CAT-SET

DRILLING | T-A® Replaceable Insert Drilling System

1 Series: 17.53 mm - 24.40 mm (0.6900" - 0.9609")

T-A® Drill Holders

A30

Stub Length

Metric Flange Shank Holders

Body

Shank

L 2

L 4

L 3

L 1

L 5

D 2

P 1

Flute

Series

Length

Part No.

21010S-25FM 22010S-25FM 23010S-25FM 24010S-25FM 25010S-25FM 27010S-25FM 29010S-25FM 21015S-25FM 22015S-25FM 23015S-25FM 24015S-25FM 25015S-25FM 23010H-25FM 24010H-25FM 24510H-25FM 25010H-25FM 26010H-25FM 23015H-25FM 24015H-25FM 25015H-25FM

Stub Short

50.6 75.8 79.3 131.8 56.0 25 66.8 107.2 110.7 163.2 56.0 25 114.8 154.8 158.3 210.8 56.0 25 165.6 205.6 209.1 261.6 56.0 25 454.2 494.5 498.1 550.5 56.0 25 562.1 602.5 606.0 658.5 56.0 25 64.9 88.5 92.0 144.5 56.0 25 66.1 107.2 110.7 163.2 56.0 25 113.8 154.8 158.3 210.8 56.0 25 164.6 205.6 209.1 261.6 56.0 25 132.8 154.8 158.3 210.8 56.0 25 183.6 205.6 209.1 261.6 56.0 25 234.3 256.3 259.9 312.3 56.0 25 380.3 402.3 405.9 458.3 56.0 25 134.4 154.8 158.3 210.8 56.0 25 185.2 205.6 209.1 261.6 56.0 25

1/8 BSPT 1/8 BSPT 1/8 BSPT 1/8 BSPT 1/8 BSPT 1/8 BSPT 1/8 BSPT 1/8 BSPT 1/8 BSPT 1/8 BSPT 1/8 BSPT 1/8 BSPT 1/8 BSPT 1/8 BSPT 1/8 BSPT 1/8 BSPT 1/8 BSPT 1/8 BSPT 1/8 BSPT 1/8 BSPT

Intermediate

Standard

1

Extended 267.2 307.2 310.7 363.2 56.0 25

XL

3XL

Straight

Stub Short

Intermediate

1.5

Standard

Extended 266.2 307.2 310.7 363.2 56.0 25

Intermediate

Standard

Standard Plus

1

Extended 285.2 307.2 310.7 363.2 56.0 25

Long

Helical

Intermediate

Standard

1.5

Extended 286.8 307.2 310.7 363.2 56.0 25

NOTE: Stub length holders have a 3.175 mm (1/8") side pipe tap (P 2 ). NOTE: 1.5 series inserts fit into both 1 and 1.5 series holders. However, 1 series inserts ONLY fit into 1 series holders. See page A30: 7 for visual .

Connection Accessories

Nylon Locking Screws 7375N-IP9-1

Preset Torque Hand Driver

Admissible Tightening Torque* 305 N-cm (27.0 in-lbs) 305 N-cm (27.0 in-lbs)

Series

Insert Screws

Insert Driver

Replacement Tips

1

7375-IP9-1 739-IP9-1

8IP-9 8IP-9

8IP-9TL 8IP-9TL

8IP-9B 8IP-9B

1.5

739N-IP9-1

*Tightening torques are calculated with a friction coefficient of µ = 0.14 and develop 90% of ultimate yield strength.

Refer to Speed and Feed charts for recommended adjustments to speeds and feeds. Refer to page A30: 146 for deep hole drilling guidelines in this section of the catalog. Visit www.alliedmachine.com/DeepHoleGuidelines for the most up-to-date information and procedures. Factory technical assistance is available for your specific applications through our Application Engineering department : appeng@alliedmachine.com. WARNING

A30: 113 - 139

A30: 47 - 54

A30: 60 & 112

Key on A30: 2

Screws sold in multiples of 10. = Metric ( mm) = Imperial (in)

A30: 55

www.alliedmachine.com | 1.330.343.4283