A30-TAS_EU-EN

DRILLING | T-A® Replaceable Insert Drilling System

A

m/min

Feed Rate (mm/rev) by Diameter

DRILLING

Hardness (BHN)

Carbide Grade TiN TiAlN TiCN AM200®

9.50 mm - 12.95 mm

12.98 mm - 17.53 mm

17.54 mm - 24.38 mm

24.41 mm - 35.00 mm

ISO Material

Wear Plate

400 500 600

C2 C2 C2

20 13 10 30 18 82 70 61 55 47

31 23 19 38 22

26 18 14 34 20 87 79 67 58

39 31 25 41 33

0.06 0.04 0.03 0.08 0.06

0.10 0.08 0.06 0.14 0.12 0.26 0.24 0.19 0.17 0.15 0.32 0.28 0.18 0.16 0.16 0.12 0.18 0.06

0.16 0.12 0.10 0.18 0.16 0.32 0.28 0.26 0.24 0.22 0.41 0.35 0.23 0.20 0.20 0.14 0.22 0.08

0.20 0.16 0.13 0.22 0.18 0.41 0.38 0.32 0.28 0.24 0.43 0.39 0.25 0.22 0.29 0.20 0.30 0.12

Hardox®, AR400, T-1, etc.

H

Hardened Steel

300 - 400 C2 400 - 500 C2 120 - 150 C2 150 - 200 C2 200 - 220 C2 220 - 260 C2 260 - 320 C2

Nodular, Grey, Ductile Cast Iron

120 104

108

137 119 108

0.17 0.15 0.13 0.11 0.11 0.22 0.19 0.12 0.10 0.10 0.08 0.12

B

K

94 81 70

93 81

BORING

Cast Aluminium

30

C2 C2 C2 C2

160

228 122 368 245

198 107 328 220

- -

180

79

Wrought Aluminium

30

292 195

390 260 105

180

N

Aluminium Bronze

100 - 200 C2 200 - 250 C2

73 55

95 81

85 68

87

Brass

100

C2 C2

112

160 105

138

185 117

Copper

60

68

85

0.04

C

Contact our Application Engineering department for assistance when machining these materials

REAMING

Deep Hole Drilling Speed and Feed Adjustment Holder Length

Recommended Speed and Feed Example If the recommended speed and feed is 50 m/min and 0.20 mm/rev for a standard length holder, then the speed and feed using a 3XL holder in the same application would be 37.5 m/min and 0.18 mm/rev.

Extended Long

Long Plus

XL

3XL

Speed

0.90

0.85 0.95

0.80 0.90

0.80 0.90

0.75 0.90

50 • 0.75 = 37.5 m/min

0.20 • 0.90 = 0.18 mm/rev

Feed

-

Formulas 1. RPM = (318.47 • m/min) / DIA

D

2. mm/min = RPM • mm/rev

3. m/min = RPM • 0.003 • DIA

where:

where:

where:

RPM

= revolutions per minute (rev/min)

mm/min = mm per minute (mm/min)

m/min = speed (m/min)

BURNISHING

m/min = speed (m/min)

RPM

= revolutions per minute (rev/min)

RPM

= revolutions per minute (rev/min)

DIA

= diameter of drill (mm)

mm/rev = feed rate (mm/rev)

DIA

= diameter of drill (mm)

E

THREADING

X

Tool failure can cause serious injury. To prevent: - When using holders without support bushing, use a short T-A® holder to establish an initial hole that is a minimum of 2 diameters deep. - Do not rotate tool holder more than 50 RPM unless it is engaged with the workpiece or fixture. Visit www.alliedmachine.com/DeepHoleGuidelines for the most up-to-date information and procedures. Factory technical assistance is available for your specific applications through our Application Engineering Team. WARNING

SPECIALS

www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com

A30: 123

Made with FlippingBook - Online Brochure Maker