12xD

D

BURNISHING

E

THREADING

Connection Accessories

Admissible Tightening Torque* 84 N-cm (7.4 in-lbs)

Insert Screws

Nylon Locking Screws

Insert Driver

Replacement Tips

Preset Torque Hand Driver

7247-IP7-1

8IP-7

8IP-7TL

8IP-7B

7247N-IP7-1

X

*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength

SPECIALS

Refer to Speed and Feed charts for recommended adjustments to speeds and feeds. Refer to page A20: 86 for deep hole drilling guidelines in this section of the catalogue. Visit www.alliedmachine.com/DeepHoleGuidelines for the most up-to-date information and procedures. Factory technical assistance is available for your specific applications through our Application Engineering Team. email: engineering.eu@alliedmachine.com WARNING

Screws sold in multiples of 10 = Metric (mm) = Imperial (in)

www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com

A20: 21