A30-TAS_EU-EN
1
DRILLING | T-A® Replaceable Insert Drilling System
T-A Drill Insert Holders 1 Series | Straight Shank | Diameter Range: 17.53 mm - 24.38 mm (0.690" - 0.960")
A
L 1
L 4
L 7
DRILLING
D 2
L 2
P 1
L 3
Straight Flute
B
Body
Shank
L 2
L 4
L 3
L 1
D 2
L 7
P 1
Series
Length
Part No.
BORING
22010S-075L 22010S-100L 23010S-100L 24010S-075L 24010S-100L 25010S-100L 27010S-100L 29010S-100L 22015S-075L 22015S-100L 23015S-100L 24015S-075L 24015S-100L
Short Short
2.619 2.647 4.647 6.619 6.647
3.875 3.875 5.875 7.875 7.875
4.015 4.015 6.015 8.015 8.015
6.875 6.875 8.875
3/4
3.000 3.000 3.000 3.000 3.000 3.000 3.000 3.000 3.000 3.000 3.000 3.000 3.000 3.000
1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT
1 1
Intermediate
Standard Standard Extended
10.875 10.875 14.875 22.250 26.500
3/4
1
1 1 1 1
10.647 18.022 22.272
11.875 19.250 23.500
12.015 19.390 23.640
XL
3XL
Short Short
2.649 2.661 4.661 6.649 6.661
3.875 3.875 5.875 7.875 7.875
4.015 4.015 6.015 8.015 8.015
6.875 6.875 8.875
3/4
C
1 1
Intermediate
1.5
Standard Standard Extended
10.875 10.875 14.875
3/4
REAMING
1 1
10.661 25015S-100L NOTE: 1.5 series inserts fit into both 1 and 1.5 series holders. However, 1 series inserts ONLY fit into 1 series holders. See page A30: 7 for visual . 11.875 12.015
D
BURNISHING
E
THREADING
ConnecƟon Accessories
Admissible Tightening Torque* 305 N-cm (27.0 in-lbs) 305 N-cm (27.0 in-lbs)
Series
Insert Screws
Nylon Locking Screws
Insert Driver
Replacement Tips
Preset Torque Hand Driver
1
7375-IP9-1 739-IP9-1
7375N-IP9-1 739N-IP9-1
8IP-9 8IP-9
8IP-9TL 8IP-9TL
8IP-9B 8IP-9B
1.5
*Tightening torques are calculated with a fricƟon coefficient of µ = 0.14 and develop 90% of ulƟmate yield strength.
A30: 44 - 51
A30: 57 & 111
X
Key on A30: 1
= Metric (mm) = Imperial (in) Screws sold in quanƟƟes of 10.
SPECIALS
Refer to Speed and Feed charts for recommended adjustments to speeds and feeds. Refer to page A30: 146 for deep hole drilling guidelines in this secƟon of the catalogue. Visit www.alliedmachine.com/DeepHoleGuidelines for the most up-to-date informaƟon and procedures. Factory technical assistance is available for your specific applicaƟons through our ApplicaƟon Engineering Team. WARNING
A30: 56
www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com
Made with FlippingBook - Online Brochure Maker