A30-TAS_EU-EN

0

DRILLING | T-A® Replaceable Insert Drilling System

T-A Drill Insert Holders 0 Series | Straight Shank | ER Collet | Diameter Range: 12.98 mm - 17.65 mm (0.511" - 0.695")

A

L 1

DRILLING

L 7

L 4

D 2

L 2

P

1

L 3

Straight Flute

B

Body

Shank

Series

Length

Part No.

L 2

L 4

L 3

L 1

D 2

L 7

P 1

BORING

22000S-075L 24000S-075L 25000S-075L 26000S-075L 27000S-075L 29000S-075L 22005S-075L 24005S-075L 25005S-075L

Short

1-3/8 2-1/2 4-1/2

2-3/16 3-5/16 5-5/16 7-13/16 12-7/16 16-1/16 2-3/16 3-5/16 5-5/16 7-13/16

2-19/64 3-27/64 5-27/64 7-59/64 16-11/64 2-19/64 3-27/64 5-27/64 7-59/64

4-9/16 5-11/16 7-11/16 10-3/16 18-7/16 4-9/16 5-11/16 7-11/16 10-3/16

3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4

2-3/8 2-3/8 2-3/8 2-3/8 2-3/8 2-3/8 2-3/8 2-3/8 2-3/8 2-3/8

1/8 1/8 1/8 1/8 1/8 1/8

Standard Extended

0

Long

7

XL

11-5/8 15-1/4

12-35/64 14-13/16

3XL

Short

1-3/8 2-1/2 4-1/2

1/8* 1/8* 1/8* 1/8*

Standard Extended

0.5

C

Long 26005S-075L NOTE: 0.5 series inserts fit into both 0 and 0.5 series holders. However, 0 series inserts ONLY fit into 0 series holders. See page A30: 7 for visual . 7

REAMING

L 1

L 4

D

L 2

ER

BURNISHING

L 3

ER Collet Holder

Body

Collet Nut without Retaining Ring

Series

Part No.

L 2

L 4

L 3

L 1

ER

21000S-16ER 21000S-20ER

1-3/8 1-3/8

1-57/64 1-57/64

2 2

3-5/64 3-15/64

ER-16 ER-20

ER-16N ER-20N

0

Connection Accessories

E

Admissible Tightening Torque* 175 N-cm (15.5 in-lbs) 175 N-cm (15.5 in-lbs)

Series

Insert Screws 72556-IP8-1 72567-IP8-1

Nylon Locking Screws

Insert Driver

Replacement Tips

Preset Torque Hand Driver

THREADING 0

72556N-IP8-1 72567N-IP8-1

8IP-8 8IP-8

8IP-8TL 8IP-8TL

8IP-8B 8IP-8B

0.5

*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength

A30: 32 - 37

A30: 43 & 111

X

Key on A30: 1

= Metric (mm) = Imperial (in) Screws sold in quantities of 10

SPECIALS

Refer to Speed and Feed charts for recommended adjustments to speeds and feeds. Refer to page A30: 146 for deep hole drilling guidelines in this section of the catalogue. Visit www.alliedmachine.com/DeepHoleGuidelines for the most up-to-date information and procedures. Factory technical assistance is available for your specific applications through our Application Engineering Team. WARNING

A30: 42

www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com