A20-XTP_EU-EN

18

DRILLING | GEN3SYS® XT Pro and XT High Penetration Replaceable Insert Drilling System

GEN3SYS XT Pro Drill Insert Holders 18 Series | Diameter Range: 18.00 mm - 19.99 mm (0.7087" - 0.7873")

A

L 1

DRILLING

L 7

L 4

D 2

L 2

L 3

B

Body

Shank

L 2

L 4

L 3

L 1

L 7

D 2

Flute

Length

Flat YES NO YES NO YES NO YES NO YES NO YES NO YES NO YES NO YES NO YES NO

Part No.

BORING

HXT0318S-25FM HXT0318S-25CM HXT0518S-25FM HXT0518S-25CM HXT0718S-25FM HXT0718S-25CM HXT1018S-25FM HXT1018S-25CM HXT1218S-25FM HXT1218S-25CM HXT0318S-100F HXT0318S-100C HXT0518S-100F HXT0518S-100C HXT0718S-100F HXT0718S-100C HXT1018S-100F HXT1018S-100C HXT1218S-100F HXT1218S-100C

3xD 3xD 5xD 5xD 7xD 7xD

60.0 60.0

94.0 94.0

96.8 96.8

150.0 150.0 189.7 189.7 229.4 229.4 290.1 290.1 329.9 329.9

56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0

25.0 25.0 25.0 25.0 25.0 25.0 25.0 25.0 25.0 25.0

100.0 100.0 140.0 140.0 199.9 199.9 240.0 240.0

133.7 133.7 173.4 173.4 234.1 234.1 273.9 273.9

136.8 136.8 176.8 176.8 236.7 236.7 276.7 276.7

Straight

10xD 10xD 12xD 12xD

C

3xD 3xD 5xD 5xD 7xD 7xD

2-23/64 2-23/64 3-15/16 3-15/16 5-33/64 5-33/64

3-45/64 3-45/64 5-17/64 5-17/64 6-27/32 6-27/32 9-7/32 9-7/32

3-13/16 3-13/16 5-25/64 5-25/64 6-61/64 6-61/64 9-5/16 9-5/16

5-63/64 5-63/64 7-35/64 7-35/64

2-9/32 2-9/32 2-9/32 2-9/32 2-9/32 2-9/32 2-9/32 2-9/32 2-9/32 2-9/32

1 1 1 1 1 1 1 1 1 1

REAMING

Straight

9-1/8 9-1/8

10xD 10xD 12xD 12xD

7-7/8 7-7/8

11-31/64 11-31/64

9-7/16 9-7/16

10-25/32 10-57/64 13-1/16 10-25-32 10-57/64 13-1/16

D

BURNISHING

E

THREADING

Connection Accessories

Admissible Tightening Torque* 305 N-cm (27.0 in-lbs)

Insert Screws

Nylon Locking Screws

Insert Driver

Replacement Tips

Preset Torque Hand Driver

7375-IP9-1

7375N-IP9-1

8IP-9

8IP-9TL

8IP-9B

X

*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength

SPECIALS

Refer to Speed and Feed charts for recommended adjustments to speeds and feeds. Refer to page A20: 86 for deep hole drilling guidelines in this section of the catalogue. Visit www.alliedmachine.com/DeepHoleGuidelines for the most up-to-date information and procedures. Factory technical assistance is available for your specific applications through our Application Engineering Team. email: engineering.eu@alliedmachine.com WARNING

Screws sold in multiples of 10 = Metric (mm) = Imperial (in)

www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com

A20: 41