A30-TAS_US-EN
1
DRILLING | T-A® Replaceable Insert Drilling System
T-A® Drill Insert Holders 1 Series | Flange Shank | Diameter Range: 0.690" - 0.960" (17.53 mm - 24.38 mm)
A
L 1
DRILLING
L 7
L 4
D 2
L 2
P 1
B
L 3
L 1
BORING
L 7
L 4
D 2
C
P 1
P 2
L 2
Stub Length
L 3
Straight Flute
REAMING
Body
Shank
Series
Length
Part No.
L 2
L 4
L 3
L 1
D 2
L 7
P 1
21010S-100F 22010S-100F 23010S-100F 24010S-100F 25010S-100F 21015S-100F 22015S-100F 23015S-100F 24015S-100F 25015S-100F 21010S-25FM 22010S-25FM 27010S-25FM 29010S-25FM 21015S-25FM 22015S-25FM
Stub Short
1-7/8 2-5/8 4-5/8 6-5/8 2-1/4 2-5/8 4-5/8 6-5/8 10-5/8 10-5/8
2-63/64 4-7/32 6-3/32 8-3/32 12-3/32 3-31/64 4-7/32 6-3/32 8-3/32 12-3/32
3-1/8
5-17/64
1 1 1 1 1 1 1 1 1 1
2-9/32 2-9/32 2-9/32 2-9/32 2-9/32 2-9/32 2-9/32 2-9/32 2-9/32 2-9/32
1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8
4-23/64 6-15/64 8-15/64 12-15/64 4-23/64 6-15/64 8-15/64 12-15/64 3-5/8
6-1/2 8-3/8
1
Intermediate
Standard Extended
10-3/8 14-3/8 5-49/64
D
Stub Short
6-1/2 8-3/8
1.5 BURNISHING
Intermediate
Standard Extended
10-3/8 14-3/8 131.8 163.2 550.5 658.5 144.5 163.2
Stub Short
47.6 66.7
75.8
79.4
25.0 25.0 25.0 25.0 25.0 25.0
56.0 56.0 56.0 56.0 56.0 56.0
1/8* 1/8* 1/8* 1/8* 1/8* 1/8*
107.2 494.5 602.5
110.7 498.1 606.1
1
XL
457.0 569.0
3XL
Stub Short
57.2 66.7
88.5
92.1
1.5
107.2
110.7
E
*Metric thread to BSP and ISO 7-1 NOTE: Stub length holders have a 1/8" side pipe tap ( P 2 ) NOTE: 1.5 series inserts fit into both 1 and 1.5 series holders. However, 1 series inserts ONLY fit into 1 series holders. See page A30: 7 for visual.
THREADING
Connection Accessories
Admissible Tightening Torque* 27.0 in-lbs (305 N-cm) 27.0 in-lbs (305 N-cm)
Series
Insert Screws
Nylon Locking Screws
Insert Driver
Replacement Tips
Preset Torque Hand Driver
1
7375-IP9-1 739-IP9-1
7375N-IP9-1 739N-IP9-1
8IP-9 8IP-9
8IP-9TL 8IP-9TL
8IP-9B 8IP-9B
1.5
*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength
A30: 44 - 51
A30: 57 & 111
X
Key on A30: 1
= Imperial (in) = Metric (mm) Screws sold in quantities of 10
SPECIALS
Refer to Speed and Feed charts for recommended adjustments to speeds and feeds. Refer to page A30: 146 for deep hole drilling guidelines in this section of the catalog. Visit www.alliedmachine.com/DeepHoleGuidelines for the most up-to-date information and procedures. Factory technical assistance is available for your specific applications through our Application Engineering Team. WARNING
A30: 52
www.alliedmachine.com | 1.330.343.4283
Made with FlippingBook - professional solution for displaying marketing and sales documents online