A25-TAP_EU-EN

2

DRILLING | T-A Pro® High Penetration Replaceable Insert Drilling System

T-A Pro Drill Holders

2 Series Metric | Diameter Range: 24.38 mm - 35.04 mm

A

L 1

L 7

L 4

DRILLING

D 2

L 2

L 3

Body

Shank

B

Length Sub Series

L 2

L 4

L 3

L 1

L 7

D 2 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32

Flat Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No

Part No

HTA2A10-32FM HTA2A10-32CM HTA2B10-32FM HTA2B10-32CM HTA2C10-32FM HTA2C10-32CM HTA2D10-32FM HTA2D10-32CM HTA2A12-32FM HTA2A12-32CM HTA2B12-32FM HTA2B12-32CM HTA2C12-32FM HTA2C12-32CM HTA2D12-32FM HTA2D12-32CM HTA2A15-32FM HTA2A15-32CM HTA2B15-32FM HTA2B15-32CM HTA2C15-32FM HTA2C15-32CM HTA2D15-32FM HTA2D15-32CM

10xD 10xD 10xD 10xD 10xD 10xD 10xD 10xD 12xD 12xD 12xD 12xD 12xD 12xD 12xD 12xD 15xD 15xD 15xD 15xD 15xD 15xD 15xD 15xD

A A B B C C D D A A B B C C D D A A B B C C D D

297.4 297.4 297.4 297.4 297.4 297.4 297.4 297.4 356.9 356.9 356.9 356.9 356.9 356.9 356.9 356.9 446.2 446.2 446.2 446.2 446.2 446.2 446.2 446.2

345.6 345.6 345.6 345.6 345.6 345.6 345.6 345.6 405.1 405.1 405.1 405.1 405.1 405.1 405.1 405.1 494.4 494.4 494.4 494.4 494.4 494.4 494.4 494.4

349.2 349.2 349.2 349.2 349.2 349.2 349.2 349.2 408.7 408.7 408.7 408.7 408.7 408.7 408.7 408.7 497.9 497.9 497.9 497.9 497.9 497.9 497.9 497.9

403.6 403.6 403.6 403.6 403.6 403.6 403.6 403.6 463.0 463.0 463.0 463.0 463.0 463.0 463.0 463.0 552.3 552.3 552.3 552.3 552.3 552.3 552.3 552.3

60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0

BORING

C

REAMING

D

BURNISHING

E

THREADING

Connection Accessories

Admissible Tightening Torque* 690 N-cm (61.0 in-lbs)

Insert Screws 7495-IP15-1

Nylon Locking Screws

Insert Driver

Replacement Tips

Preset Torque Hand Driver

7495N-IP15-1

8IP-15

8IP-15TL

8IP-15B

*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength

Refer to Speed and Feed charts for recommended adjustments to speeds and feeds. Refer to page A25: 68 for deep hole drilling guidelines in this section of the catalogue. Visit www.alliedmachine.com/DeepHoleGuidelines for the most up-to-date information and procedures. Factory technical assistance is available for your specific applications through our Application Engineering department. emai l : engineering.eu@alliedmachine.com WARNING

X

A25: 58 - 65

A25: 34 - 37

A25: 38 - 41

SPECIALS

Key on A25: 1

Screws sold in multiples of 10 = Metric (mm) = Imperial (in)

www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com

A25: 43