AMPC_EU-EN

2

DRILLING | T-A Pro® High PenetraƟon Replaceable Insert Drilling System

T-A Pro Drill Holders

2 Series Metric | Diameter Range: 24.38 mm - 35.04 mm

A

L 1

L 5

L 4

DRILLING

D 2

L 2

L 3

Body

Shank

B

L 2

L 4

L 3

L 1

L 5

D 2 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32

Length Sub Series

Flat Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No

Part No

HTA2A10-32FM HTA2A10-32CM HTA2B10-32FM HTA2B10-32CM HTA2C10-32FM HTA2C10-32CM HTA2D10-32FM HTA2D10-32CM HTA2A12-32FM HTA2A12-32CM HTA2B12-32FM HTA2B12-32CM HTA2C12-32FM HTA2C12-32CM HTA2D12-32FM HTA2D12-32CM HTA2A15-32FM HTA2A15-32CM HTA2B15-32FM HTA2B15-32CM HTA2C15-32FM HTA2C15-32CM HTA2D15-32FM HTA2D15-32CM

10xD 10xD 10xD 10xD 10xD 10xD 10xD 10xD 12xD 12xD 12xD 12xD 12xD 12xD 12xD 12xD 15xD 15xD 15xD 15xD 15xD 15xD 15xD 15xD

A A B B C C D D A A B B C C D D A A B B C C D D

297.4 297.4 297.4 297.4 297.4 297.4 297.4 297.4 356.9 356.9 356.9 356.9 356.9 356.9 356.9 356.9 446.2 446.2 446.2 446.2 446.2 446.2 446.2 446.2

345.6 345.6 345.6 345.6 345.6 345.6 345.6 345.6 405.1 405.1 405.1 405.1 405.1 405.1 405.1 405.1 494.4 494.4 494.4 494.4 494.4 494.4 494.4 494.4

349.2 349.2 349.2 349.2 349.2 349.2 349.2 349.2 408.7 408.7 408.7 408.7 408.7 408.7 408.7 408.7 497.9 497.9 497.9 497.9 497.9 497.9 497.9 497.9

405.6 405.6 405.6 405.6 405.6 405.6 405.6 405.6 465.1 465.1 465.1 465.1 465.1 465.1 465.1 465.1 554.4 554.4 554.4 554.4 554.4 554.4 554.4 554.4

60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0

BORING

C

REAMING

D

BURNISHING

E

ConnecƟon Accessories

2 Series Holder Diameter Range Metric (mm)

Admissible Tightening Torque*

Sub Series

THREADING

Imperial (inch)

Replacement Tips

Preset Torque Hand Driver

Insert Screws

Nylon Locking Screws

Insert Driver

2A 2B 2C 2D

24.38 mm - 35.04 mm 0.9597" - 1.3797" 25.40 mm - 35.04 mm 0.9999" - 1.3797" 28.50 mm - 35.04 mm 1.1219" - 1.3797" 31.70 mm - 35.04 mm 1.2479" - 1.3797"

7495-IP15-1 7495N-IP15-1 8IP-15

8IP-15TL

8IP-15B 690 N-cm (61.0 in-lbs)

*Tightening torques are calculated with a fricƟon coefficient of µ = 0.14 and develop 90% of ulƟmate yield strength.

Refer to Speed and Feed charts for recommended adjustments to speeds and feeds. Refer to page A25: 58 for deep hole drilling guidelines in this secƟon of the catalogue. Visit www.alliedmachine.com/DeepHoleGuidelines for the most up-to-date informaƟon and procedures. Factory technical assistance is available for your specific applicaƟons through our ApplicaƟon Engineering department. emai l : engineering.eu@alliedmachine.com WARNING

X

A25: 32 - 35

A25: 48 - 55

SPECIALS

Key on A25: 1

Screws sold in mulƟples of 10. = Metric (mm) = Imperial (in)

www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com

A25: 37