B10-WHL_US-EN

BORING | Accessories / Technical InformaƟon

Rough Machining Recommended Cutting Data | Metric (mm)

A

Recommended Feed (mm / tooth) Nose Radii

*Speed

(BHN) Hardness 400 - 600

B

ISO Material

Grade

M / Min 30 - 50 60 - 140 40 - 60 60 - 140

0.2 mm 0.4 mm 0.8 mm

1.2 mm

Wear Plate

Carbide

0.05 - 0.15 0.10 - 0.20 0.10 - 0.20 0.10 - 0.25 0.05 - 0.15 0.10 - 0.20 0.10 - 0.20 0.10 - 0.25 0.05 - 0.15 0.10 - 0.20 0.10 - 0.20 0.10 - 0.25 0.05 - 0.15 0.10 - 0.20 0.10 - 0.20 0.10 - 0.25

Hardox®, AR400, T-1, etc.

CBN

H

Hardened Steel

300 - 500

Carbide

CBN

C

SG / Nodular Cast Iron

120 - 320

Carbide Ceramic Carbide Ceramic

130 - 250 0.10 - 0.15 0.15 - 0.35 0.20 - 0.50 0.20 - 0.80 200 - 400 0.10 - 0.15 0.15 - 0.35 0.20 - 0.50 0.20 - 0.80 150 - 280 0.10 - 0.15 0.15 - 0.35 0.20 - 0.60 0.20 - 0.80 400 - 1000 0.10 - 0.15 0.15 - 0.35 0.20 - 0.60 0.20 - 0.80 250 - 800 0.10 - 0.15 0.15 - 0.35 0.20 - 0.60 0.20 - 0.80 400 - 1200 0.10 - 0.15 0.15 - 0.35 0.20 - 0.60 0.20 - 0.80 200 - 500 0.10 - 0.15 0.15 - 0.35 0.15 - 0.50 0.20 - 0.80

K

Grey / White Iron

180 - 320

D

Cast Aluminum

30 - 180

Carbide

PCD

Wrought Aluminum

30 - 180

Carbide

Aluminum Bronze

100 - 250

Carbide

120 - 250 0.10 - 0.15 0.15 - 0.25 0.15 - 0.40 0.20 - 0.60

N

E

Brass

100

Carbide

200 - 500 0.10 - 0.15 0.15 - 0.25 0.15 - 0.40 0.20 - 0.80

Copper

60

Carbide

100 - 150 0.10 - 0.15 0.15 - 0.25 0.15 - 0.35 0.20 - 0.40

F

*Not to exceed max recommended RPM for boring head found in corresponding Wohlhaupter OperaƟon Manual.

G

H

Deep Hole Boring Speed Adjustment For Dynamic Boring Tool NOVI TECH® Length

Recommended Speed Example If the recommended speed for a finish boring assembly under 5xD is 120 m/min, then the speed for a 10xD finish boring assembly in the same applicaƟon would be 60 m/min (120 m/min x 0.50 = 60 m/min). 5xD = 120 m/min 10xD = 60 m/min

I

Boring Type

8xD 0.80 0.90

9xD 0.60 0.70

10xD 0.40

Roughing Finishing

0.50 *Not to exceed recommended RPM printed on NOVI TECH® module. Single-edge use is recommended.

J

K

L

IMPORTANT: Max spindle speed refers to maximum possible speed for individual boring head and is not a recommended parameter. Factory technical assistance is available for your specific applicaƟons through our ApplicaƟon Engineering department. ext: 7611 | email: appeng@alliedmachine.com Tool failure can cause serious injury. To prevent: -Do not exceed recommended 10xD length-to-diameter raƟo or exceed four total components (including shank). WARNING

M

-When using Alu-Line components, do not exceed recommended 5xD length-to-diameter raƟo. -When using tool steel components, do not exceed recommended 6xD length-to-diameter raƟo. -When using heavy metal components, do not exceed recommended 8xD length-to-diameter raƟo.

-When using a carbide shank, do not exceed recommended 9xD length-to-diameter raƟo. -When using a NOVI TECH® module, do not exceed recommended 10xD length-to-diameter raƟo. Factory technical assistance is available for your specific applicaƟons through our ApplicaƟon Engineering department. ext: 7611 | email: appeng@alliedmachine.com

INDEX

www.alliedmachine.com | 1.330.343.4283

B10-M: 17