A30-TAS_EU-EN
DRILLING | T-A® Replaceable Insert Drilling System
Deep Hole Drilling Speed and Feed Adjustment Holder Length
A
Feed Rate (mm/rev) by Diameter
DW Cuƫng Data
DRILLING
17.53 - 24.38
24.41 - 35.00
35.01 - 47.80
47.85 - 65.99
66.00 - 114.48
Speed m/min
Feed (mm/rev)
Extended Long Long Plus
XL
3XL
Speed
0.90
0.85 0.95
0.80 0.90
0.80 0.90
0.75 0.90
0.33 0.33 0.33 0.30 0.30 0.25 0.25 0.30 0.25 0.25 0.23 0.25 0.25 0.25 0.23 0.23 0.23 0.23 0.20 0.30 0.25 0.23 0.20 0.20 0.20 0.18 0.20 0.18 0.23 0.20 0.23 0.20 0.20 0.18 0.20 0.18 0.20 0.18 0.20 0.18 0.41 0.36 0.30 0.23 0.18 0.41 0.41 0.25 0.41 0.36 0.23 0.41 0.15 -
0.41 0.41 0.41 0.38 0.38 0.36 0.36 0.38 0.36 0.36 0.30 0.36 0.36 0.36 0.30 0.30 0.25 0.25 0.23 0.36 0.30 0.25 0.25 0.25 0.25 0.20 0.25 0.20 0.25 0.20 0.25 0.20 0.25 0.20 0.25 0.20 0.23 0.20 0.23 0.20 0.51 0.46 0.41 0.30 0.23 0.51 0.46 0.30 0.46 0.46 0.30 0.51 0.20 -
0.51 0.51 0.51 0.48 0.48 0.46 0.46 0.48 0.46 0.46 0.41 0.43 0.43 0.43 0.38 0.38 0.36 0.36 0.30 0.46 0.41 0.36 0.30 0.30 0.30 0.25 0.30 0.25 0.36 0.30 0.36 0.30 0.36 0.30 0.36 0.30 0.30 0.25 0.30 0.25 0.61 0.56 0.46 0.36 0.30 0.56 0.56 0.56 0.56 0.56 0.36 0.61 0.30 -
0.58 0.58 0.58 0.58 0.58 0.53 0.53 0.58 0.53 0.53 0.48 0.48 0.48 0.48 0.43 0.43 0.43 0.43 0.38 0.53 0.48 0.43 0.38 0.38 0.38 0.30 0.38 0.30 0.41 0.36 0.41 0.36 0.41 0.36 0.41 0.36 0.41 0.30 0.41 0.30 0.69 0.64 0.53 0.43 0.36 0.64 0.64 0.64 0.64 0.66 0.43 0.71 0.36 -
0.71 0.71 0.71 0.69 0.69 0.61 0.61 0.69 0.61 0.61 0.56 0.56 0.56 0.56 0.51 0.51 0.51 0.51 0.46 0.66 0.61 0.51 0.43 0.43 0.51 0.46 0.51 0.46 0.51 0.46 0.51 0.46 0.46 0.41 0.46 0.41 0.76 0.71 0.61 0.51 0.41 0.64 0.64 0.64 0.64 0.71 0.51 0.76 0.41 - - - - -
Feed
-
58-76
0.35
Recommended Speed and Feed Example If the recommended speed and feed is 50 m/min and 0.20 mm/ rev for a standard length holder, then the speed and feed using a 3XL holder in the same applicaƟon would be 37.5 m/min and 0.18 mm/rev. 50 • 0.75 = 37.5 m/min 0.20 • 0.90 = 0.18 mm/rev
48-66
0.30
B
48-66
0.30
BORING
30.36
0.28
Formulas 1. RPM = (318.47 • m/min) / DIA where: RPM
22-26
0.25
= revoluƟons per minute (rev/min)
m/min
= speed (m/min)
16-20
0.25
DIA
= diameter of drill (mm)
C
42-54
0.30
2. mm/min = RPM • mm/rev where: mm/min
= mm per minute (mm/min)
31-38
0.23
REAMING
RPM
= revoluƟons per minute (rev/min)
mm/rev
= feed rate (mm/rev)
3. m/min
= RPM • 0.003 • DIA
N/A
N/A
where: m/min
= speed (m/min)
RPM
= revoluƟons per minute (rev/min)
DIA
= diameter of drill (mm)
22-29*
0.23*
D
22-29*
0.23*
BURNISHING
16-20*
0.23*
N/A
N/A
N/A
N/A
53-62
0.30
E
THREADING
109-146
0.32
109-146
0.32
35-44
0.30
79-99 29-32
0.38 0.20
*only applicable up to 120 mm.
X
Tool failure can cause serious injury. To prevent: - When using holders without support bushing, use a short T-A® holder to establish an iniƟal hole that is a minimum of 2 diameters deep. - Do not rotate tool holder more than 50 RPM unless it is engaged with the workpiece or fixture. Visit www.alliedmachine.com/DeepHoleGuidelines for the most up-to-date informaƟon and procedures. Factory technical assistance is available for your specific applicaƟons through our ApplicaƟon Engineering Team. WARNING
SPECIALS
www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com
A30: 117
Made with FlippingBook - Online Brochure Maker