A91-SSD_ESM

22

DRILLING | Structural Steel Solutions | GEN3SYS® XT Pro Replaceable Insert Drills

GEN3SYS® XT Pro Structural Steel Drilling System 22 Series | Diameter Range: 0.8661" - 0.9448" (22.00 mm - 23.99 mm)

A

D 1

DRILLING

140°

Inserts

B

Insert

D 1 inch 0.8661 0.8752 0.9055 0.9374

D 1 mm

Fractional Equivalent

XTST Part No. XTST22-22.00 XTST22-22.23 XTST22-23.00 XTST22-23.81

BORING

-

22.00 22.23 23.00 23.81

7/8

-

15/16

L 1

L 7

L 4

C

D 2

REAMING

L 2

P 1

L 3

Holders

Body

Shank

L 2

L 4

L 3

L 1

L 7

D 2

P 1

Length

Flat YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES

Part No.

ST01220-100F ST01225-100F ST03220-100F ST03225-100F* ST05220-100F ST05225-100F* ST07220-100F ST07225-100F* ST01220-25FM ST01225-25FM ST03220-25FM ST03225-25FM* ST05220-25FM ST05225-25FM* ST07220-25FM ST07225-25FM*

1.5xD 1.5xD

1.406 1.406 2.828 2.828 4.719 4.719 6.609 6.609

2.719 2.719 4.141 4.141 6.031 6.031 7.922 7.922 105.3 105.3 153.3 153.3 201.3 201.3 69.3 69.3

2.859 2.859 4.281 4.281 6.172 6.172 8.063 8.063 108.7 108.7 156.7 156.7 204.7 204.7 72.7 72.7

5.000 5.000 6.422 6.422 8.313 8.313 125.3 125.3 161.3 161.3 209.3 209.3 257.3 257.3 10.203 10.203

2.281 2.281 2.281 2.281 2.281 2.281 2.281 2.281

1 1 1 1 1 1 1 1

1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/8 BSPT 1/8 BSPT 1/8 BSPT 1/8 BSPT 1/8 BSPT 1/8 BSPT 1/8 BSPT 1/8 BSPT

D

3xD 3xD 5xD 5xD 7xD 7xD 3xD 3xD 5xD 5xD 7xD 7xD

BURNISHING

1.5xD 1.5xD

36.0 36.0 72.0 72.0

56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0

25 25 25 25 25 25 25 25

119.9 119.9 167.9 167.9

E

THREADING

*Oversized body holder (minimum drill diameter = 23 mm) Connection Accessories

Admissible Tightening Torque* 27.0 in-lbs (305 N-cm)

Insert Screws

Nylon Locking Screws

Insert Driver

Replacement Tips

Preset Torque Hand Driver

739-IP9-1

739N-IP9-1

8IP-9

8IP-9TL

8IP-9B

*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength.

X

A91: 64 - 65

A91: 23

Key on A91: 1

Inserts sold in multiples of 1. | Screws sold in multiples of 10. = Imperial (in) = Metric (mm)

SPECIALS

NOTICE: Structural steel GEN3SYS holders are specifically designed to be used only with GEN3SYS XT Pro structural steel geometry inserts. Using other GEN3SYS XT or XT Pro insert geometries in these holders could lead to chip packing and tool failure. Contact Application Engineering for questions regarding proper use of tools. ext: 7611 | email: appeng@alliedmachine.com

A91: 32

www.alliedmachine.com | 1.330.343.4283