AMPC_EU-EN

1

DRILLING | T-A Pro® High PenetraƟon Replaceable Insert Drilling System

T-A Pro Drill Holders 1 Series Metric | Diameter Range: 17.65 mm - 24.37 mm

A

L 1

L 5

L 4

DRILLING

D 2

L 2

L 3

Body

Shank

B

L 2

L 4

L 3

L 1

L 5

D 2 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25

Length Sub Series

Flat Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No

Part No

HTA1A10-25FM HTA1A10-25CM HTA1B10-25FM HTA1B10-25CM HTA1C10-25FM HTA1C10-25CM HTA1D10-25FM HTA1D10-25CM HTA1A12-25FM HTA1A12-25CM HTA1B12-25FM HTA1B12-25CM HTA1C12-25FM HTA1C12-25CM HTA1D12-25FM HTA1D12-25CM HTA1A15-25FM HTA1A15-25CM HTA1B15-25FM HTA1B15-25CM HTA1C15-25FM HTA1C15-25CM HTA1D15-25FM HTA1D15-25CM

10xD 10xD 10xD 10xD 10xD 10xD 10xD 10xD 12xD 12xD 12xD 12xD 12xD 12xD 12xD 12xD 15xD 15xD 15xD 15xD 15xD 15xD 15xD 15xD

A A B B C C D D A A B B C C D D A A B B C C D D

209.6 209.6 209.6 209.6 209.6 209.6 209.6 209.6 251.5 251.5 251.5 251.5 251.5 251.5 251.5 251.5 314.3 314.3 314.3 314.3 314.3 314.3 314.3 314.3

247.6 247.6 247.6 247.6 247.6 247.6 247.6 247.6 289.5 289.5 289.5 289.5 289.5 289.5 289.5 289.5 352.4 352.4 352.4 352.4 352.4 352.4 352.4 352.4

251.2 251.2 251.2 251.2 251.2 251.2 251.2 251.2 293.1 293.1 293.1 293.1 293.1 293.1 293.1 293.1 355.9 355.9 355.9 355.9 355.9 355.9 355.9 355.9

303.6 303.6 303.6 303.6 303.6 303.6 303.6 303.6 345.5 345.5 345.5 345.5 345.5 345.5 345.5 345.5 408.4 408.4 408.4 408.4 408.4 408.4 408.4 408.4

56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0 56.0

BORING

C

REAMING

D

BURNISHING

E

ConnecƟon Accessories

1 Series Holder Diameter Range Metric (mm)

Admissible Tightening Torque*

Sub Series

THREADING

Imperial (inch)

Replacement Tips

Preset Torque Hand Driver

Insert Screws

Nylon Locking Screws

Insert Driver

1A 1B 1C 1D

17.65 mm - 24.37 mm 0.6947" - 0.9596" 19.05 mm - 24.37 mm 0.7499" - 0.9596" 20.60 mm - 24.37 mm 0.8109" - 0.9596" 22.90 mm - 24.37 mm 0.9014" - 0.9596"

A/B 7375-IP9-1 7375N-IP9-1

8IP-9 8IP-9

8IP-9TL 8IP-9TL

8IP-9B 305 N-cm (27.0 in-lbs)

C/D 739-IP9-1 8IP-9B 305 N-cm (27.0 in-lbs) *Tightening torques are calculated with a fricƟon coefficient of µ = 0.14 and develop 90% of ulƟmate yield strength. 739N-IP9-1

Refer to Speed and Feed charts for recommended adjustments to speeds and feeds. Refer to page A25: 58 for deep hole drilling guidelines in this secƟon of the catalogue. Visit www.alliedmachine.com/DeepHoleGuidelines for the most up-to-date informaƟon and procedures. Factory technical assistance is available for your specific applicaƟons through our ApplicaƟon Engineering department. emai l : engineering.eu@alliedmachine.com WARNING

X

A25: 24 - 27

A25: 48 - 55

SPECIALS

Key on A25: 1

Screws sold in mulƟples of 10. = Metric (mm) = Imperial (in)

www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com

A25: 29