A20-XTP_EU-EN

26

DRILLING | GEN3SYS® XT Pro and XT High Penetration Replaceable Insert Drilling System

GEN3SYS XT Pro Drill Insert Holders

26 Series | Diameter Range: 26.00 mm - 28.99 mm (1.0236" - 1.1416")

A

L 1

DRILLING

L 7

L 4

D 2

L 2

L 3

B

Body

Shank

L 2

L 4

L 3

L 1

L 7

D 2

Flute

Length

Flat YES NO YES NO YES NO YES NO YES NO YES NO YES NO YES NO YES NO YES NO

Part No.

BORING

HXT0326S-32FM HXT0326S-32CM HXT0526S-32FM HXT0526S-32CM HXT0726S-32FM HXT0726S-32CM HXT1026S-32FM HXT1026S-32CM HXT1226S-32FM HXT1226S-32CM HXT0326S-125F HXT0326S-125C HXT0526S-125F HXT0526S-125C HXT0726S-125F HXT0726S-125C HXT1026S-125F HXT1026S-125C HXT1226S-125F HXT1226S-125C

3xD 3xD 5xD 5xD 7xD 7xD

87.0 87.0

128.6 128.6 186.5 186.5 244.5 244.5 331.4 331.4 389.0 389.0

131.4 131.4 189.4 189.4 247.4 247.4 334.4 334.4 391.8 391.8

188.6 188.6 246.5 246.5 304.5 304.5 391.4 391.4 449.0 449.0

60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0

32.0 32.0 32.0 32.0 32.0 32.0 32.0 32.0 32.0 32.0

145.0 145.0 202.9 202.9 289.9 289.9 348.0 348.0

Straight

10xD 10xD 12xD 12xD

C

3xD 3xD 5xD 5xD 7xD 7xD

3-27/64 3-27/64 5-45/64 5-45/64 7-63/64 7-63/64

5-1/16 5-1/16 7-11/32 7-11/32

5-11/64 5-11/64 7-29/64 7-29/64

7-11/32 7-11/32

2-9/32 2-9/32 2-9/32 2-9/32 2-9/32 2-9/32 2-9/32 2-9/32 2-9/32 2-9/32

1-1/4 1-1/4 1-1/4 1-1/4 1-1/4 1-1/4 1-1/4 1-1/4 1-1/4 1-1/4

REAMING

9-5/8 9-5/8

Straight

9-5/8 9-5/8

9-47/64 11-29/32 9-47/64 11-29/32

10xD 11-13/32 13-3/64 13-11/64 15-21/64 10xD 11-13/32 13-3/64 13-11/64 15-21/64

12xD 13-45/64 15-11/32 15-29/64 12xD 13-45/64 15-11/32 15-29/64

17-5/8 17-5/8

D

BURNISHING

E

THREADING

Connection Accessories

Admissible Tightening Torque* 690 N-cm (61.0 in-lbs)

Insert Screws 7495-IP15-1

Nylon Locking Screws

Insert Driver

Replacement Tips

Preset Torque Hand Driver

7495N-IP15-1

8IP-15

8IP-15TL

8IP-15B

X

*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength

SPECIALS

Refer to Speed and Feed charts for recommended adjustments to speeds and feeds. Refer to page A20: 86 for deep hole drilling guidelines in this section of the catalogue. Visit www.alliedmachine.com/DeepHoleGuidelines for the most up-to-date information and procedures. Factory technical assistance is available for your specific applications through our Application Engineering Team. email: engineering.eu@alliedmachine.com WARNING

Screws sold in multiples of 10 = Metric (mm) = Imperial (in)

www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com

A20: 57