AMPC_EU-EN

1

DRILLING | T-A Pro® High PenetraƟon Replaceable Insert Drilling System

T-A Pro Drill Holders 1 Series Metric | Diameter Range: 17.65 mm - 24.37 mm

A

L 1

L 5

L 4

DRILLING

D 2

L 2

L 3

Body

Shank

B

L 2

L 4

L 3

L 1

L 5

D 2 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25

Length Sub Series

Flat Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No

Part No

HTA1A01-25FM HTA1A01-25CM HTA1B01-25FM HTA1B01-25CM HTA1C01-25FM HTA1C01-25CM HTA1D01-25FM HTA1D01-25CM HTA1A03-25FM HTA1A03-25CM HTA1B03-25FM HTA1B03-25CM HTA1C03-25FM HTA1C03-25CM HTA1D03-25FM HTA1D03-25CM HTA1A05-25FM HTA1A05-25CM HTA1B05-25FM HTA1B05-25CM HTA1C05-25FM HTA1C05-25CM HTA1D05-25FM HTA1D05-25CM HTA1A07-25FM HTA1A07-25CM HTA1B07-25FM HTA1B07-25CM HTA1C07-25FM HTA1C07-25CM HTA1D07-25FM HTA1D07-25CM

Stub Stub Stub Stub Stub Stub Stub Stub 3xD 3xD 3xD 3xD 3xD 3xD 3xD 3xD 5xD 5xD 5xD 5xD 5xD 5xD 5xD 5xD 7xD 7xD 7xD 7xD 7xD 7xD 7xD 7xD

A A B B C C D D A A B B C C D D A A B B C C D D A A B B C C D D

21.0 21.0 21.0 21.0 21.0 21.0 21.0 21.0 62.9 62.9 62.9 62.9 62.9 62.9 62.9 62.9

56.5 56.5 56.5 56.5 56.5 56.5 56.5 56.5

60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0

112.5 112.5 112.5 112.5 112.5 112.5 112.5 112.5 156.9 156.9 156.9 156.9 156.9 156.9 156.9 156.9 198.8 198.8 198.8 198.8 198.8 198.8 198.8 198.8 240.7 240.7 240.7 240.7 240.7 240.7 240.7 240.7

56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0

BORING

100.9 100.9 100.9 100.9 100.9 100.9 100.9 100.9 142.8 142.8 142.8 142.8 142.8 142.8 142.8 142.8 184.7 184.7 184.7 184.7 184.7 184.7 184.7 184.7

104.5 104.5 104.5 104.5 104.5 104.5 104.5 104.5 146.4 146.4 146.4 146.4 146.4 146.4 146.4 146.4 188.3 188.3 188.3 188.3 188.3 188.3 188.3 188.3

C

REAMING

104.8 104.8 104.8 104.8 104.8 104.8 104.8 104.8 146.7 146.7 146.7 146.7 146.7 146.7 146.7 146.7

D

BURNISHING

E

ConnecƟon Accessories

1 Series Holder Diameter Range Metric (mm)

Admissible Tightening Torque*

THREADING Sub Series

Imperial (inch)

Replacement Tips

Preset Torque Hand Driver

Insert Screws

Nylon Locking Screws

Insert Driver

1A 1B 1C 1D

17.65 mm - 24.37 mm 0.6947" - 0.9596" 19.05 mm - 24.37 mm 0.7499" - 0.9596" 20.60 mm - 24.37 mm 0.8109" - 0.9596" 22.90 mm - 24.37 mm 0.9014" - 0.9596"

A/B 7375-IP9-1 7375N-IP9-1

8IP-9 8IP-9

8IP-9TL 8IP-9TL

8IP-9B 305 N-cm (27.0 in-lbs)

C/D 739-IP9-1 8IP-9B 305 N-cm (27.0 in-lbs) *Tightening torques are calculated with a fricƟon coefficient of µ = 0.14 and develop 90% of ulƟmate yield strength. 739N-IP9-1

Refer to Speed and Feed charts for recommended adjustments to speeds and feeds. Refer to page A25: 58 for deep hole drilling guidelines in this secƟon of the catalogue. Visit www.alliedmachine.com/DeepHoleGuidelines for the most up-to-date informaƟon and procedures. Factory technical assistance is available for your specific applicaƟons through our ApplicaƟon Engineering department. emai l : engineering.eu@alliedmachine.com WARNING

X

A25: 24 - 27

A25: 48 - 55

SPECIALS

Key on A25: 1

Screws sold in mulƟples of 10. = Metric (mm) = Imperial (in)

A25: 28

www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com