Drilling Product Catalog

DRILLING | T-A® Replaceable Insert Drilling System

1 Series: 17.53 mm - 24.40 mm (0.6900" - 0.9609")

T-A® Drill Holders

Straight Shank Holders

Body

Shank

L 2

L 4

L 3

L 1

L 5

D 2

P 1

Flute

Series

Length

Part No.

A30

22010S-075L 22010S-100L 23010S-100L 24010S-075L 24010S-100L 25010S-100L 27010S-100L 29010S-100L 22015S-075L 22015S-100L 23015S-100L 24015S-075L 24015S-100L

Short Short

2.619 3.875 4.015 6.875 3.000 3/4 2.647 3.875 4.015 6.875 3.000 1 4.647 5.875 6.015 8.875 3.000 1

1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT 1/8 NPT

Intermediate

Standard 6.619 7.875 8.015 10.875 3.000 3/4 Standard 6.647 7.875 8.015 10.875 3.000 1

1

Extended

10.647 11.875 12.015 14.875 3.000 1 18.022 19.250 19.390 22.250 3.000 1 22.272 23.500 23.640 26.500 3.000 1 2.649 3.875 4.015 6.875 3.000 3/4 2.661 3.875 4.015 6.875 3.000 1 4.661 5.875 6.015 8.875 3.000 1

XL

3XL

Straight

Short Short

Intermediate

1.5

Standard 6.649 7.875 8.015 10.875 3.000 3/4 Standard 6.661 7.875 8.015 10.875 3.000 1

Extended 25015S-100L NOTE: 1.5 series inserts fit into both 1 and 1.5 series holders. However, 1 series inserts ONLY fit into 1 series holders. See page A30: 7 for visual . 10.661 11.875 12.015 14.875 3.000 1

Connection Accessories

Admissible Tightening Torque* 305 N-cm (27.0 in-lbs) 305 N-cm (27.0 in-lbs)

Nylon Locking Screws 7375N-IP9-1

Preset Torque Hand Driver

Series

Insert Screws

Insert Driver

Replacement Tips

1

7375-IP9-1 739-IP9-1

8IP-9 8IP-9

8IP-9TL 8IP-9TL

8IP-9B 8IP-9B

1.5

739N-IP9-1

*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength.

Refer to Speed and Feed charts for recommended adjustments to speeds and feeds. Refer to page A30: 146 for deep hole drilling guidelines in this section of the catalog. Visit www.alliedmachine.com/DeepHoleGuidelines for the most up-to-date information and procedures. Factory technical assistance is available for your specific applications through our Application Engineering department : appeng@alliedmachine.com. WARNING

A30: 113 - 139

A30: 47 - 54

A30: 60 & 112

Key on A30: 2

Screws sold in multiples of 10. = Metric (mm) = Imperial (in)

A30: 59

www.alliedmachine.com | 1.330.343.4283