A20-XTP_EU-EN

14

DRILLING | GEN3SYS® XT Pro and XT High Penetration Replaceable Insert Drilling System

GEN3SYS XT Pro Drill Insert Holders 14 Series | Diameter Range: 14.00 mm - 14.99 mm (0.5512" - 0.5905")

A

L 1

DRILLING

L 7

L 4

D 2

L 2

L 3

B

Body

Shank

L 2

L 4

L 3

L 1

L 7

D 2

Flute

Length

Flat YES NO YES NO YES NO YES NO YES NO YES NO YES NO YES NO YES NO YES NO

Part No.

BORING

HXT0314S-20FM HXT0314S-20CM HXT0514S-20FM HXT0514S-20CM HXT0714S-20FM HXT0714S-20CM HXT1014S-20FM HXT1014S-20CM HXT1214S-20FM HXT1214S-20CM HXT0314S-075F HXT0314S-075C HXT0514S-075F HXT0514S-075C HXT0714S-075F HXT0714S-075C HXT1014S-075F HXT1014S-075C HXT1214S-075F HXT1214S-075C

3xD 3xD 5xD 5xD 7xD 7xD

44.8 44.8 75.0 75.0

72.2 72.2

74.9 74.9

122.2 122.2 152.4 152.4 182.2 182.2 227.4 227.4 257.2 257.2 4-7/8 4-7/8

50.0 50.0 50.0 50.0 50.0 50.0 50.0 50.0 50.0 50.0

20.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0

102.4 102.4 132.2 132.2 177.4 177.4 207.2 207.2

104.9 104.9 134.8 134.8 179.8 179.8 209.8 209.8

Straight

104.8 104.8 149.9 149.9 180.0 180.0

10xD 10xD 12xD 12xD

C

3xD 3xD 5xD 5xD 7xD 7xD

1-49/64 1-49/64 2-61/64 2-61/64

2-27/32 2-27/32 4-1/32 4-1/32 5-13/64 5-13/64 6-63/64 6-63/64 8-5/32 8-5/32

2-61/64 2-61/64

2-1/32 2-1/32 2-1/32 2-1/32 2-1/32 2-1/32 2-1/32 2-1/32 2-1/32 2-1/32

3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4

REAMING

4-1/8 4-1/8

6-1/16 6-1/16 7-15/64 7-15/64 9-1/64 9-1/64 10-3/16 10-3/16

Straight

4-1/8 4-1/8

5-5/16 5-5/16 7-5/64 7-5/64

10xD 10xD 12xD 12xD

5-29/32 5-29/32 7-3/32 7-3/32

8-1/4 8-1/4

D

BURNISHING

E

THREADING

Connection Accessories

Admissible Tightening Torque* 84 N-cm (7.4 in-lbs)

Insert Screws

Nylon Locking Screws

Insert Driver

Replacement Tips

Preset Torque Hand Driver

7247-IP7-1

7247N-IP7-1

8IP-7

8IP-7TL

8IP-7B

X

*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength

SPECIALS

Refer to Speed and Feed charts for recommended adjustments to speeds and feeds. Refer to page A20: 86 for deep hole drilling guidelines in this section of the catalogue. Visit www.alliedmachine.com/DeepHoleGuidelines for the most up-to-date information and procedures. Factory technical assistance is available for your specific applications through our Application Engineering Team. email: engineering.eu@alliedmachine.com WARNING

Screws sold in multiples of 10 = Metric (mm) = Imperial (in)

www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com

A20: 25

Made with FlippingBook Digital Publishing Software