A15-SUP_US-EN

DRILLING |

: Solid Carbide Drilling SoluƟons ®

Recommended Drilling Data | Imperial (inch)

A

Feed Rate (IPR) by Diameter

DRILLING

Hardness (BHN) 100 - 150 150 - 200 200 - 250 85 - 125 125 - 175 175 - 225 225 - 275 125 - 175 175 - 225 225 - 275 275 - 325 125-175 175-225 225-275 275-325 325-375 225 - 300 300 - 350 350 - 400 100 - 150 150 - 250 250 - 350 150 - 200 200 -250 140-220 220-310 140-220 220-310 185-275 275-350

General Application Geometry

Speed (SFM)

ISO Material

Special Geometry*

Coating AM420 AM420 AM420 AM420 AM420 AM420 AM420 AM420 AM420 AM420 AM420 AM420 AM420 AM420 AM420 AM420 AM420 AM420 AM420 AM420 AM420 AM420 AM420 AM420 AM460 AM460 AM460 AM460 AM460 AM460

0.118 - 0.157 0.157 - 0.197

Free Machining Steel 1118, 1215, 12L14, etc.

HPM HPM

HPM2M HPM2M HPS2M HPM2M HPM2M HPM2M HPS2M HPM2M HPM2M HPS2M HPS2M HPM2M HPM2M HPS2M HPS2M

500 475 450 455 440 425 410 440 430 400 375 405 380 365 340 325 340 320 250 450 425 390 270 250 110 100 150 120 160 130

0.006 0.005 0.004 0.006 0.006 0.005

0.007

0.0065

HPS

0.006 0.007

Low Carbon Steel 1010, 1020, 1025, 1522, 1144, etc.

HPM HPM HPM

0.0065 0.006 0.006 0.006 0.005 0.005 0.006 0.0055 0.0055

B

HPS

0.0045 0.0055

Medium Carbon Steel 1030, 1040, 1050, 1527,

HPM HPM

0.005

BORING

1151, etc.

HPS HPS

0.0045

0.004

Alloy Steel

HPM HPM

0.0055

P

4140, 5140, 8640, etc.

0.005 0.004 0.004

HPS HPS

0.005 0.005

HP106

-

0.0035

0.0045

High Strength Alloy

HPS HPS

HPS2M HPS2M

0.004 0.004

0.005 0.005 0.004

4340, 4330V, 300M, etc.

C

HP106

-

0.0035 0.0055 0.0045

Structural Steel

HPS HPS HPS

HPS2M HPS2M HPS2M HPM2M HPS2M

0.0065 0.0055

A36, A285, A516, etc.

REAMING

0.004

0.005

Tool Steel

HPM

0.0045

0.0045

H-13, H-21, A-4, 0-2, S-3, etc.

HPS

0.004

0.004

High Temp Alloy

HPS HPS HPS HPS HPS HPS

- - - - - -

0.003 0.002

0.003 0.002 0.003

Hastelloy B, Inconel 600, etc.

Titanium Alloy

0.0025

S

0.002 0.003 0.002

0.0025

Aerospace Alloy

0.003 0.002

D

S82

BURNISHING

*Special Geometry Use HPM2M for greater drill depths over 8xD. HPM2M is used for any interrupƟons and produces a beƩer hole tolerance and finish in comparison to HPM.

Use HPS2M for greater drill depths over 8xD. HPS2M is used for any interrupƟons and produces a beƩer hole tolerance and finish in comparison to HPS.

E

Flood Coolant Applications Recommend if diameter to depth is less than or equal to three Ɵmes the diameter. Reduce speed by 20% and if needed drop feed by 10% to maintain opƟmal chip formaƟon

THREADING

Parameter Reductions for Length to Diameter Relationships 6xD

Parameter Recommendations for Step Drills • Feed rate is based off the pilot diameter • Speed rate is based off the largest step diameter

0.90 reducƟon for speed and feed adjustment 0.80 reducƟon for speed and feed adjustment 0.70 reducƟon for speed and feed adjustment 0.60 reducƟon for speed and feed adjustment

9xD

12xD

15xD - 20xD

X

SPECIALS Refer to Speed and Feed charts for recommended adjustments to speeds and feeds. Refer to page A15: 17 for deep hole drilling guidelines in this secƟon of the catalog. Visit www.alliedmachine.com/DeepHoleGuidelines for the most up-to-date informaƟon and procedures. Factory technical assistance is available for your specific applicaƟons through our ApplicaƟon Engineering Team. ext: 7611 | email: appeng@alliedmachine.com WARNING

IMPORTANT: The speeds and feeds listed above are a general starƟng point for all applicaƟons. Refer to the Coolant RecommendaƟon charts for coolant requirements to run at the recommended speeds and feeds. Factory technical assistance is also available through our ApplicaƟon Engineering Team. ext: 7611 | email: appeng@alliedmachine.com

A15: 8

www.alliedmachine.com