A30-TAS_EU-EN

2

DRILLING | T-A® Replaceable Insert Drilling System

T-A Drill Insert Holders 2 Series | Taper Shank | Diameter Range: 24.41 mm - 35.05 mm (0.961" - 1.380")

A

L 1

L 4

DRILLING

P 2

MT

RCA

L 2

L 3

Helical Flute

B

Body

Shank

Series

Length

RCA

Part No.

L 2

L 4

L 3

L 1

MT

P 2

BORING

23020H-004M 24020H-004M 25020H-004M 23025H-004M 24025H-004M 25025H-004M 23020H-004I 24020H-003I 24020H-004I 25020H-004I 23025H-004I 24025H-003I 24025H-004I 25025H-004I

Intermediate

136.5 187.3 289.0 136.5 187.3 289.0 5-3/8 7-3/8 7-3/8 11-3/8

165.1 215.9 317.5 165.1 215.9 317.5 6-1/2 8-1/2 8-1/2 12-1/2

211.2 262.0 363.6 218.4 269.2 370.8

324.6 375.4 477.0 331.8 382.6 484.2

#4** #4** #4** #4** #4** #4**

1/8* 1/8* 1/8* 1/4* 1/4* 1/4*

2T-3SRM 2T-3SRM 2T-3SRM 2T-4SRM 2T-4SRM 2T-4SRM

2

Standard Extended

Intermediate

2.5

Standard Extended

Intermediate Standard Standard Extended Standard Standard Extended Intermediate

8-19/64

12-25/32

#4 #3 #4 #4 #4 #3 #4 #4

1/8 1/8 1/8 1/8 1/4 1/8 1/4 1/4

2T-3SR 2T-3SR 2T-3SR 2T-3SR 2T-4SR 2T-3SR 2T-4SR 2T-4SR

10-15/64 13-25/32 10-19/64 14-25/32 14-15/64 18-25/32

2

C

5-3/8 7-3/8 7-3/8

6-1/2 8-1/2 8-1/2

8-37/64

13-1/16

REAMING

10-15/64 13-25/32

2.5

10-37/64 14-37/64

15-1/16 19-1/16

11-3/8

12-1/2

*Metric thread to BSP and ISO 7-1 **Per ISO 296 type BEK NOTE: 2.5 series inserts fit into both 2 and 2.5 series holders. However, 2 series inserts ONLY fit into 2 series holders. See page A30: 7 for visual .

D

BURNISHING

E

THREADING

Connection Accessories

Admissible Tightening Torque* 690 N-cm (61.0 in-lbs)

Insert Screws 7495-IP15-1

Nylon Locking Screws

Insert Driver

Replacement Tips

Preset Torque Hand Driver

7495N-IP15-1

8IP-15

8IP-15TL

8IP-15B

*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength

A30: 58 - 67

A30: 73 & 110

X

Key on A30: 1

= Metric (mm) = Imperial (in) Screws sold in quantities of 10

SPECIALS

Refer to Speed and Feed charts for recommended adjustments to speeds and feeds. Refer to page A30: 146 for deep hole drilling guidelines in this section of the catalogue. Visit www.alliedmachine.com/DeepHoleGuidelines for the most up-to-date information and procedures. Factory technical assistance is available for your specific applications through our Application Engineering Team. WARNING

www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com

A30: 71

Made with FlippingBook - Online Brochure Maker