B10-WHL

BORING | Inserts

Recommended Insert Application 80° Rhomboid Replaceable Inserts

ROUGH MACHINING | FORMS 101, 103, 104 AND 105

Insert

Cutting Speed*

Machining Conditions

ISO Material

Substrate Geometry

Grade

m/min

SFM

Low-Carbon Steel 1010, 1020, 1025, 1522, etc.

Carbide Carbide Carbide Carbide Carbide Carbide Carbide Carbide Carbide Carbide Carbide Carbide Carbide Carbide Ceramic Carbide Carbide Ceramic Carbide Carbide Carbide Carbide Carbide Carbide Carbide Carbide Carbide Carbide

109 192 199 109 192 199 199 158 192 199 146 192 146 192 711 192 146 711 129 860 129 127 860 199 192 200 860 199

WHC136 WHC164 WHC114 WHC136 WHC164 WHC114 WHC114 WHC111 WHC19 WHC114 WHC88 WHC19 WHC81 WHC164 WCN40 WHC164 WHC81 WCN40 WHW16 WHW01 WHW16 WHW16 WHW01 WHC114 WHC19 WHC111 WHC05 WHC114

150 - 250

492 - 820

Alloy Steel 4140, 5140, 8640, etc.

150 - 200

492 - 656

P

High-Strength Alloy 4340, 4330V, 300M, etc.

100 - 160

328 - 525

Stainless Steel

80 - 140

262 - 459

M

SG / Nodular Cast Iron

150 - 230

492 - 755

200 - 400

656 - 1312

K

Grey / White Iron

160 - 280

525 - 919

400 - 1000

1312 - 3281

Aluminum Alloys

250 - 800

820 - 2625

Nonferrous Metals

N

200 - 600

656 - 1969

High-Temp Alloy Hastelloy® B, Inconel® 600, etc.

30 - 60

98 - 197

Titanium Alloy

S

40 - 70

131 - 230

H Hardened Steel

Carbide

158

WHC111

40 - 60

131 - 197

*Not to exceed max recommended RPM for boring head found in corresponding Wohlhaupter Operation Manual.

Metric Feed Rate

Imperial Feed Rate

I

Nose Radius (mm)

mm/rev

Nose Radius (in)

IPR

0.1 0.2 0.4

0.004 0.008 0.016

0.10 - 0.35

0.004 - 0.014

Deep Hole Boring Speed Adjustment

Recommended Speed Example If the recommended speed for a finish boring assembly under 5xD is 120 m/min, then the speed for a 10xD finish boring assembly in the same application would be 60 m/min (120 m/min x 0.50 = 60 m/min). 5xD = 120 m/min 10xD = 60 m/min

For Dynamic Boring Tool NOVI TECH® Length

Boring Type

8xD 0.80 0.90

9xD 0.60 0.70

10xD 0.40 0.50

Roughing Finishing

*Not to exceed recommended RPM printed on NOVI TECH® module.

Assembly of modular components may cause machine damage and/or serious injury. To prevent: -Do not exceed the allowable weight for your machine tool. -Do not exceed the recommended length-to-diameter ratio, which can impact tool stability and performance. For detailed guidelines on safe configurations, please refer to pages B10-M: 9 - 12 or visit www.alliedmachine.com/WohlhaupterBoringGuidelines. WARNING IMPORTANT: Max spindle speed refers to maximum possible speed for an individual boring head and is not a recommended parameter. NOTE: Factory technical assistance is available through our Application Engineering department: appeng@alliedmachine.com. www.alliedmachine.com | 1.330.343.4283 B10-I: 15