Drilling Product Catalog

DRILLING | T-A® Replaceable Insert Drilling System

1 Series: 17.53 mm - 24.40 mm (0.6900" - 0.9609")

T-A® Drill Holders

Imperial Taper Shank Holders

Body

Shank

L 2

L 4

L 3

L 1

MT

P 2

Flute

Series

Length

RCA

Part No.

A30

22010S-003I 22010S-004I 23010S-003I 24010S-003I 24010S-004I 25010S-003I 22015S-003I 22015S-004I 23015S-003I 24015S-003I 24015S-004I 25015S-003I 23010H-003I 24010H-003I 24010H-004I 25010H-003I 23015H-003I 24015H-003I 24015H-004I

Short Short

2.631 3.875 5.608 9.156 #3 MT 2.631 3.875 5.671 10.156 #4 MT

1/8 NPT 2T-3SR 1/8 NPT 2T-3SR 1/8 NPT 2T-3SR 1/8 NPT 2T-3SR 1/8 NPT 2T-3SR 1/8 NPT 2T-3SR 1/8 NPT 2T-3SR 1/8 NPT 2T-3SR 1/8 NPT 2T-3SR 1/8 NPT 2T-3SR 1/8 NPT 2T-3SR 1/8 NPT 2T-3SR 1/8 NPT 2T-3SR 1/8 NPT 2T-3SR 1/8 NPT 2T-3SR 1/8 NPT 2T-3SR 1/8 NPT 2T-3SR 1/8 NPT 2T-3SR 1/8 NPT 2T-3SR 1/8 NPT 2T-3SR

Intermediate 4.631 5.875 7.608 11.156 #3 MT Standard 6.631 7.875 9.608 13.156 #3 MT Standard 6.631 7.875 9.671 14.156 #4 MT

1

Extended

10.631 11.875 13.608 17.156 #3 MT 2.482 3.875 5.608 9.156 #3 MT 2.483 3.875 5.671 10.156 #4 MT

Short Short

Straight

Intermediate 4.482 5.875 7.608 11.156 #3 MT Standard 6.482 7.875 9.608 13.156 #3 MT Standard 6.483 7.875 9.671 14.156 #4 MT 1 Intermediate 5.236 5.875 7.608 11.156 #3 MT Standard 7.236 7.875 9.608 13.156 #3 MT Standard 7.236 7.875 9.671 14.156 #4 MT Extended 10.482 11.875 13.608 17.156 #3 MT Intermediate 5.219 5.875 7.608 11.156 #3 MT Standard 7.219 7.875 9.608 13.156 #3 MT Standard 7.219 7.875 9.671 14.156 #4 MT Extended 11.236 11.875 13.608 17.156 #3 MT

1.5

Helical

1.5

Extended 25015H-003I NOTE : 0.5 series inserts fit into both 0 and 0.5 series holders. However, 0 series inserts ONLY fit into 0 series holders. See page A30: 7 for visual . 11.219 11.875 13.608 17.156 #3 MT

Connection Accessories

Admissible Tightening Torque* 305 N-cm (27.0 in-lbs) 305 N-cm (27.0 in-lbs)

Nylon Locking Screws 7375N-IP9-1

Preset Torque Hand Driver

Series

Insert Screws

Insert Driver

Replacement Tips

1

7375-IP9-1 739-IP9-1

8IP-9 8IP-9

8IP-9TL 8IP-9TL

8IP-9B 8IP-9B

1.5

739N-IP9-1

*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength.

Refer to Speed and Feed charts for recommended adjustments to speeds and feeds. Refer to page A30: 146 for deep hole drilling guidelines in this section of the catalog. Visit www.alliedmachine.com/DeepHoleGuidelines for the most up-to-date information and procedures. Factory technical assistance is available for your specific applications through our Application Engineering department : appeng@alliedmachine.com. WARNING

A30: 113 - 139

A30: 47 - 54

A30: 60 & 111 A30: 60 & 112

Key on A30: 2

Screws sold in multiples of 10. = Metric (mm) = Imperial (in)

www.alliedmachine.com | 1.330.343.4283

A30: 58