AMPC_EU-EN

2

DRILLING | T-A Pro® High PenetraƟon Replaceable Insert Drilling System

T-A Pro Drill Holders

2 Series Metric | Diameter Range: 24.38 mm - 35.04 mm

A

L 1

L 5

L 4

DRILLING

D 2

L 2

L 3

Body

Shank

B

L 2

L 4

L 3

L 1

L 5

D 2 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32

Length Sub Series

Flat Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No

Part No

HTA2A01-32FM HTA2A01-32CM HTA2B01-32FM HTA2B01-32CM HTA2C01-32FM HTA2C01-32CM HTA2D01-32FM HTA2D01-32CM HTA2A03-32FM HTA2A03-32CM HTA2B03-32FM HTA2B03-32CM HTA2C03-32FM HTA2C03-32CM HTA2D03-32FM HTA2D03-32CM HTA2A05-32FM HTA2A05-32CM HTA2B05-32FM HTA2B05-32CM HTA2C05-32FM HTA2C05-32CM HTA2D05-32FM HTA2D05-32CM HTA2A07-32FM HTA2A07-32CM HTA2B07-32FM HTA2B07-32CM HTA2C07-32FM HTA2C07-32CM HTA2D07-32FM HTA2D07-32CM

Stub Stub Stub Stub Stub Stub Stub Stub 3xD 3xD 3xD 3xD 3xD 3xD 3xD 3xD 5xD 5xD 5xD 5xD 5xD 5xD 5xD 5xD 7xD 7xD 7xD 7xD 7xD 7xD 7xD 7xD

A A B B C C D D A A B B C C D D A A B B C C D D A A B B C C D D

29.7 29.7 29.7 29.7 29.7 29.7 29.7 29.7 89.2 89.2 89.2 89.2 89.2 89.2 89.2 89.2

75.0 75.0 75.0 75.0 75.0 75.0 75.0 75.0

78.6 78.6 78.6 78.6 78.6 78.6 78.6 78.6

135.0 135.0 135.0 135.0 135.0 135.0 135.0 135.0 197.4 197.4 197.4 197.4 197.4 197.4 197.4 197.4 256.9 256.9 256.9 256.9 256.9 256.9 256.9 256.9 316.4 316.4 316.4 316.4 316.4 316.4 316.4 316.4

60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0

BORING

137.4 137.4 137.4 137.4 137.4 137.4 137.4 137.4 196.9 196.9 196.9 196.9 196.9 196.9 196.9 196.9 256.4 256.4 256.4 256.4 256.4 256.4 256.4 256.4

141.0 141.0 141.0 141.0 141.0 141.0 141.0 141.0 200.5 200.5 200.5 200.5 200.5 200.5 200.5 200.5 260.0 260.0 260.0 260.0 260.0 260.0 260.0 260.0

C

REAMING

148.7 148.7 148.7 148.7 148.7 148.7 148.7 148.7 208.2 208.2 208.2 208.2 208.2 208.2 208.2 208.2

D

BURNISHING

E

ConnecƟon Accessories

2 Series Holder Diameter Range Metric (mm)

Admissible Tightening Torque*

THREADING Sub Series

Imperial (inch)

Replacement Tips

Preset Torque Hand Driver

Insert Screws

Nylon Locking Screws

Insert Driver

2A 2B 2C 2D

24.38 mm - 35.04 mm 0.9597" - 1.3797" 25.40 mm - 35.04 mm 0.9999" - 1.3797" 28.50 mm - 35.04 mm 1.1219" - 1.3797" 31.70 mm - 35.04 mm 1.2479" - 1.3797"

7495-IP15-1 7495N-IP15-1 8IP-15

8IP-15TL

8IP-15B 690 N-cm (61.0 in-lbs)

*Tightening torques are calculated with a fricƟon coefficient of µ = 0.14 and develop 90% of ulƟmate yield strength.

Refer to Speed and Feed charts for recommended adjustments to speeds and feeds. Refer to page A25: 58 for deep hole drilling guidelines in this secƟon of the catalogue. Visit www.alliedmachine.com/DeepHoleGuidelines for the most up-to-date informaƟon and procedures. Factory technical assistance is available for your specific applicaƟons through our ApplicaƟon Engineering department. emai l : engineering.eu@alliedmachine.com WARNING

X

A25: 32 - 35

A25: 48 - 55

SPECIALS

Key on A25: 1

Screws sold in mulƟples of 10. = Metric (mm) = Imperial (in)

A25: 36

www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com