A30-TAS_US-EN

DRILLING | T-A® Replaceable Insert Drilling System

A

M/min

Feed Rate (mm/rev) by Diameter

DRILLING

Hardness (BHN)

Carbide Grade TiN TiAlN TiCN

9.50 mm - 12.95 mm

12.98 mm - 17.52 mm

17.53 mm - 24.38 mm

24.41 mm - 35.00 mm

35.01 mm - 47.80 mm

ISO Material

Wear Plate

400 500 600

C5 C5 C5

23 15 11 34 20 98 82 73 64 55

35 26 22 43 25

30 21 16 39 23

0.07 0.05 0.04

0.12 0.10 0.08 0.18 0.15 0.30 0.28 0.23 0.20 0.18 0.38 0.33 0.15 0.28 0.20 0.15 0.23 0.08

0.20 0.15 0.12 0.23 0.20 0.38 0.33 0.30 0.28 0.25 0.45 0.40 0.25 0.36 0.25 0.18 0.28 0.10

0.25 0.20 0.16 0.28 0.23 0.48 0.43 0.38 0.33 0.28 0.50 0.45 0.30 0.45 0.36 0.25 0.38 0.15

0.30 0.25 0.20 0.33 0.28 0.58 0.53 0.45 0.38 0.33 0.55 0.50 0.36 0.50 0.42 0.33 0.45 0.25

Hardox®, AR400, T-1, etc.

H

Hardened Steel

300 - 400 C5 400 - 500 C5 120 - 150 C2, C3 150 - 200 C2, C3 200 - 220 C2, C3 220 - 260 C2, C3 260 - 320 C2, C3

0.10 0.08

B

Nodular, Grey, Ductile Cast Iron

141 122 110

127 102

0.20 0.18 0.15 0.13 0.13 0.25 0.23 0.10 0.20 0.13 0.10 0.15

K

BORING

93 79 69

95 83

Cast Aluminum

30

C2 C2 C2 C2

366 244 366 244

460 306 460 306 110

410 275 410 275 100

180

Wrought Aluminum

30

180

N

Aluminum Bronze

100 - 200 C2 200 - 250 C2

85 64

C

94

79

Brass

100

C2 C2

130

184 120

160 100

Copper

60

80

0.05

REAMING

Contact our Application Engineering department for assistance when machining these materials

Deep Hole Drilling Speed and Feed Adjustment Holder Length

Recommended Speed and Feed Example If the recommended speed and feed is 50 M/min and 0.20 mm/rev for a standard length holder, then the speed and feed using a 3XL holder in the same application would be 37.5 M/min and 0.18 mm/rev.

Extended Long

Long Plus

XL

3XL

Speed

0.90

0.85 0.95

0.80 0.90

0.80 0.90

0.75 0.90

D

50 • 0.75 = 37.5 M/min

0.20 • 0.90 = 0.18 mm/rev

Feed

-

BURNISHING

Formulas 1. RPM = (318.47 • M/min) / DIA

2. mm/min = RPM • mm/rev

3. M/min = RPM • 0.003 • DIA

where:

where:

where:

RPM

= revolutions per minute (rev/min)

mm/min = mm per minute (mm/min)

M/min = speed (M/min)

M/min = speed (M/min)

RPM

= revolutions per minute (rev/min)

RPM

= revolutions per minute (rev/min)

DIA

= diameter of drill (mm)

mm/rev = feed rate (mm/rev)

DIA

= diameter of drill (mm)

E

THREADING

X

Tool failure can cause serious injury. To prevent: - When using holders without support bushing, use a short T-A® holder to establish an initial hole that is a minimum of 2 diameters deep. - Do not rotate tool holder more than 50 RPM unless it is engaged with the workpiece or fixture. Visit www.alliedmachine.com/DeepHoleGuidelines for the most up-to-date information and procedures. Factory technical assistance is available for your specific applications through our Application Engineering Team. WARNING

SPECIALS

www.alliedmachine.com | 1.330.343.4283

A30: 135