A25-TAP_EU-EN

1

DRILLING | T-A Pro® High Penetration Replaceable Insert Drilling System

T-A Pro Drill Holders 1 Series Metric | Diameter Range: 17.65 mm - 24.37 mm

A

L 1

L 7

L 4

DRILLING

D 2

L 2

L 3

Body

Shank

B

Length Sub Series

L 2

L 4

L 3

L 1

L 7

D 2 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25

Flat Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No

Part No

HTA1A10-25FM HTA1A10-25CM HTA1B10-25FM HTA1B10-25CM HTA1C10-25FM HTA1C10-25CM HTA1D10-25FM HTA1D10-25CM HTA1A12-25FM HTA1A12-25CM HTA1B12-25FM HTA1B12-25CM HTA1C12-25FM HTA1C12-25CM HTA1D12-25FM HTA1D12-25CM HTA1A15-25FM HTA1A15-25CM HTA1B15-25FM HTA1B15-25CM HTA1C15-25FM HTA1C15-25CM HTA1D15-25FM HTA1D15-25CM

10xD 10xD 10xD 10xD 10xD 10xD 10xD 10xD 12xD 12xD 12xD 12xD 12xD 12xD 12xD 12xD 15xD 15xD 15xD 15xD 15xD 15xD 15xD 15xD

A A B B C C D D A A B B C C D D A A B B C C D D

209.6 209.6 209.6 209.6 209.6 209.6 209.6 209.6 251.5 251.5 251.5 251.5 251.5 251.5 251.5 251.5 314.3 314.3 314.3 314.3 314.3 314.3 314.3 314.3

247.6 247.6 247.6 247.6 247.6 247.6 247.6 247.6 289.5 289.5 289.5 289.5 289.5 289.5 289.5 289.5 352.4 352.4 352.4 352.4 352.4 352.4 352.4 352.4

251.2 251.2 251.2 251.2 251.2 251.2 251.2 251.2 293.1 293.1 293.1 293.1 293.1 293.1 293.1 293.1 355.9 355.9 355.9 355.9 355.9 355.9 355.9 355.9

305.5 305.5 305.5 305.5 305.5 305.5 305.5 305.5 347.4 347.4 347.4 347.4 347.4 347.4 347.4 347.4 410.3 410.3 410.3 410.3 410.3 410.3 410.3 410.3

56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0

BORING

C

REAMING

D

BURNISHING

E

THREADING

Connection Accessories

Admissible Tightening Torque* 305 N-cm (27.0 in-lbs ) 305 N-cm (27.0 in-lbs )

Insert Screws

Nylon Locking Screws

Insert Driver

Replacement Tips

Preset Torque Hand Driver

A/B C/D

7375-IP9-1 739-IP9-1

7375N-IP9-1 739N-IP9-1

8IP-9 8IP-9

8IP-9TL 8IP-9TL

8IP-9B 8IP-9B

*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength

Refer to Speed and Feed charts for recommended adjustments to speeds and feeds. Refer to page A25: 68 for deep hole drilling guidelines in this section of the catalogue. Visit www.alliedmachine.com/DeepHoleGuidelines for the most up-to-date information and procedures. Factory technical assistance is available for your specific applications through our Application Engineering department. emai l : engineering.eu@alliedmachine.com WARNING

X

A25: 58 - 65

A25: 22 - 25

A25: 26 - 29

SPECIALS

Key on A25: 1

Screws sold in multiples of 10 = Metric (mm) = Imperial (in)

www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com

A25: 31