B10-G_US-EN

BORING | Large Diameter Boring

Serrated Slide Basic D 60 Accessories Clamping Pieces | Cover Plates

A

1

B

5

3

C

4

Clamping pieces for 538 (537) cassettes and counter weights sold seperatly. (See page B10-G: 20)

D

2

Clamping Pieces

Serrated Slide Part No. 350051 350052 350053 350054 349051 349052 349053 349054

2 Clamping Nut

3 Adjustment Pin

1 Cap Screw

4 Thread Pin

5 Cap Screw

E

Connection

Part No. 115118 115118 115118 115118 115118 115118 115118 115118

Service Key Part No.

Part No. 141112 141113 141114 141115 141112 141113 141114 141115

Part No. 115196 115196 115196 115196 115196 115196 115196 115196

Service Key Part No.

Service Key

115669 115669 115669 115669 115669 115669 115669 115669

115170 115170 115170 115170 115170 115170 115170 115170

D 60 D 60 D 60 D 60 D 60 D 60 D 60 D 60

s8 / B s8 / B s8 / B s8 / B s8 / B s8 / B s8 / B s8 / B

s4 / F s4 / F s4 / F s4 / F s4 / F s4 / F s4 / F s4 / F

s14 / C s14 / C s14 / C s14 / C s14 / C s14 / C s14 / C s14 / C

F

G

Cover Plates for Basic D 60 Serrated Slides

H

Serrated Slide 1 Cover Plate 2 Countersunk Screw

1

Connection

Part No. 350051 350052 350053 350054 349051 349052 349053 349054

Part No. 349016 349017 349017 349017 349016 349017 349017 349017

Part No. 063106 063106 063106 063106 063106 063106 063106 063106

Service Key

D 60 D 60 D 60 D 60 D 60 D 60 D 60 D 60

s4 / B s4 / B s4 / B s4 / B s4 / B s4 / B s4 / B s4 / B

I

2

J

K

B10-M: 12-15

B10: vi-vii

Key on B10-G: 1

19.5-22 22-11

40-22 50-28 63-36 80-36 100-56

= Imperial (in) = Metric (mm)

25-14 32-18

L

Exceeding weight capacity for machine tool spindle and tool changer can cause machine damage and/or serious injury. To prevent: -Consult machine tool builder for machine's weight limitations. -Refer to example on page B10-M: 11 for calculating tool assembly weight Factory technical assistance is also available for specific applications through our Application Engineering department. ext: 7611 | email: appeng@alliedmachine.com WARNING

Tool failure can cause serious injury. To prevent: -Do not exceed recommended 10xD length-to-diameter ratio or exceed 4 total components (including shank) -When using Alu-Line components, do not exceed recommended 5xD length-to-diameter ratio -When using tool steel components, do not exceed recommended 6xD length-to-diameter ratio -When using heavy metal components, do not exceed recommended 8xD length-to-diameter ratio WARNING

M

-When using a carbide shank, do not exceed recommended 9xD length-to-diameter ratio -When using a NOVI TECH module, do not exceed recommended 10xD length-to-diameter ratio -Refer to examples on pages B10-M: 8-10 for calculating length-to-diameter ratio Factory technical assistance is available for your specific applications through our Application Engineering department. ext: 7611 | email: appeng@alliedmachine.com

INDEX

www.alliedmachine.com | 1.330.343.4283

B10-G: 23