A30-TAS_EU-EN

0

DRILLING | T-A® Replaceable Insert Drilling System

T-A Drill Insert Holders 0 Series | Flange Shank | Diameter Range: 12.98 mm - 17.65 mm (0.511" - 0.695")

A

L 1

DRILLING

L 7

L 4

D 2

L 2

P 1

L 3

B

L 1

L 7

L 4

BORING

D 2

P 1

P 2

L 2

Stub Length

L 3

Straight Flute

C

Body

Shank

REAMING

L 2

L 4

L 3

L 1

D 2 20 20 20 20 20 20 20 20 20 20

L 7

P 1

Series

Length

Part No.

21000S-20FM 22000S-20FM 24000S-20FM 25000S-20FM 27000S-20FM 29000S-20FM 21005S-20FM 22005S-20FM 24005S-20FM 25005S-20FM 21000S-075F 22000S-075F 24000S-075F 25000S-075F 21005S-075F 22005S-075F 24005S-075F 25005S-075F

Stub Short

23.1 30.9 59.6

47.6 63.5 92.1

50.3 66.2 94.8

97.6

50.0 50.0 50.0 50.0 50.0 50.0 50.0 50.0 50.0 50.0

1/8 BSPT 1/8 BSPT 1/8 BSPT 1/8 BSPT 1/8 BSPT 1/8 BSPT 1/8 BSPT 1/8 BSPT 1/8 BSPT 1/8 BSPT 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT

113.5 142.1 192.9 373.9 465.9 113.5 142.1 192.9 3.905 4.530 5.655 7.655 3.905 4.530 5.655 7.655 97.6

Standard Extended

0

110.4 291.3 383.3

142.9 323.9 415.9

145.6 326.6 418.6

XL

3XL

Stub Short

24.0 29.6 58.9

47.6 63.5 92.1

50.3 66.2 94.8

0.5

Standard Extended

D

109.7

142.9

145.6

BURNISHING

Stub Short

0.910 1.220 2.345 4.345 0.945 1.195 2.320 4.320

1.875 2.500 3.625 5.625 1.875 2.500 3.625 5.625

1.982 2.607 3.732 5.732 1.982 2.607 3.732 5.732

3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4

2.030 2.030 2.030 2.030 2.030 2.030 2.030 2.030

0

Standard Extended

Stub Short

0.5

Standard Extended

NOTE: Stub length holders have a 1/8" side pipe tap ( P 2 ). NOTE: 0.5 series inserts fit into both 0 and 0.5 series holders. However, 0 series inserts ONLY fit into 0 series holders. See page A30: 7 for visual .

E

THREADING

ConnecƟon Accessories

Admissible Tightening Torque* 175 N-cm (15.5 in-lbs) 175 N-cm (15.5 in-lbs)

Series

Insert Screws 72556-IP8-1 72567-IP8-1

Nylon Locking Screws

Insert Driver

Replacement Tips

Preset Torque Hand Driver

0

72556N-IP8-1 72567N-IP8-1

8IP-8 8IP-8

8IP-8TL 8IP-8TL

8IP-8B 8IP-8B

0.5

*Tightening torques are calculated with a fricƟon coefficient of µ = 0.14 and develop 90% of ulƟmate yield strength.

A30: 32 - 37

A30: 43 & 111

X

Key on A30: 1

= Metric (mm) = Imperial (in) Screws sold in quanƟƟes of 10.

SPECIALS

Refer to Speed and Feed charts for recommended adjustments to speeds and feeds. Refer to page A30: 146 for deep hole drilling guidelines in this secƟon of the catalogue. Visit www.alliedmachine.com/DeepHoleGuidelines for the most up-to-date informaƟon and procedures. Factory technical assistance is available for your specific applicaƟons through our ApplicaƟon Engineering Team. WARNING

A30: 38

www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com